Re: [PATCH v2] PCI: imx6: Fix PERST# start-up sequence

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Just a gently ping. Should I resend adding the acked-by Richard Zhu?

Francesco

On Mon, Feb 14, 2022 at 05:15:22PM +0100, Francesco Dolcini wrote:
> According to the PCIe standard the PERST# signal (reset-gpio in
> fsl,imx* compatible dts) should be kept asserted for at least 100 usec
> before the PCIe refclock is stable, should be kept asserted for at
> least 100 msec after the power rails are stable and the host should wait
> at least 100 msec after it is de-asserted before accessing the
> configuration space of any attached device.
> 
> From PCIe CEM r2.0, sec 2.6.2
> 
>   T-PVPERL: Power stable to PERST# inactive - 100 msec
>   T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
> 
> From PCIe r5.0, sec 6.6.1
> 
>   With a Downstream Port that does not support Link speeds greater than
>   5.0 GT/s, software must wait a minimum of 100 ms before sending a
>   Configuration Request to the device immediately below that Port.
> 
> Failure to do so could prevent PCIe devices to be working correctly,
> and this was experienced with real devices.
> 
> Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
> that PERST# is asserted before enabling any clock, move de-assert to the
> end of imx6_pcie_deassert_core_reset() after the clock is enabled and
> deemed stable and add a new delay of 100 msec just afterward.
> 
> Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@xxxxxxxxxxx
> Fixes: bb38919ec56e ("PCI: imx6: Add support for i.MX6 PCIe controller")
> Signed-off-by: Francesco Dolcini <francesco.dolcini@xxxxxxxxxxx>
> ---
> v2: Add complete reference to the PCIe standards, s/PCI-E/PCIe/g
> ---
>  drivers/pci/controller/dwc/pci-imx6.c | 23 ++++++++++++++---------
>  1 file changed, 14 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> index 7b200b66114a..73baa2044ccf 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -408,6 +408,11 @@ static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie)
>  			dev_err(dev, "failed to disable vpcie regulator: %d\n",
>  				ret);
>  	}
> +
> +	/* Some boards don't have PCIe reset GPIO. */
> +	if (gpio_is_valid(imx6_pcie->reset_gpio))
> +		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
> +					imx6_pcie->gpio_active_high);
>  }
>  
>  static unsigned int imx6_pcie_grp_offset(const struct imx6_pcie *imx6_pcie)
> @@ -544,15 +549,6 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
>  	/* allow the clocks to stabilize */
>  	usleep_range(200, 500);
>  
> -	/* Some boards don't have PCIe reset GPIO. */
> -	if (gpio_is_valid(imx6_pcie->reset_gpio)) {
> -		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
> -					imx6_pcie->gpio_active_high);
> -		msleep(100);
> -		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
> -					!imx6_pcie->gpio_active_high);
> -	}
> -
>  	switch (imx6_pcie->drvdata->variant) {
>  	case IMX8MQ:
>  		reset_control_deassert(imx6_pcie->pciephy_reset);
> @@ -599,6 +595,15 @@ static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie)
>  		break;
>  	}
>  
> +	/* Some boards don't have PCIe reset GPIO. */
> +	if (gpio_is_valid(imx6_pcie->reset_gpio)) {
> +		msleep(100);
> +		gpio_set_value_cansleep(imx6_pcie->reset_gpio,
> +					!imx6_pcie->gpio_active_high);
> +		/* Wait for 100ms after PERST# deassertion (PCIe r5.0, 6.6.1) */
> +		msleep(100);
> +	}
> +
>  	return;
>  
>  err_ref_clk:
> -- 
> 2.25.1
> 



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux