From: Bagas Sanjaya <bagasdotme@xxxxxxxxx> The "Filter options" list have a rather ugly indentation. Also, the first paragraph after list name is rendered without separator (as continuation from the name). Align the list by indenting the list items and add a blank line separator for each list name. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> Signed-off-by: Bagas Sanjaya <bagasdotme@xxxxxxxxx> Signed-off-by: Yicong Yang <yangyicong@xxxxxxxxxxxxx> --- .../admin-guide/perf/hisi-pcie-pmu.rst | 80 ++++++++++--------- 1 file changed, 43 insertions(+), 37 deletions(-) diff --git a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst index bbe66480ff85..645f08f65429 100644 --- a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst +++ b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst @@ -48,59 +48,65 @@ Filter options -------------- 1. Target filter -PMU could only monitor the performance of traffic downstream target Root Ports -or downstream target Endpoint. PCIe PMU driver support "port" and "bdf" -interfaces for users, and these two interfaces aren't supported at the same -time. --port -"port" filter can be used in all PCIe PMU events, target Root Port can be -selected by configuring the 16-bits-bitmap "port". Multi ports can be selected -for AP-layer-events, and only one port can be selected for TL/DL-layer-events. + PMU could only monitor the performance of traffic downstream target Root + Ports or downstream target Endpoint. PCIe PMU driver support "port" and + "bdf" interfaces for users, and these two interfaces aren't supported at the + same time. -For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap -should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes), -bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101. + - port -Example usage of perf:: + "port" filter can be used in all PCIe PMU events, target Root Port can be + selected by configuring the 16-bits-bitmap "port". Multi ports can be + selected for AP-layer-events, and only one port can be selected for + TL/DL-layer-events. - $# perf stat -e hisi_pcie0_core0/rx_mwr_latency,port=0x1/ sleep 5 + For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of + bitmap should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 + lanes), bit8 is set, port=0x100; if these two Root Ports are both + monitored, port=0x101. --bdf + Example usage of perf:: -"bdf" filter can only be used in bandwidth events, target Endpoint is selected -by configuring BDF to "bdf". Counter only counts the bandwidth of message -requested by target Endpoint. + $# perf stat -e hisi_pcie0_core0/rx_mwr_latency,port=0x1/ sleep 5 -For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + - bdf -Example usage of perf:: + "bdf" filter can only be used in bandwidth events, target Endpoint is + selected by configuring BDF to "bdf". Counter only counts the bandwidth of + message requested by target Endpoint. + + For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,bdf=0x3900/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,bdf=0x3900/ sleep 5 2. Trigger filter -Event statistics start when the first time TLP length is greater/smaller -than trigger condition. You can set the trigger condition by writing "trig_len", -and set the trigger mode by writing "trig_mode". This filter can only be used -in bandwidth events. -For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" -means statistics start when TLP length > trigger condition, "trig_mode=1" -means start when TLP length < condition. + Event statistics start when the first time TLP length is greater/smaller + than trigger condition. You can set the trigger condition by writing + "trig_len", and set the trigger mode by writing "trig_mode". This filter can + only be used in bandwidth events. -Example usage of perf:: + For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" + means statistics start when TLP length > trigger condition, "trig_mode=1" + means start when TLP length < condition. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 3. Threshold filter -Counter counts when TLP length within the specified range. You can set the -threshold by writing "thr_len", and set the threshold mode by writing -"thr_mode". This filter can only be used in bandwidth events. -For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means -counter counts when TLP length >= threshold, and "thr_mode=1" means counts -when TLP length < threshold. + Counter counts when TLP length within the specified range. You can set the + threshold by writing "thr_len", and set the threshold mode by writing + "thr_mode". This filter can only be used in bandwidth events. -Example usage of perf:: + For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means + counter counts when TLP length >= threshold, and "thr_mode=1" means counts + when TLP length < threshold. + + Example usage of perf:: - $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 + $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 -- 2.24.0
