Re: [PATCH v7 20/20] PCI: dwc: Add Baikal-T1 PCIe controller support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Nov 14, 2022 at 01:01:35PM +0530, Manivannan Sadhasivam wrote:
> On Sun, Nov 13, 2022 at 10:13:01PM +0300, Serge Semin wrote:
> > Baikal-T1 SoC is equipped with DWC PCIe v4.60a host controller. It can be
> > trained to work up to Gen.3 speed over up to x4 lanes. The host controller
> > is attached to the DW PCIe 3.0 PCS via the PIPE-4 interface, which in its
> > turn is connected to the DWC 10G PHY. The whole system is supposed to be
> > fed up with four clock sources: DBI peripheral clock, AXI application
> > clocks and external PHY/core reference clock generating the 100MHz signal.
> > In addition to that the platform provide a way to reset each part of the
> > controller: sticky/non-sticky bits, host controller core, PIPE interface,
> > PCS/PHY and Hot/Power reset signal. The driver also provides a way to
> > handle the GPIO-based PERST# signal.
> > 
> > Note due to the Baikal-T1 MMIO peculiarity we have to implement the DBI
> > interface accessors which make sure the IO operations are dword-aligned.
> > 
> > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > 
> > ---
> > 
> > Changelog v2:
> > - Rename 'syscon' property to 'baikal,bt1-syscon'.
> > 
> > Changelog v3:
> > - Use the clocks/resets handlers defined in the DW PCIe core descriptor.
> >   (@Rob)
> > - Redefine PCI host bridge config space accessors with the generic
> >   pci_generic_config_read32() and pci_generic_config_write32() methods.
> >   (@Rob)
> > 
> > Changelog v4:
> > - Drop PCIBIOS_* macros usage. (@Rob)
> > - Add "static const" to the dw_pcie_ops and dw_pcie_host_ops structure
> >   instances. (@Bjorn)
> > - Rename bt1_pcie_dw_ops to bt1_pcie_ops. (@Bjorn)
> > - Rename bt1_pcie_ops to bt1_pci_ops. (@Bjorn)
> > - Use start_link/stop_link suffixes in the corresponding callbacks.
> >   (@Bjorn)
> > - Change the get_res() method suffix to being get_resources(). (@Bjorn)
> > - Change *_{add,del}_dw_port() method to *_{add,del}_port(). (@Bjorn)
> > - Drop dma_coerce_mask_and_coherent() applied to the PCI host bridge
> >   kernel device instance. (@Bjorn)
> > - Add the comment above the dma_set_mask_and_coherent() method usage
> >   regarding the controller eDMA feature. (@Bjorn)
> > - Fix the comment above the core reset controls assertion. (@Bjorn)
> > - Replace delays and timeout numeric literals with macros. (@Bjorn)
> > 
> > Changelog v6:
> > - Move the DMA-mask setup to the eDMA driver. (@Robin)
> > 
> > Changelog v7:
> > - Replace if-then-dev_err_probe-return statement with just
> > return-dev_err_probe one.
> > ---
> >  drivers/pci/controller/dwc/Kconfig    |   9 +
> >  drivers/pci/controller/dwc/Makefile   |   1 +
> >  drivers/pci/controller/dwc/pcie-bt1.c | 643 ++++++++++++++++++++++++++
> >  3 files changed, 653 insertions(+)
> >  create mode 100644 drivers/pci/controller/dwc/pcie-bt1.c
> > 
> > diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> > index 62ce3abf0f19..771b8b146623 100644
> > --- a/drivers/pci/controller/dwc/Kconfig
> > +++ b/drivers/pci/controller/dwc/Kconfig
> > @@ -222,6 +222,15 @@ config PCIE_ARTPEC6_EP
> >  	  Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
> >  	  endpoint mode. This uses the DesignWare core.
> >  
> > +config PCIE_BT1
> > +	tristate "Baikal-T1 PCIe controller"
> 

> Wondering why cannot this be "PCIE_BAIKAL"? Are you sure that this same driver
> cannot be reused for other Baikal SoCs in future?

Well, there are at least two SoCs: Baikal-M1 and Baikal-S1, which
comprise the Synopsys DW PCIe Host IP-core on boards. But both of them
have different versions of the controller (4.70a and 5.40a, meanwhile
Baikal-T1 has 4.60a) and the clocks/reset/link
enable/disable/establish procedures are also different. So I have much
doubt we should be adding a support for all of them in a single driver
because the only common part for them most likely will be just the
probe and remove methods.) Thus having a generic driver name in the
kernel will cause a confusion (or will require so submit a pre-requisite
config/driver renaming patch) should we decide to submit the drivers
for the new controllers.

> 
> > +	depends on MIPS_BAIKAL_T1 || COMPILE_TEST
> > +	depends on PCI_MSI_IRQ_DOMAIN
> > +	select PCIE_DW_HOST
> > +	help
> > +	  Enables support for the PCIe controller in the Baikal-T1 SoC to work
> > +	  in host mode. It's based on the Synopsys DWC PCIe v4.60a IP-core.
> > +
> >  config PCIE_ROCKCHIP_DW_HOST
> >  	bool "Rockchip DesignWare PCIe controller"
> >  	select PCIE_DW
> > diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> > index 8ba7b67f5e50..bf5c311875a1 100644
> > --- a/drivers/pci/controller/dwc/Makefile
> > +++ b/drivers/pci/controller/dwc/Makefile
> > @@ -3,6 +3,7 @@ obj-$(CONFIG_PCIE_DW) += pcie-designware.o
> >  obj-$(CONFIG_PCIE_DW_HOST) += pcie-designware-host.o
> >  obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
> >  obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
> > +obj-$(CONFIG_PCIE_BT1) += pcie-bt1.o
> >  obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
> >  obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
> >  obj-$(CONFIG_PCIE_FU740) += pcie-fu740.o
> > diff --git a/drivers/pci/controller/dwc/pcie-bt1.c b/drivers/pci/controller/dwc/pcie-bt1.c
> > new file mode 100644
> > index 000000000000..3346770e6654
> > --- /dev/null
> > +++ b/drivers/pci/controller/dwc/pcie-bt1.c
> > @@ -0,0 +1,643 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (C) 2021 BAIKAL ELECTRONICS, JSC
> 

> 2022?

Why not. I'll update this if v8 is required.

> 
> > + *
> > + * Authors:
> > + *   Vadim Vlasov <Vadim.Vlasov@xxxxxxxxxxxxxxxxxxxx>
> > + *   Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > + *
> > + * Baikal-T1 PCIe controller driver
> > + */
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/bits.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/pci.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/reset.h>
> > +#include <linux/types.h>
> > +
> > +#include "pcie-designware.h"
> > +
> > +/* Baikal-T1 System CCU control registers */
> > +#define BT1_CCU_PCIE_CLKC			0x140
> > +#define BT1_CCU_PCIE_REQ_PCS_CLK		BIT(16)
> > +#define BT1_CCU_PCIE_REQ_MAC_CLK		BIT(17)
> > +#define BT1_CCU_PCIE_REQ_PIPE_CLK		BIT(18)
> > +
> > +#define BT1_CCU_PCIE_RSTC			0x144
> > +#define BT1_CCU_PCIE_REQ_LINK_RST		BIT(13)
> > +#define BT1_CCU_PCIE_REQ_SMLH_RST		BIT(14)
> > +#define BT1_CCU_PCIE_REQ_PHY_RST		BIT(16)
> > +#define BT1_CCU_PCIE_REQ_CORE_RST		BIT(24)
> > +#define BT1_CCU_PCIE_REQ_STICKY_RST		BIT(26)
> > +#define BT1_CCU_PCIE_REQ_NSTICKY_RST		BIT(27)
> > +
> > +#define BT1_CCU_PCIE_PMSC			0x148
> > +#define BT1_CCU_PCIE_LTSSM_STATE_MASK		GENMASK(5, 0)
> > +#define BT1_CCU_PCIE_LTSSM_DET_QUIET		0x00
> > +#define BT1_CCU_PCIE_LTSSM_DET_ACT		0x01
> > +#define BT1_CCU_PCIE_LTSSM_POLL_ACT		0x02
> > +#define BT1_CCU_PCIE_LTSSM_POLL_COMP		0x03
> > +#define BT1_CCU_PCIE_LTSSM_POLL_CONF		0x04
> > +#define BT1_CCU_PCIE_LTSSM_PRE_DET_QUIET	0x05
> > +#define BT1_CCU_PCIE_LTSSM_DET_WAIT		0x06
> > +#define BT1_CCU_PCIE_LTSSM_CFG_LNKWD_START	0x07
> > +#define BT1_CCU_PCIE_LTSSM_CFG_LNKWD_ACEPT	0x08
> > +#define BT1_CCU_PCIE_LTSSM_CFG_LNNUM_WAIT	0x09
> > +#define BT1_CCU_PCIE_LTSSM_CFG_LNNUM_ACEPT	0x0a
> > +#define BT1_CCU_PCIE_LTSSM_CFG_COMPLETE		0x0b
> > +#define BT1_CCU_PCIE_LTSSM_CFG_IDLE		0x0c
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_LOCK		0x0d
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_SPEED		0x0e
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_RCVRCFG		0x0f
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_IDLE		0x10
> > +#define BT1_CCU_PCIE_LTSSM_L0			0x11
> > +#define BT1_CCU_PCIE_LTSSM_L0S			0x12
> > +#define BT1_CCU_PCIE_LTSSM_L123_SEND_IDLE	0x13
> > +#define BT1_CCU_PCIE_LTSSM_L1_IDLE		0x14
> > +#define BT1_CCU_PCIE_LTSSM_L2_IDLE		0x15
> > +#define BT1_CCU_PCIE_LTSSM_L2_WAKE		0x16
> > +#define BT1_CCU_PCIE_LTSSM_DIS_ENTRY		0x17
> > +#define BT1_CCU_PCIE_LTSSM_DIS_IDLE		0x18
> > +#define BT1_CCU_PCIE_LTSSM_DISABLE		0x19
> > +#define BT1_CCU_PCIE_LTSSM_LPBK_ENTRY		0x1a
> > +#define BT1_CCU_PCIE_LTSSM_LPBK_ACTIVE		0x1b
> > +#define BT1_CCU_PCIE_LTSSM_LPBK_EXIT		0x1c
> > +#define BT1_CCU_PCIE_LTSSM_LPBK_EXIT_TOUT	0x1d
> > +#define BT1_CCU_PCIE_LTSSM_HOT_RST_ENTRY	0x1e
> > +#define BT1_CCU_PCIE_LTSSM_HOT_RST		0x1f
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_EQ0		0x20
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_EQ1		0x21
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_EQ2		0x22
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_EQ3		0x23
> > +#define BT1_CCU_PCIE_SMLH_LINKUP		BIT(6)
> > +#define BT1_CCU_PCIE_RDLH_LINKUP		BIT(7)
> > +#define BT1_CCU_PCIE_PM_LINKSTATE_L0S		BIT(8)
> > +#define BT1_CCU_PCIE_PM_LINKSTATE_L1		BIT(9)
> > +#define BT1_CCU_PCIE_PM_LINKSTATE_L2		BIT(10)
> > +#define BT1_CCU_PCIE_L1_PENDING			BIT(12)
> > +#define BT1_CCU_PCIE_REQ_EXIT_L1		BIT(14)
> > +#define BT1_CCU_PCIE_LTSSM_RCVR_EQ		BIT(15)
> > +#define BT1_CCU_PCIE_PM_DSTAT_MASK		GENMASK(18, 16)
> > +#define BT1_CCU_PCIE_PM_PME_EN			BIT(20)
> > +#define BT1_CCU_PCIE_PM_PME_STATUS		BIT(21)
> > +#define BT1_CCU_PCIE_AUX_PM_EN			BIT(22)
> > +#define BT1_CCU_PCIE_AUX_PWR_DET		BIT(23)
> > +#define BT1_CCU_PCIE_WAKE_DET			BIT(24)
> > +#define BT1_CCU_PCIE_TURNOFF_REQ		BIT(30)
> > +#define BT1_CCU_PCIE_TURNOFF_ACK		BIT(31)
> > +
> > +#define BT1_CCU_PCIE_GENC			0x14c
> > +#define BT1_CCU_PCIE_LTSSM_EN			BIT(1)
> > +#define BT1_CCU_PCIE_DBI2_MODE			BIT(2)
> > +#define BT1_CCU_PCIE_MGMT_EN			BIT(3)
> > +#define BT1_CCU_PCIE_RXLANE_FLIP_EN		BIT(16)
> > +#define BT1_CCU_PCIE_TXLANE_FLIP_EN		BIT(17)
> > +#define BT1_CCU_PCIE_SLV_XFER_PEND		BIT(24)
> > +#define BT1_CCU_PCIE_RCV_XFER_PEND		BIT(25)
> > +#define BT1_CCU_PCIE_DBI_XFER_PEND		BIT(26)
> > +#define BT1_CCU_PCIE_DMA_XFER_PEND		BIT(27)
> > +
> > +#define BT1_CCU_PCIE_LTSSM_LINKUP(_pmsc) \
> > +({ \
> > +	int __state = FIELD_GET(BT1_CCU_PCIE_LTSSM_STATE_MASK, _pmsc); \
> > +	__state >= BT1_CCU_PCIE_LTSSM_L0 && __state <= BT1_CCU_PCIE_LTSSM_L2_WAKE; \
> > +})
> > +
> > +/* Baikal-T1 PCIe specific control registers */
> > +#define BT1_PCIE_AXI2MGM_LANENUM		0xd04
> > +#define BT1_PCIE_AXI2MGM_LANESEL_MASK		GENMASK(3, 0)
> > +
> > +#define BT1_PCIE_AXI2MGM_ADDRCTL		0xd08
> > +#define BT1_PCIE_AXI2MGM_PHYREG_ADDR_MASK	GENMASK(20, 0)
> > +#define BT1_PCIE_AXI2MGM_READ_FLAG		BIT(29)
> > +#define BT1_PCIE_AXI2MGM_DONE			BIT(30)
> > +#define BT1_PCIE_AXI2MGM_BUSY			BIT(31)
> > +
> > +#define BT1_PCIE_AXI2MGM_WRITEDATA		0xd0c
> > +#define BT1_PCIE_AXI2MGM_WDATA			GENMASK(15, 0)
> > +
> > +#define BT1_PCIE_AXI2MGM_READDATA		0xd10
> > +#define BT1_PCIE_AXI2MGM_RDATA			GENMASK(15, 0)
> > +
> > +/* Generic Baikal-T1 PCIe interface resources */
> > +#define BT1_PCIE_NUM_APP_CLKS			ARRAY_SIZE(bt1_pcie_app_clks)
> > +#define BT1_PCIE_NUM_CORE_CLKS			ARRAY_SIZE(bt1_pcie_core_clks)
> > +#define BT1_PCIE_NUM_APP_RSTS			ARRAY_SIZE(bt1_pcie_app_rsts)
> > +#define BT1_PCIE_NUM_CORE_RSTS			ARRAY_SIZE(bt1_pcie_core_rsts)
> > +
> > +/* PCIe bus setup delays and timeouts */
> > +#define BT1_PCIE_RST_DELAY_MS			100
> > +#define BT1_PCIE_RUN_DELAY_US			100
> > +#define BT1_PCIE_REQ_DELAY_US			1
> > +#define BT1_PCIE_REQ_TIMEOUT_US			1000
> > +#define BT1_PCIE_LNK_DELAY_US			1000
> > +#define BT1_PCIE_LNK_TIMEOUT_US			1000000
> > +
> > +static const enum dw_pcie_app_clk bt1_pcie_app_clks[] = {
> > +	DW_PCIE_DBI_CLK, DW_PCIE_MSTR_CLK, DW_PCIE_SLV_CLK,
> > +};
> > +
> > +static const enum dw_pcie_core_clk bt1_pcie_core_clks[] = {
> > +	DW_PCIE_REF_CLK,
> > +};
> > +
> > +static const enum dw_pcie_app_rst bt1_pcie_app_rsts[] = {
> > +	DW_PCIE_MSTR_RST, DW_PCIE_SLV_RST,
> > +};
> > +
> > +static const enum dw_pcie_core_rst bt1_pcie_core_rsts[] = {
> > +	DW_PCIE_NON_STICKY_RST, DW_PCIE_STICKY_RST, DW_PCIE_CORE_RST,
> > +	DW_PCIE_PIPE_RST, DW_PCIE_PHY_RST, DW_PCIE_HOT_RST, DW_PCIE_PWR_RST,
> > +};
> > +
> > +struct bt1_pcie {
> > +	struct dw_pcie dw;
> > +	struct platform_device *pdev;
> > +	struct regmap *sys_regs;
> > +};
> > +#define to_bt1_pcie(_dw) container_of(_dw, struct bt1_pcie, dw)
> > +
> > +/*
> > + * Baikal-T1 MMIO space must be read/written by the dword-aligned
> > + * instructions. Note the methods are optimized to have the dword operations
> > + * performed with minimum overhead as the most frequently used ones.
> > + */
> > +static int bt1_pcie_read_mmio(void __iomem *addr, int size, u32 *val)
> > +{
> > +	unsigned int ofs = (uintptr_t)addr & 0x3;
> > +
> > +	if (!IS_ALIGNED((uintptr_t)addr, size))
> > +		return -EINVAL;
> > +
> > +	*val = readl(addr - ofs) >> ofs * BITS_PER_BYTE;
> 

> Why can't you use the _relaxed variants?

As a part of a nitpick fix I could, but in this case I don't think
it's very much necessary and IMO it still can be dangerous, since the
IO-accessors utilization is hidden behind the wrapper, which then is
used not only in the LLDD, but in the generic driver too. So depending
on the DW PCIe core driver implementation the strong ordering might be
required if not at the current stage, but in future. So I'd rather be on
the safe side in this case especially seeing it won't give us much
performance gain at runtime since the method is mainly used during the
probe/initialization process.

> 
> > +	if (size == 4) {
> > +		return 0;
> > +	} else if (size == 2) {
> > +		*val &= 0xffff;
> > +		return 0;
> > +	} else if (size == 1) {
> > +		*val &= 0xff;
> > +		return 0;
> > +	}
> > +
> > +	return -EINVAL;
> > +}
> > +
> 
> [...]
> 
> > +/*
> > + * Implements the cold reset procedure in accordance with the reference manual
> > + * and available PM signals.
> > + */
> > +static int bt1_pcie_cold_start_bus(struct bt1_pcie *btpci)
> > +{
> > +	struct device *dev = btpci->dw.dev;
> > +	struct dw_pcie *pci = &btpci->dw;
> > +	u32 val;
> > +	int ret;
> > +
> > +	/* First get out of the Power/Hot reset state */
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PWR_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert PHY reset\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_HOT_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert hot reset\n");
> > +		goto err_assert_pwr_rst;
> > +	}
> > +
> > +	/* Wait for the PM-core to stop requesting the PHY reset */
> 

> What is PM core here? By first look I thought you are referring to Linux PM
> core framework.

See the DW PCIe HW-manual. The IP-core has it's own PM-controller.

> 
> > +	ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_RSTC, val,
> > +				       !(val & BT1_CCU_PCIE_REQ_PHY_RST),
> > +				       BT1_PCIE_REQ_DELAY_US, BT1_PCIE_REQ_TIMEOUT_US);
> > +	if (ret) {
> > +		dev_err(dev, "Timed out waiting for PM to stop PHY resetting\n");
> 
> With relation to my above comment, this log might be confusing.

See above.

> 
> > +		goto err_assert_hot_rst;
> > +	}
> > +
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PHY_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert PHY reset\n");
> > +		goto err_assert_hot_rst;
> > +	}
> > +
> > +	/* Clocks can be now enabled, but the ref one is crucial at this stage */
> > +	ret = clk_bulk_prepare_enable(DW_PCIE_NUM_APP_CLKS, pci->app_clks);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to enable app clocks\n");
> > +		goto err_assert_phy_rst;
> > +	}
> > +
> > +	ret = clk_bulk_prepare_enable(DW_PCIE_NUM_CORE_CLKS, pci->core_clks);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to enable ref clocks\n");
> > +		goto err_disable_app_clk;
> > +	}
> > +
> > +	/* Wait for the PM to stop requesting the controller core reset */
> > +	ret = regmap_read_poll_timeout(btpci->sys_regs, BT1_CCU_PCIE_RSTC, val,
> > +				       !(val & BT1_CCU_PCIE_REQ_CORE_RST),
> > +				       BT1_PCIE_REQ_DELAY_US, BT1_PCIE_REQ_TIMEOUT_US);
> > +	if (ret) {
> > +		dev_err(dev, "Timed out waiting for PM to stop core resetting\n");
> > +		goto err_disable_core_clk;
> > +	}
> > +
> > +	/* PCS-PIPE interface and controller core can be now activated */
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_PIPE_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert PIPE reset\n");
> > +		goto err_disable_core_clk;
> > +	}
> > +
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_CORE_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert core reset\n");
> > +		goto err_assert_pipe_rst;
> > +	}
> > +
> > +	/* It's recommended to reset the core and application logic together */
> > +	ret = reset_control_bulk_reset(DW_PCIE_NUM_APP_RSTS, pci->app_rsts);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to reset app domain\n");
> > +		goto err_assert_core_rst;
> > +	}
> > +
> > +	/* Sticky/Non-sticky CSR flags can be now unreset too */
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_STICKY_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert sticky reset\n");
> > +		goto err_assert_core_rst;
> > +	}
> > +
> > +	ret = reset_control_deassert(pci->core_rsts[DW_PCIE_NON_STICKY_RST].rstc);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to deassert non-sticky reset\n");
> > +		goto err_assert_sticky_rst;
> > +	}
> > +
> > +	/* Activate the PCIe bus peripheral devices */
> > +	gpiod_set_value_cansleep(pci->pe_rst, 0);
> > +
> > +	/* Make sure the state is settled (LTSSM is still disabled though) */
> > +	usleep_range(BT1_PCIE_RUN_DELAY_US, BT1_PCIE_RUN_DELAY_US + 100);
> > +
> > +	return 0;
> > +
> > +err_assert_sticky_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_STICKY_RST].rstc);
> > +
> > +err_assert_core_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_CORE_RST].rstc);
> > +
> > +err_assert_pipe_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_PIPE_RST].rstc);
> > +
> > +err_disable_core_clk:
> > +	clk_bulk_disable_unprepare(DW_PCIE_NUM_CORE_CLKS, pci->core_clks);
> > +
> > +err_disable_app_clk:
> > +	clk_bulk_disable_unprepare(DW_PCIE_NUM_APP_CLKS, pci->app_clks);
> > +
> > +err_assert_phy_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_PHY_RST].rstc);
> > +
> > +err_assert_hot_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_HOT_RST].rstc);
> > +
> > +err_assert_pwr_rst:
> > +	reset_control_assert(pci->core_rsts[DW_PCIE_PWR_RST].rstc);
> > +
> > +	return ret;
> > +}
> > +
> > +static int bt1_pcie_host_init(struct dw_pcie_rp *pp)
> > +{
> > +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > +	struct bt1_pcie *btpci = to_bt1_pcie(pci);
> > +	int ret;
> > +
> > +	ret = bt1_pcie_get_resources(btpci);
> > +	if (ret)
> > +		return ret;
> > +
> > +	bt1_pcie_full_stop_bus(btpci, true);
> > +
> > +	return bt1_pcie_cold_start_bus(btpci);
> > +}
> > +
> > +static void bt1_pcie_host_deinit(struct dw_pcie_rp *pp)
> > +{
> > +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > +	struct bt1_pcie *btpci = to_bt1_pcie(pci);
> > +
> > +	bt1_pcie_full_stop_bus(btpci, false);
> > +}
> > +
> > +static const struct dw_pcie_host_ops bt1_pcie_host_ops = {
> > +	.host_init = bt1_pcie_host_init,
> > +	.host_deinit = bt1_pcie_host_deinit,
> > +};
> > +
> > +static struct bt1_pcie *bt1_pcie_create_data(struct platform_device *pdev)
> > +{
> 

> Since this function is called only from probe, it is better to move it there
> itself. It is common for drivers to allocate platform resource in the probe
> itself.

