On 12/10/11 08:36, Kenji Kaneshige wrote: > Hello, > > According to your dmesg output, pciehp driver doesn't detect any PCIe > hotplug slot. Can you send the following information? > > - ls -lR /sys/bus/pci/slots > - lspci -vvvv (as root user) Hallo, - I tested my system with: * A standard WiFi card (Network controller: Ralink corp. RT2860 --- Belkin Device 817c --- Kernel modules: rt2800pci). * My FPGA board. - I did the following: * I booted the system without the express card & without my FPGA board. 1 - Introduce the express card & my FPGA board after the system has booted up. 2 - lspci -vt doesn't show the express card & FPGA board, express card divers did not loaded (lsmod). 3 - lspci -vt doesn't show my FPGA board. 4 - Rescan the PCIe bus "echo 1 > /sys/bus/pci/rescan" 5 - The express card gets detected (lspci), drivers get loaded (lsmod), But ifconfig doesn't show the interface (wlan0). 6 - My FPGA board gets detected (lspci), but I could not access its registers 0xffffffff. dmesg : [ 152.045433] pci 0000:01:00.0: [1814:0781] type 0 class 0x000280 [ 152.045602] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x0000ffff] [ 152.045854] pci 0000:01:00.0: PME# supported from D0 D3hot [ 152.045980] pci 0000:01:00.0: PME# disabled [ 152.046263] radeon 0000:00:01.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment [ 152.046452] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x4040ffff] [ 152.046606] pci 0000:01:00.0: BAR 0: set to [mem 0x40400000-0x4040ffff] (PCI address [0x40400000-0x4040ffff]) [ 152.075665] cfg80211: Calling CRDA to update world regulatory domain [ 152.116429] rt2800pci 0000:01:00.0: enabling device (0000 -> 0002) [ 152.116598] rt2800pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 152.116770] rt2800pci 0000:01:00.0: setting latency timer to 64 [ 152.127146] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.137537] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.147926] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.158332] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.168723] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.179115] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.189489] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.199864] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.210256] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.220634] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.231088] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.241463] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.251865] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.262270] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.276185] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.290055] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.303865] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x00000580, value=0xffffffff [ 152.307477] phy0 -> rt2800_init_eeprom: Error - Invalid RT chipset detected. [ 152.311073] phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device. [ 152.314700] rt2800pci 0000:01:00.0: PCI INT A disabled [ 172.830318] pci 0000:02:00.0: [1234:0002] type 0 class 0x001180 [ 172.833754] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x00000fff 64bit pref] [ 172.837127] pci 0000:02:00.0: reg 18: [mem 0x00000000-0x0003ffff 64bit pref] [ 172.840456] pci 0000:02:00.0: reg 20: [mem 0x00000000-0x00000fff 64bit pref] [ 172.843964] radeon 0000:00:01.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment [ 172.847331] pci 0000:02:00.0: BAR 2: assigned [mem 0x40200000-0x4023ffff 64bit pref] [ 172.850728] pci 0000:02:00.0: BAR 2: set to [mem 0x40200000-0x4023ffff 64bit pref] (PCI address [0x40200000-0x4023ffff]) [ 172.854231] pci 0000:02:00.0: BAR 0: assigned [mem 0x40240000-0x40240fff 64bit pref] [ 172.857771] pci 0000:02:00.0: BAR 0: set to [mem 0x40240000-0x40240fff 64bit pref] (PCI address [0x40240000-0x40240fff]) [ 172.861339] pci 0000:02:00.0: BAR 4: assigned [mem 0x40241000-0x40241fff 64bit pref] [ 172.864997] pci 0000:02:00.0: BAR 4: set to [mem 0x40241000-0x40241fff 64bit pref] (PCI address [0x40241000-0x40241fff]) 7 - Reset the express card "echo 1 > /sys/bus/pci/devices/0000\:01\:00.0/reset". But ifconfig still doesn't show the interface (wlan0) dmesg : [ 731.717117] pci 0000:01:00.0: restoring config space at offset 0x1 (was 0x100400, writing 0x100002) 8 - Reset my FPGA board "echo 1 > /sys/bus/pci/devices/0000\:02\:00.0/reset". Still I could not access into my FPGA registers. logs : [root@localhost ~]# echo 1 > /sys/bus/pci/devices/0000\:02\:00.0/reset -bash: echo: write error: Invalid argument dmesg : [ 910.928564] pci 0000:02:00.0: restoring config space at offset 0x1 (was 0x100400, writing 0x100000) * I have attached to you the requested information. Many thanks, Ghani
00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex Subsystem: Advanced Micro Devices [AMD] Pavilion DM1Z-3000 Host bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 00:01.0 VGA compatible controller: ATI Technologies Inc Device 9804 (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] Device 1511 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 40 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 1: I/O ports at f000 [size=256] Region 2: Memory at feb00000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 4159 Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Kernel driver in use: radeon Kernel modules: radeon 00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 40400000-405fffff Prefetchable memory behind bridge: 0000000040600000-00000000407fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Slot #4, PowerLimit 75.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 1234 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Kernel driver in use: pcieport 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 40000000-401fffff Prefetchable memory behind bridge: 0000000040200000-00000000403fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Slot #5, PowerLimit 75.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 1234 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> Kernel driver in use: pcieport 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) (prog-if 01 [AHCI 1.0]) Subsystem: ATI Technologies Inc Device 4393 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at f190 [size=8] Region 1: I/O ports at f180 [size=4] Region 2: I/O ports at f170 [size=8] Region 3: I/O ports at f160 [size=4] Region 4: I/O ports at f150 [size=16] Region 5: Memory at feb48000 (32-bit, non-prefetchable) [size=1K] Capabilities: [70] SATA HBA v1.0 InCfgSpace Capabilities: [a4] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ahci 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI]) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at feb47000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI]) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at feb46000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI]) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at feb45000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI]) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at feb44000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) Subsystem: ATI Technologies Inc SBx00 SMBus Controller Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: piix4_smbus Kernel modules: sp5100_tco, i2c-piix4 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) (prog-if 8a [Master SecP PriP]) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at f100 [size=16] Kernel driver in use: pata_atiixp Kernel modules: pata_atiixp 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) Subsystem: ATI Technologies Inc SBx00 Azalia (Intel HDA) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at feb40000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k10temp Kernel modules: k10temp 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 01:00.0 Network controller: Ralink corp. RT2860 Subsystem: Belkin Device 817c Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: Memory at 40400000 (32-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <128ns, L1 <2us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel modules: rt2800pci 02:00.0 Signal processing controller: eZono AG eZono Malta - 32 channels ultrasound front end (rev 01) Subsystem: eZono AG Device 0001 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 0 Region 0: Memory at 40240000 (64-bit, prefetchable) [disabled] [size=4K] Region 2: Memory at 40200000 (64-bit, prefetchable) [disabled] [size=256K] Region 4: Memory at 40241000 (64-bit, prefetchable) [disabled] [size=4K] Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
/sys/bus/pci/slots: total 0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:00.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:01.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:04.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:05.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:11.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:12.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:12.2 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:13.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:13.2 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:14.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:14.1 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:14.2 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:14.3 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:14.4 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.0 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.1 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.2 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.3 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.4 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.5 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.6 drwxr-xr-x 2 root root 0 Aug 29 19:02 0000:00:18.7 drwxr-xr-x 2 root root 0 Aug 29 19:04 0000:01:00.0 drwxr-xr-x 2 root root 0 Aug 29 19:05 0000:02:00.0 /sys/bus/pci/slots/0000:00:00.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:01.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:04.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:05.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:11.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:12.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:12.2: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:13.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:13.2: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:14.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:14.1: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:14.2: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:14.3: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:14.4: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.1: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.2: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.3: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.4: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.5: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.6: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:00:18.7: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:01:00.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power /sys/bus/pci/slots/0000:02:00.0: total 0 -rw-r--r-- 1 root root 4096 Aug 29 19:09 power
