Re: [PATCH V4 3/9] cxl/mem: Wire up event interrupts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, 11 Dec 2022 23:06:21 -0800
ira.weiny@xxxxxxxxx wrote:

> From: Davidlohr Bueso <dave@xxxxxxxxxxxx>
> 
> Currently the only CXL features targeted for irq support require their
> message numbers to be within the first 16 entries.  The device may
> however support less than 16 entries depending on the support it
> provides.
> 
> Attempt to allocate these 16 irq vectors.  If the device supports less
> then the PCI infrastructure will allocate that number.  Upon successful
> allocation, users can plug in their respective isr at any point
> thereafter.
> 
> CXL device events are signaled via interrupts.  Each event log may have
> a different interrupt message number.  These message numbers are
> reported in the Get Event Interrupt Policy mailbox command.
> 
> Add interrupt support for event logs.  Interrupts are allocated as
> shared interrupts.  Therefore, all or some event logs can share the same
> message number.
> 
> In addition all logs are queried on any interrupt in order of the most
> to least severe based on the status register.
> 
> Cc: Bjorn Helgaas <helgaas@xxxxxxxxxx>
> Cc: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> Co-developed-by: Ira Weiny <ira.weiny@xxxxxxxxx>
> Signed-off-by: Ira Weiny <ira.weiny@xxxxxxxxx>
> Signed-off-by: Davidlohr Bueso <dave@xxxxxxxxxxxx>

Sometimes it feels like we go around in circles as I'm sure we've
fixed this at least 3 times now in different sets that got dropped
(was definitely in the DOE interrupt support set and was controversial ;)

Nothing in this patch set calls pci_set_master() so no interrupts
will even be delivered.  I don't think there are any sets in flight
that would fix that.

Jonathan


> 
> ---
> Changes from V3:
> 	Adjust based on changes in patch 1
> 	Consolidate event setup into cxl_event_config()
> 	Consistently use cxl_event_* for function names
> 	Remove cxl_event_int_is_msi()
> 	Ensure DCD log is ignored in status
> 	Simplify event status loop logic
> 	Dan
> 		Fail driver load if the irq's are not allocated
> 		move cxl_event_config_msgnums() to pci.c
> 		s/CXL_PCI_REQUIRED_VECTORS/CXL_PCI_DEFAULT_MAX_VECTORS
> 		s/devm_kmalloc/devm_kzalloc
> 		Fix up pci_alloc_irq_vectors() comment
> 		Pass pdev to cxl_alloc_irq_vectors()
> 		Check FW irq policy prior to configuration
> 	Jonathan
> 		Use FIELD_GET instead of manual masking
> ---
>  drivers/cxl/cxl.h    |   4 +
>  drivers/cxl/cxlmem.h |  19 ++++
>  drivers/cxl/cxlpci.h |   6 ++
>  drivers/cxl/pci.c    | 208 +++++++++++++++++++++++++++++++++++++++++--
>  4 files changed, 231 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h
> index 5974d1082210..b3964149c77b 100644
> --- a/drivers/cxl/cxl.h