Already discussed this with Bjorn. One more time. I find it more
readable to leave the probe method as coherent as possible not bulking
everything in there especially seeing the compiler will embed the
static code in there anyway. So no.

> 
> > +	struct bt1_pcie *btpci;
> > +
> > +	btpci = devm_kzalloc(&pdev->dev, sizeof(*btpci), GFP_KERNEL);
> > +	if (!btpci)
> > +		return ERR_PTR(-ENOMEM);
> > +
> > +	btpci->pdev = pdev;
> > +
> > +	platform_set_drvdata(pdev, btpci);
> > +
> > +	return btpci;
> > +}
> > +
> > +static int bt1_pcie_add_port(struct bt1_pcie *btpci)
> > +{
> 

> This also can be moved to probe.

See above.

> 
> > +	struct device *dev = &btpci->pdev->dev;
> > +	int ret;
> > +
> > +	btpci->dw.version = DW_PCIE_VER_460A;
> > +	btpci->dw.dev = dev;
> > +	btpci->dw.ops = &bt1_pcie_ops;
> > +
> > +	btpci->dw.pp.num_vectors = MAX_MSI_IRQS;
> > +	btpci->dw.pp.ops = &bt1_pcie_host_ops;
> > +
> > +	dw_pcie_cap_set(&btpci->dw, REQ_RES);
> > +
> > +	ret = dw_pcie_host_init(&btpci->dw.pp);
> > +
> > +	return dev_err_probe(dev, ret, "Failed to initialize DWC PCIe host\n");
> > +}
> > +
> > +static void bt1_pcie_del_port(struct bt1_pcie *btpci)
> > +{
> > +	dw_pcie_host_deinit(&btpci->dw.pp);
> > +}
> > +
> > +static int bt1_pcie_probe(struct platform_device *pdev)
> > +{
> > +	struct bt1_pcie *btpci;
> > +
> > +	btpci = bt1_pcie_create_data(pdev);
> > +	if (IS_ERR(btpci))
> > +		return PTR_ERR(btpci);
> > +
> > +	return bt1_pcie_add_port(btpci);
> > +}
> > +
> > +static int bt1_pcie_remove(struct platform_device *pdev)
> > +{
> > +	struct bt1_pcie *btpci = platform_get_drvdata(pdev);
> > +
> > +	bt1_pcie_del_port(btpci);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct of_device_id bt1_pcie_of_match[] = {
> > +	{ .compatible = "baikal,bt1-pcie" },
> > +	{},
> > +};
> > +MODULE_DEVICE_TABLE(of, bt1_pcie_of_match);
> > +
> > +static struct platform_driver bt1_pcie_driver = {
> > +	.probe = bt1_pcie_probe,
> > +	.remove = bt1_pcie_remove,
> > +	.driver = {
> > +		.name	= "bt1-pcie",
> > +		.of_match_table = bt1_pcie_of_match,
> 

> You might also want to add PROBE_ASYNCHRONOUS flag to allow parallel probing of
> drivers while the dwc core waits for PHY link to be up in dw_pcie_wait_for_link().

Thanks for reminding me about that flag (though it's
PROBE_PREFER_ASYNCHRONOUS). I was thinking to add it after getting
read the Rob' comment here
https://patchwork.kernel.org/project/linux-pci/patch/20220913101237.4337-1-vidyas@xxxxxxxxxx/#25035943
But then successfully forgot about it. It works well on our platform
and even saves us of 0.5 seconds of the bootup time if no device is
attached to the PCIe controller. No kidding, it's indeed good
suggestion since the whole bootup time is of about 3 seconds. So we'll
be able to reduce it for about 13%. I'll provide this update on v8.

-Sergey

> 
> Thanks,
> Mani 
> 
> > +	},
> > +};
> > +module_platform_driver(bt1_pcie_driver);
> > +
> > +MODULE_AUTHOR("Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Baikal-T1 PCIe driver");
> > +MODULE_LICENSE("GPL");
> > -- 
> > 2.38.1
> > 
> > 
> 
> -- 
> மணிவண்ணன் சதாசிவம்



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux