On Fri, Aug 12, 2022 at 04:52:41PM -0500, Frank Li wrote: > I.MX mu support generate irq by write a register. Provide msi controller > support so other driver such as PCI EP can use it by standard msi > interface as doorbell. > > Signed-off-by: Frank Li <Frank.Li@xxxxxxx> > --- > .../interrupt-controller/fsl,mu-msi.yaml | 93 +++++++++++++++++++ > 1 file changed, 93 insertions(+) > create mode 100644 Documentation/devicetree/bindings/interrupt-controller/fsl,mu-msi.yaml > > diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,mu-msi.yaml b/Documentation/devicetree/bindings/interrupt-controller/fsl,mu-msi.yaml > new file mode 100644 > index 0000000000000..f60fa8b686879 > --- /dev/null > +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,mu-msi.yaml > @@ -0,0 +1,93 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/interrupt-controller/fsl,mu-msi.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: NXP i.MX Messaging Unit (MU) work as msi controller > + > +maintainers: > + - Frank Li <Frank.Li@xxxxxxx> > + > +description: | > + The Messaging Unit module enables two processors within the SoC to > + communicate and coordinate by passing messages (e.g. data, status > + and control) through the MU interface. The MU also provides the ability > + for one processor (A side) to signal the other processor (B side) using > + interrupts. > + > + Because the MU manages the messaging between processors, the MU uses > + different clocks (from each side of the different peripheral buses). > + Therefore, the MU must synchronize the accesses from one side to the > + other. The MU accomplishes synchronization using two sets of matching > + registers (Processor A-facing, Processor B-facing). > + > + MU can work as msi interrupt controller to do doorbell > + > +allOf: > + - $ref: /schemas/interrupt-controller/msi-controller.yaml# > + > +properties: > + compatible: > + enum: > + - fsl,imx6sx-mu-msi > + - fsl,imx7ulp-mu-msi > + - fsl,imx8ulp-mu-msi > + - fsl,imx8ulp-mu-msi-s4 > + > + reg: > + items: > + - description: a side register base address > + - description: b side register base address > + > + reg-names: > + items: > + - const: a > + - const: b > + > + interrupts: > + description: a side interrupt number. How many? > + > + clocks: > + maxItems: 1 > + > + power-domains: > + items: > + - description: a side power domain > + - description: b side power domain > + > + power-domain-names: > + items: > + - const: a > + - const: b > + > + interrupt-controller: true > + > + msi-controller: true #msi-cells? (Missing is treated as 0, but new bindings should be explicit) > + > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-controller > + - msi-controller > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/firmware/imx/rsrc.h> > + > + lsio_mu12: msi-controller@5d270000 { Drop unused labels. > + compatible = "fsl,imx6sx-mu-msi"; > + msi-controller; > + interrupt-controller; > + reg = <0x5d270000 0x10000>, /* A side */ > + <0x5d300000 0x10000>; /* B side */ > + reg-names = "a", "b"; > + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>; > + power-domains = <&pd IMX_SC_R_MU_12A>, > + <&pd IMX_SC_R_MU_12B>; > + power-domain-names = "a", "b"; > + }; > -- > 2.35.1 > >