> +++ b/drivers/cxl/cxl.h
> @@ -168,6 +168,10 @@ static inline int ways_to_eiw(unsigned int ways, u8 *eiw)
>  				 CXLDEV_EVENT_STATUS_FAIL |	\
>  				 CXLDEV_EVENT_STATUS_FATAL)
>  
> +/* CXL rev 3.0 section 8.2.9.2.4; Table 8-52 */
> +#define CXLDEV_EVENT_INT_MODE_MASK	GENMASK(1, 0)
> +#define CXLDEV_EVENT_INT_MSGNUM_MASK	GENMASK(7, 4)
> +
>  /* CXL 2.0 8.2.8.4 Mailbox Registers */
>  #define CXLDEV_MBOX_CAPS_OFFSET 0x00
>  #define   CXLDEV_MBOX_CAP_PAYLOAD_SIZE_MASK GENMASK(4, 0)
> diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h
> index dd9aa3dd738e..bd8bfbe61ec8 100644
> --- a/drivers/cxl/cxlmem.h
> +++ b/drivers/cxl/cxlmem.h
> @@ -194,6 +194,23 @@ struct cxl_endpoint_dvsec_info {
>  	struct range dvsec_range[2];
>  };
>  
> +/**
> + * Event Interrupt Policy
> + *
> + * CXL rev 3.0 section 8.2.9.2.4; Table 8-52
> + */
> +enum cxl_event_int_mode {
> +	CXL_INT_NONE		= 0x00,
> +	CXL_INT_MSI_MSIX	= 0x01,
> +	CXL_INT_FW		= 0x02
> +};
> +struct cxl_event_interrupt_policy {
> +	u8 info_settings;
> +	u8 warn_settings;
> +	u8 failure_settings;
> +	u8 fatal_settings;
> +} __packed;
> +
>  /**
>   * struct cxl_event_state - Event log driver state
>   *
> @@ -288,6 +305,8 @@ enum cxl_opcode {
>  	CXL_MBOX_OP_RAW			= CXL_MBOX_OP_INVALID,
>  	CXL_MBOX_OP_GET_EVENT_RECORD	= 0x0100,
>  	CXL_MBOX_OP_CLEAR_EVENT_RECORD	= 0x0101,
> +	CXL_MBOX_OP_GET_EVT_INT_POLICY	= 0x0102,
> +	CXL_MBOX_OP_SET_EVT_INT_POLICY	= 0x0103,
>  	CXL_MBOX_OP_GET_FW_INFO		= 0x0200,
>  	CXL_MBOX_OP_ACTIVATE_FW		= 0x0202,
>  	CXL_MBOX_OP_GET_SUPPORTED_LOGS	= 0x0400,
> diff --git a/drivers/cxl/cxlpci.h b/drivers/cxl/cxlpci.h
> index 77dbdb980b12..a8ea04f536ab 100644
> --- a/drivers/cxl/cxlpci.h
> +++ b/drivers/cxl/cxlpci.h
> @@ -53,6 +53,12 @@
>  #define	    CXL_DVSEC_REG_LOCATOR_BLOCK_ID_MASK			GENMASK(15, 8)
>  #define     CXL_DVSEC_REG_LOCATOR_BLOCK_OFF_LOW_MASK		GENMASK(31, 16)
>  
> +/*
> + * NOTE: Currently all the functions which are enabled for CXL require their
> + * vectors to be in the first 16.  Use this as the default max.
> + */
> +#define CXL_PCI_DEFAULT_MAX_VECTORS 16
> +
>  /* Register Block Identifier (RBI) */
>  enum cxl_regloc_type {
>  	CXL_REGLOC_RBI_EMPTY = 0,
> diff --git a/drivers/cxl/pci.c b/drivers/cxl/pci.c
> index a2d8382bc593..d42d87faddb8 100644
> --- a/drivers/cxl/pci.c
> +++ b/drivers/cxl/pci.c
> @@ -445,6 +445,201 @@ static int cxl_mem_alloc_event_buf(struct cxl_dev_state *cxlds)
>  	return 0;
>  }
>  
> +static int cxl_alloc_irq_vectors(struct pci_dev *pdev)
> +{
> +	int nvecs;
> +
> +	/*
> +	 * CXL requires MSI/MSIX support.
> +	 *
> +	 * Additionally pci_alloc_irq_vectors() handles calling
> +	 * pci_free_irq_vectors() automatically despite not being called
> +	 * pcim_*.  See pci_setup_msi_context().
> +	 */
> +	nvecs = pci_alloc_irq_vectors(pdev, 1, CXL_PCI_DEFAULT_MAX_VECTORS,
> +				      PCI_IRQ_MSIX | PCI_IRQ_MSI);
> +	if (nvecs < 1) {
> +		dev_dbg(&pdev->dev, "Failed to alloc irq vectors: %d\n", nvecs);
> +		return -ENXIO;
> +	}
> +	return 0;
> +}
> +
> +struct cxl_dev_id {
> +	struct cxl_dev_state *cxlds;
> +};
> +
> +static irqreturn_t cxl_event_thread(int irq, void *id)
> +{
> +	struct cxl_dev_id *dev_id = id;
> +	struct cxl_dev_state *cxlds = dev_id->cxlds;
> +	u32 status;
> +
> +	do {
> +		/*
> +		 * CXL 3.0 8.2.8.3.1: The lower 32 bits are the status;
> +		 * ignore the reserved upper 32 bits
> +		 */
> +		status = readl(cxlds->regs.status + CXLDEV_DEV_EVENT_STATUS_OFFSET);
> +		/* Ignore logs unknown to the driver */
> +		status &= CXLDEV_EVENT_STATUS_ALL;
> +		if (!status)
> +			break;
> +		cxl_mem_get_event_records(cxlds, status);
> +		cond_resched();
> +	} while (status);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int cxl_event_req_irq(struct cxl_dev_state *cxlds, u8 setting)
> +{
> +	struct device *dev = cxlds->dev;
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	struct cxl_dev_id *dev_id;
> +	int irq;
> +
> +	if (FIELD_GET(CXLDEV_EVENT_INT_MODE_MASK, setting) != CXL_INT_MSI_MSIX)
> +		return -ENXIO;
> +
> +	/* dev_id must be globally unique and must contain the cxlds */
> +	dev_id = devm_kzalloc(dev, sizeof(*dev_id), GFP_KERNEL);
> +	if (!dev_id)
> +		return -ENOMEM;
> +	dev_id->cxlds = cxlds;
> +
> +	irq =  pci_irq_vector(pdev,
> +			      FIELD_GET(CXLDEV_EVENT_INT_MSGNUM_MASK, setting));
> +	if (irq < 0)
> +		return irq;
> +
> +	return devm_request_threaded_irq(dev, irq, NULL, cxl_event_thread,
> +					 IRQF_SHARED, NULL, dev_id);
> +}
> +
> +static int cxl_event_get_int_policy(struct cxl_dev_state *cxlds,
> +				    struct cxl_event_interrupt_policy *policy)
> +{
> +	struct cxl_mbox_cmd mbox_cmd = (struct cxl_mbox_cmd) {
> +		.opcode = CXL_MBOX_OP_GET_EVT_INT_POLICY,
> +		.payload_out = policy,
> +		.size_out = sizeof(*policy),
> +	};
> +	int rc;
> +
> +	rc = cxl_internal_send_cmd(cxlds, &mbox_cmd);
> +	if (rc < 0)
> +		dev_err(cxlds->dev, "Failed to get event interrupt policy : %d",
> +			rc);
> +
> +	return rc;
> +}
> +
> +static int cxl_event_config_msgnums(struct cxl_dev_state *cxlds,
> +				    struct cxl_event_interrupt_policy *policy)
> +{
> +	struct cxl_mbox_cmd mbox_cmd;
> +	int rc;
> +
> +	policy->info_settings = CXL_INT_MSI_MSIX;
> +	policy->warn_settings = CXL_INT_MSI_MSIX;
> +	policy->failure_settings = CXL_INT_MSI_MSIX;
> +	policy->fatal_settings = CXL_INT_MSI_MSIX;
> +
> +	mbox_cmd = (struct cxl_mbox_cmd) {
> +		.opcode = CXL_MBOX_OP_SET_EVT_INT_POLICY,
> +		.payload_in = policy,
> +		.size_in = sizeof(*policy),
> +	};
> +
> +	rc = cxl_internal_send_cmd(cxlds, &mbox_cmd);
> +	if (rc < 0) {
> +		dev_err(cxlds->dev, "Failed to set event interrupt policy : %d",
> +			rc);
> +		return rc;
> +	}
> +
> +	/* Retrieve final interrupt settings */
> +	return cxl_event_get_int_policy(cxlds, policy);
> +}
> +
> +static int cxl_event_irqsetup(struct cxl_dev_state *cxlds)
> +{
> +	struct cxl_event_interrupt_policy policy;
> +	int rc;
> +
> +	rc = cxl_event_config_msgnums(cxlds, &policy);
> +	if (rc)
> +		return rc;
> +
> +	rc = cxl_event_req_irq(cxlds, policy.info_settings);
> +	if (rc) {
> +		dev_err(cxlds->dev, "Failed to get interrupt for event Info log\n");
> +		return rc;
> +	}
> +
> +	rc = cxl_event_req_irq(cxlds, policy.warn_settings);
> +	if (rc) {
> +		dev_err(cxlds->dev, "Failed to get interrupt for event Warn log\n");
> +		return rc;
> +	}
> +
> +	rc = cxl_event_req_irq(cxlds, policy.failure_settings);
> +	if (rc) {
> +		dev_err(cxlds->dev, "Failed to get interrupt for event Failure log\n");
> +		return rc;
> +	}
> +
> +	rc = cxl_event_req_irq(cxlds, policy.fatal_settings);
> +	if (rc) {
> +		dev_err(cxlds->dev, "Failed to get interrupt for event Fatal log\n");
> +		return rc;
> +	}
> +
> +	return 0;
> +}
> +
> +static bool cxl_event_int_is_fw(u8 setting)
> +{
> +	u8 mode = FIELD_GET(CXLDEV_EVENT_INT_MODE_MASK, setting);
> +
> +	return mode == CXL_INT_FW;
> +}
> +
> +static int cxl_event_config(struct pci_host_bridge *host_bridge,
> +			    struct cxl_dev_state *cxlds)
> +{
> +	struct cxl_event_interrupt_policy policy;
> +	int rc;
> +
> +	/*
> +	 * When BIOS maintains CXL error reporting control, it will process
> +	 * event records.  Only one agent can do so.
> +	 */
> +	if (!host_bridge->native_cxl_error)
> +		return 0;
> +
> +	rc = cxl_event_get_int_policy(cxlds, &policy);
> +	if (rc)
> +		return rc;
> +
> +	if (cxl_event_int_is_fw(policy.info_settings) ||
> +	    cxl_event_int_is_fw(policy.warn_settings) ||
> +	    cxl_event_int_is_fw(policy.failure_settings) ||
> +	    cxl_event_int_is_fw(policy.fatal_settings)) {
> +		dev_err(cxlds->dev, "FW still in control of Event Logs despite _OSC settings\n");
> +		return -EBUSY;
> +	}
> +
> +	rc = cxl_event_irqsetup(cxlds);
> +	if (rc)
> +		return rc;
> +
> +	cxl_mem_get_event_records(cxlds, CXLDEV_EVENT_STATUS_ALL);
> +
> +	return 0;
> +}
> +
>  static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  {
>  	struct pci_host_bridge *host_bridge = pci_find_host_bridge(pdev->bus);
> @@ -519,6 +714,10 @@ static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  	if (rc)
>  		return rc;
>  
> +	rc = cxl_alloc_irq_vectors(pdev);
> +	if (rc)
> +		return rc;
> +
>  	cxlmd = devm_cxl_add_memdev(cxlds);
>  	if (IS_ERR(cxlmd))
>  		return PTR_ERR(cxlmd);
> @@ -527,12 +726,9 @@ static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  	if (rc)
>  		return rc;
>  
> -	/*
> -	 * When BIOS maintains CXL error reporting control, it will process
> -	 * event records.  Only one agent can do so.
> -	 */
> -	if (host_bridge->native_cxl_error)
> -		cxl_mem_get_event_records(cxlds, CXLDEV_EVENT_STATUS_ALL);
> +	rc = cxl_event_config(host_bridge, cxlds);
> +	if (rc)
> +		return rc;
>  
>  	if (cxlds->regs.ras) {
>  		pci_enable_pcie_error_reporting(pdev);




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux