On 22-02-17 11:57:59, Dan Williams wrote:
> On Thu, Feb 17, 2022 at 10:36 AM Ben Widawsky <ben.widawsky@xxxxxxxxx> wrote:
> >
> > Consolidating earlier discussions...
> >
> > On 22-01-28 16:25:34, Dan Williams wrote:
> > > On Thu, Jan 27, 2022 at 4:27 PM Ben Widawsky <ben.widawsky@xxxxxxxxx> wrote:
> > > >
> > > > The region creation APIs create a vacant region. Configuring the region
> > > > works in the same way as similar subsystems such as devdax. Sysfs attrs
> > > > will be provided to allow userspace to configure the region. Finally
> > > > once all configuration is complete, userspace may activate the region.
> > > >
> > > > Introduced here are the most basic attributes needed to configure a
> > > > region. Details of these attribute are described in the ABI
> > >
> > > s/attribute/attributes/
> > >
> > > > Documentation. Sanity checking of configuration parameters are done at
> > > > region binding time. This consolidates all such logic in one place,
> > > > rather than being strewn across multiple places.
> > >
> > > I think that's too late for some of the validation. The complex
> > > validation that the region driver does throughout the topology is
> > > different from the basic input validation that can be done at the
> > > sysfs write time. For example ,this patch allows negative
> > > interleave_granularity values to specified, just return -EINVAL. I
> > > agree that sysfs should not validate everything, I disagree with
> > > pushing all validation to cxl_region_probe().
> > >
> >
> > Okay. It might save us some back and forth if you could outline everything you'd
> > expect to be validated, but I can also make an attempt to figure out the
> > reasonable set of things.
>
> Input validation. Every value that gets written to a sysfs attribute
> should be checked for validity, more below:
>
> >
> > > >
> > > > A example is provided below:
> > > >
> > > > /sys/bus/cxl/devices/region0.0:0
> > > > ├── interleave_granularity
>
> ...validate granularity is within spec and can be supported by the root decoder.
>
> > > > ├── interleave_ways
>
> ...validate ways is within spec and can be supported by the root decoder.
I'm not sure how to do this one. Validation requires device positions and we
can't set the targets until ways is set. Can you please provide some more
insight on what you'd like me to check in addition to the value being within
spec?
>
> > > > ├── offset
> > > > ├── size
>
> ...try to reserve decoder capacity to validate that there is available space.
>
> > > > ├── subsystem -> ../../../../../../bus/cxl
> > > > ├── target0
>
> ...validate that the target maps to the decoder.
>
> > > > ├── uevent
> > > > └── uuid
>
> ...validate that the uuid is unique relative to other regions.
>
> > >
> > > As mentioned off-list, it looks like devtype and modalias are missing.
> > >
> >
> > Yep. This belongs in the previous patch though.
> >
> > > >
> > > > Reported-by: kernel test robot <lkp@xxxxxxxxx> (v2)
> > > > Signed-off-by: Ben Widawsky <ben.widawsky@xxxxxxxxx>
> > > > ---
> > > > Documentation/ABI/testing/sysfs-bus-cxl | 40 ++++
> > > > drivers/cxl/core/region.c | 300 ++++++++++++++++++++++++
> > > > 2 files changed, 340 insertions(+)
> > > >
> > > > diff --git a/Documentation/ABI/testing/sysfs-bus-cxl b/Documentation/ABI/testing/sysfs-bus-cxl
> > > > index dcc728458936..50ba5018014d 100644
> > > > --- a/Documentation/ABI/testing/sysfs-bus-cxl
> > > > +++ b/Documentation/ABI/testing/sysfs-bus-cxl
> > > > @@ -187,3 +187,43 @@ Description:
> > > > region driver before being deleted. The attributes expects a
> > > > region in the form "regionX.Y:Z". The region's name, allocated
> > > > by reading create_region, will also be released.
> > > > +
> > > > +What: /sys/bus/cxl/devices/decoderX.Y/regionX.Y:Z/offset
> > >
> > > This is just another 'resource' attribute for the physical base
> > > address of the region, right? 'offset' sounds like something that
> > > would be relative instead of absolute.
> > >
> >
> > It was meant to be relative. I can make it absolute if that's preferable but the
> > physical base is known at the decoder level already.
>
> Yes, but it saves userspace a step to get the absolute value here and
> matches what happens in PCI sysfs where the user is not required to
> look up the bridge base to calculate the absolute value.
>
> >
> > > > +Date: August, 2021
> > >
> > > Same date update comment here.
> > >
> > > > +KernelVersion: v5.18
> > > > +Contact: linux-cxl@xxxxxxxxxxxxxxx
> > > > +Description:
> > > > + (RO) A region resides within an address space that is claimed by
> > > > + a decoder.
> > >
> > > "A region is a contiguous partition of a CXL Root decoder address space."
> > >
> > > > Region space allocation is handled by the driver, but
> > >
> > > "Region capacity is allocated by writing to the size attribute, the
> > > resulting physical address base determined by the driver is reflected
> > > here."
> > >
> > > > + the offset may be read by userspace tooling in order to
> > > > + determine fragmentation, and available size for new regions.
> > >
> > > I would also expect, before / along with these new region attributes,
> > > there would be 'available' and 'max_extent_available' at the decoder
> > > level to indicate how much free space the decoder has and how big the
> > > next region creation can be. User tooling can walk the decoder and
> > > the regions together to determine fragmentation if necessary, but for
> > > the most part the tool likely only cares about "how big can the next
> > > region be?" and "how full is this decoder?".
> > >
> >
> > Since this is the configuration part of the ABI, I'd rather add that information
> > when the plumbing to report them exists. I'm struggling to understand the
> > balance (as mentioned also earlier in this mail thread) as to what userspace
> > does and what the kernel does. I will add these as you request.
>
> Userspace asks by DPA size and SPA size and the kernel validates /
> performs the allocation on its behalf.
>
> > > > +
> > > > +What:
> > > > +/sys/bus/cxl/devices/decoderX.Y/regionX.Y:Z/{interleave,size,uuid,target[0-15]}
> > > > +Date: August, 2021
> > > > +KernelVersion: v5.18
> > > > +Contact: linux-cxl@xxxxxxxxxxxxxxx
> > > > +Description:
> > > > + (RW) Configuring regions requires a minimal set of parameters in
> > > > + order for the subsequent bind operation to succeed. The
> > > > + following parameters are defined:
> > >
> > > Let's split up the descriptions into individual sections. That can
> > > also document the order that attributes must be written. For example,
> > > doesn't size need to be set before targets are added so that targets
> > > can be validated whether they have sufficient capacity?
> > >
> >
> > Okay. Since we're moving toward making the sysfs ABI stateful,
>
> sysfs is always stateful. Stateless would be an ioctl.
>
> > would you like me
> > to make the attrs only visible when they can actually be set?
>
> No, that's a bit too much magic, and it would be racy.
>
> >
> > > > +
> > > > + == ========================================================
> > > > + interleave_granularity Mandatory. Number of consecutive bytes
> > > > + each device in the interleave set will claim. The
> > > > + possible interleave granularity values are determined by
> > > > + the CXL spec and the participating devices.
> > > > + interleave_ways Mandatory. Number of devices participating in the
> > > > + region. Each device will provide 1/interleave of storage
> > > > + for the region.
> > > > + size Manadatory. Phsyical address space the region will
> > > > + consume.
> > >
> > > s/Phsyical/Physical/
> > >
> > > > + target Mandatory. Memory devices are the backing storage for a
> > > > + region. There will be N targets based on the number of
> > > > + interleave ways that the top level decoder is configured
> > > > + for.
> > >
> > > That doesn't sound right, IW at the root != IW at the endpoint level
> > > and the region needs to record all the endpoint level targets.
> >
> > Correct.
> >
> > >
> > > > Each target must be set with a memdev device ie.
> > > > + 'mem1'. This attribute only becomes available after
> > > > + setting the 'interleave' attribute.
> > > > + uuid Optional. A unique identifier for the region. If none is
> > > > + selected, the kernel will create one.
> > >
> > > Let's drop the Mandatory / Optional distinction, or I am otherwise not
> > > understanding what this is trying to document. For example 'uuid' is
> > > "mandatory" for PMEM regions and "omitted" for volatile regions not
> > > optional.
> >
> > Okay.
> >
> > >
> > > > + == ========================================================
> > > > diff --git a/drivers/cxl/core/region.c b/drivers/cxl/core/region.c
> > > > index 1a448543db0d..3b48e0469fc7 100644
> > > > --- a/drivers/cxl/core/region.c
> > > > +++ b/drivers/cxl/core/region.c
> > > > @@ -3,9 +3,12 @@
> > > > #include <linux/io-64-nonatomic-lo-hi.h>
> > > > #include <linux/device.h>
> > > > #include <linux/module.h>
> > > > +#include <linux/sizes.h>
> > > > #include <linux/slab.h>
> > > > +#include <linux/uuid.h>
> > > > #include <linux/idr.h>
> > > > #include <region.h>
> > > > +#include <cxlmem.h>
> > > > #include <cxl.h>
> > > > #include "core.h"
> > > >
> > > > @@ -18,11 +21,305 @@
> > > > * (programming the hardware) is handled by a separate region driver.
> > > > */
> > > >
> > > > +struct cxl_region *to_cxl_region(struct device *dev);
> > > > +static const struct attribute_group region_interleave_group;
> > > > +
> > > > +static bool is_region_active(struct cxl_region *cxlr)
> > > > +{
> > > > + /* TODO: Regions can't be activated yet. */
> > > > + return false;
> > >
> > > This function seems redundant with just checking "cxlr->dev.driver !=
> > > NULL"? The benefit of that is there is no need to carry a TODO in the
> > > series.
> > >
> >
> > The idea behind this was to give the reviewer somewhat of a bigger picture as to
> > how things should work in the code rather than in a commit message. I will
> > remove this.
>
> They look premature to me.
>
> >
> > > > +}
> > > > +
> > > > +static void remove_target(struct cxl_region *cxlr, int target)
> > > > +{
> > > > + struct cxl_memdev *cxlmd;
> > > > +
> > > > + cxlmd = cxlr->config.targets[target];
> > > > + if (cxlmd)
> > > > + put_device(&cxlmd->dev);
> > >
> > > A memdev can be a member of multiple regions at once, shouldn't this
> > > be an endpoint decoder or similar, not the entire memdev?
> > >
> > > Also, if memdevs autoremove themselves from regions at memdev
> > > ->remove() time then I don't think the region needs to hold references
> > > on memdevs.
> > >
> >
> > This needs some work. The concern I have is region operations will need to
> > operate on memdevs/decoders at various points in time. When the memdev goes
> > away, the region will also need to go away. None of that plumbing was in place
> > in v3 and the reference on the memdev was just a half-hearted attempt at doing
> > the right thing.
> >
> > For now if you prefer I remove the reference, but perhaps the decoder reference
> > would buy us some safety?
>
> So, I don't want to merge an interim solution. I think this series
> needs to prove out the end to end final ABI with all the lifetime
> issues worked out before committing to it upstream because lifetime
> issues get much harder to fix when they also need to conform to a
> legacy ABI.
>
> >
> > > > + cxlr->config.targets[target] = NULL;
> > > > +}
> > > > +
> > > > +static ssize_t interleave_ways_show(struct device *dev,
> > > > + struct device_attribute *attr, char *buf)
> > > > +{
> > > > + struct cxl_region *cxlr = to_cxl_region(dev);
> > > > +
> > > > + return sysfs_emit(buf, "%d\n", cxlr->config.interleave_ways);
> > > > +}
> > > > +
> > > > +static ssize_t interleave_ways_store(struct device *dev,
> > > > + struct device_attribute *attr,
> > > > + const char *buf, size_t len)
> > > > +{
> > > > + struct cxl_region *cxlr = to_cxl_region(dev);
> > > > + int ret, prev_iw;
> > > > + int val;
> > >
> > > I would expect:
> > >
> > > if (dev->driver)
> > > return -EBUSY;
> > >
> > > ...to shutdown configuration writes once the region is active. Might
> > > also need a region-wide seqlock like target_list_show. So that region
> > > probe drains all active sysfs writers before assuming the
> > > configuration is stable.
> >
> > Initially my thought here is that this is a problem for userspace to deal with.
> > If userspace can't figure out how to synchronously configure and bind the
> > region, that's not a kernel problem.
>
> The kernel always needs to protect itself. Userspace is free to race
> itself, but it can not be allowed to trigger a kernel race. So there
> needs to be protection against userspace writing interleave_ways and
> the kernel being able to trust that interleave_ways is now static for
> the life of the region.
>
> > However, we've put some effort into
> > protecting userspace from itself in the create ABI, so it might be more in line
> > to do that here.
>
> That safety was about preventing userspace from leaking kernel memory,
> not about protecting userspace from itself. It's still the case that
> userspace racing itself will get horribly confused when it collides
> region creation, but the kernel protects itself by resolving the race.
>
> > In summary, I'm fine to add it, but I think I really need to get more in your
> > brain about the userspace/kernel divide sooner rather than later.
>
> Don't let userspace break the kernel, that's it.
>
> >
> > >
> > > > +
> > > > + prev_iw = cxlr->config.interleave_ways;
> > > > + ret = kstrtoint(buf, 0, &val);
> > > > + if (ret)
> > > > + return ret;
> > > > + if (ret < 0 || ret > CXL_DECODER_MAX_INTERLEAVE)
> > > > + return -EINVAL;
> > > > +
> > > > + cxlr->config.interleave_ways = val;
> > > > +
> > > > + ret = sysfs_update_group(&dev->kobj, ®ion_interleave_group);
> > > > + if (ret < 0)
> > > > + goto err;
> > > > +
> > > > + sysfs_notify(&dev->kobj, NULL, "target_interleave");
> > >
> > > Why?
> > >
> >
> > copypasta
> >
> > > > +
> > > > + while (prev_iw > cxlr->config.interleave_ways)
> > > > + remove_target(cxlr, --prev_iw);
> > >
> > > To make the kernel side simpler this attribute could just require that
> > > setting interleave ways is a one way street, if you want to change it
> > > you need to delete the region and start over.
> > >
> >
> > Okay. One of the earlier versions did this implicitly since the #ways was needed
> > to create the region. I thought from the ABI perspective, flexibility was good.
> > Userspace may choose not to utilize it.
>
> More flexibility == more maintenance burden. If it's not strictly
> necessary, don't expose it, so making this read-only seems simpler to
> me.
>
> [..]
> > > > + device_lock(&cxlr->dev);
> > > > + if (is_region_active(cxlr))
> > > > + rc = -EBUSY;
> > > > + else
> > > > + cxlr->config.size = val;
> > > > + device_unlock(&cxlr->dev);
> > >
> > > I think lockdep will complain about device_lock() usage in an
> > > attribute. Try changing this to cxl_device_lock() with
> > > CONFIG_PROVE_CXL_LOCKING=y.
> > >
> >
> > I might have messed it up, but I didn't seem to run into an issue. With the
> > driver bound check though, it can go away.
> >
> > I think it would be really good to add this kind of detail to sysfs.rst. Quick
> > grep finds me arm64/kernel/mte and the nfit driver taking the device lock in an
> > attr.
>
> Yeah, CONFIG_PROVE_{NVDIMM,CXL}_LOCKING needs to annotate the
> driver-core as well. I'm concerned there's a class of deadlocks that
> lockdep just can't see.
>
> >
> >
> > > > +
> > > > + return rc ? rc : len;
> > > > +}
> > > > +static DEVICE_ATTR_RW(size);
> > > > +
> > > > +static ssize_t uuid_show(struct device *dev, struct device_attribute *attr,
> > > > + char *buf)
> > > > +{
> > > > + struct cxl_region *cxlr = to_cxl_region(dev);
> > > > +
> > > > + return sysfs_emit(buf, "%pUb\n", &cxlr->config.uuid);
> > > > +}
> > > > +
> > > > +static ssize_t uuid_store(struct device *dev, struct device_attribute *attr,
> > > > + const char *buf, size_t len)
> > > > +{
> > > > + struct cxl_region *cxlr = to_cxl_region(dev);
> > > > + ssize_t rc;
> > > > +
> > > > + if (len != UUID_STRING_LEN + 1)
> > > > + return -EINVAL;
> > > > +
> > > > + device_lock(&cxlr->dev);
> > > > + if (is_region_active(cxlr))
> > > > + rc = -EBUSY;
> > > > + else
> > > > + rc = uuid_parse(buf, &cxlr->config.uuid);
> > > > + device_unlock(&cxlr->dev);
> > > > +
> > > > + return rc ? rc : len;
> > > > +}
> > > > +static DEVICE_ATTR_RW(uuid);
> > > > +
> > > > +static struct attribute *region_attrs[] = {
> > > > + &dev_attr_interleave_ways.attr,
> > > > + &dev_attr_interleave_granularity.attr,
> > > > + &dev_attr_offset.attr,
> > > > + &dev_attr_size.attr,
> > > > + &dev_attr_uuid.attr,
> > > > + NULL,
> > > > +};
> > > > +
> > > > +static const struct attribute_group region_group = {
> > > > + .attrs = region_attrs,
> > > > +};
> > > > +
> > > > +static size_t show_targetN(struct cxl_region *cxlr, char *buf, int n)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + device_lock(&cxlr->dev);
> > > > + if (!cxlr->config.targets[n])
> > > > + ret = sysfs_emit(buf, "\n");
> > > > + else
> > > > + ret = sysfs_emit(buf, "%s\n",
> > > > + dev_name(&cxlr->config.targets[n]->dev));
> > > > + device_unlock(&cxlr->dev);
> > >
> > > The component contribution of a memdev to a region is a DPA-span, not
> > > the whole memdev. I would expect something like dax_mapping_attributes
> > > or REGION_MAPPING() from drivers/nvdimm/region_devs.c. A tuple of
> > > information about the component contribution of a memdev to a region.
> > >
> >
> > I think show_target should just return the chosen decoder and then the decoder
> > attributes will tell the rest, wouldn't they?
>
> Given the conflicts that can arise between HDM decoders needing to map
> increasing DPA values and other conflicts that there will be
> situations where the kernel auto-picking a decoder will get in the
> way. Exposing the decoder selection to userspace also gives one more
> place to do leaf validation. I.e. at decoder-to-region assignment time
> the kernel can validate that the DPA is available and can be mapped by
> the given decoder given the state of other decoders on that device.
>
> >
> > > > +
> > > > + return ret;
> > > > +}
> > > > +
> > > > +static size_t set_targetN(struct cxl_region *cxlr, const char *buf, int n,
> > > > + size_t len)
> > > > +{
> > > > + struct device *memdev_dev;
> > > > + struct cxl_memdev *cxlmd;
> > > > +
> > > > + device_lock(&cxlr->dev);
> > > > +
> > > > + if (len == 1 || cxlr->config.targets[n])
> > > > + remove_target(cxlr, n);
> > > > +
> > > > + /* Remove target special case */
> > > > + if (len == 1) {
> > > > + device_unlock(&cxlr->dev);
> > > > + return len;
> > > > + }
> > > > +
> > > > + memdev_dev = bus_find_device_by_name(&cxl_bus_type, NULL, buf);
> > >
> > > I think this wants to be an endpoint decoder, not a memdev. Because
> > > it's the decoder that joins a memdev to a region, or at least a
> > > decoder should be picked when the memdev is assigned so that the DPA
> > > mapping can be registered. If all the decoders are allocated then fail
> > > here.
> > >
> >
> > Per above, I think making this decoders makes sense. I could make it flexible
> > for ease of use, like if you specify memX, the kernel will pick a decoder for
> > you however I suspect you won't like that.
>
> Right, put the user friendliness in the tooling, not sysfs ABI.
>
> >
> > > > + if (!memdev_dev) {
> > > > + device_unlock(&cxlr->dev);
> > > > + return -ENOENT;
> > > > + }
> > > > +
> > > > + /* reference to memdev held until target is unset or region goes away */
> > > > +
> > > > + cxlmd = to_cxl_memdev(memdev_dev);
> > > > + cxlr->config.targets[n] = cxlmd;
> > > > +
> > > > + device_unlock(&cxlr->dev);
> > > > +
> > > > + return len;
> > > > +}
> > > > +
> > > > +#define TARGET_ATTR_RW(n) \
> > > > + static ssize_t target##n##_show( \
> > > > + struct device *dev, struct device_attribute *attr, char *buf) \
> > > > + { \
> > > > + return show_targetN(to_cxl_region(dev), buf, (n)); \
> > > > + } \
> > > > + static ssize_t target##n##_store(struct device *dev, \
> > > > + struct device_attribute *attr, \
> > > > + const char *buf, size_t len) \
> > > > + { \
> > > > + return set_targetN(to_cxl_region(dev), buf, (n), len); \
> > > > + } \
> > > > + static DEVICE_ATTR_RW(target##n)
> > > > +
> > > > +TARGET_ATTR_RW(0);
> > > > +TARGET_ATTR_RW(1);
> > > > +TARGET_ATTR_RW(2);
> > > > +TARGET_ATTR_RW(3);
> > > > +TARGET_ATTR_RW(4);
> > > > +TARGET_ATTR_RW(5);
> > > > +TARGET_ATTR_RW(6);
> > > > +TARGET_ATTR_RW(7);
> > > > +TARGET_ATTR_RW(8);
> > > > +TARGET_ATTR_RW(9);
> > > > +TARGET_ATTR_RW(10);
> > > > +TARGET_ATTR_RW(11);
> > > > +TARGET_ATTR_RW(12);
> > > > +TARGET_ATTR_RW(13);
> > > > +TARGET_ATTR_RW(14);
> > > > +TARGET_ATTR_RW(15);
> > > > +
> > > > +static struct attribute *interleave_attrs[] = {
> > > > + &dev_attr_target0.attr,
> > > > + &dev_attr_target1.attr,
> > > > + &dev_attr_target2.attr,
> > > > + &dev_attr_target3.attr,
> > > > + &dev_attr_target4.attr,
> > > > + &dev_attr_target5.attr,
> > > > + &dev_attr_target6.attr,
> > > > + &dev_attr_target7.attr,
> > > > + &dev_attr_target8.attr,
> > > > + &dev_attr_target9.attr,
> > > > + &dev_attr_target10.attr,
> > > > + &dev_attr_target11.attr,
> > > > + &dev_attr_target12.attr,
> > > > + &dev_attr_target13.attr,
> > > > + &dev_attr_target14.attr,
> > > > + &dev_attr_target15.attr,
> > > > + NULL,
> > > > +};
> > > > +
> > > > +static umode_t visible_targets(struct kobject *kobj, struct attribute *a, int n)
> > > > +{
> > > > + struct device *dev = container_of(kobj, struct device, kobj);
> > > > + struct cxl_region *cxlr = to_cxl_region(dev);
> > > > +
> > > > + if (n < cxlr->config.interleave_ways)
> > > > + return a->mode;
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct attribute_group region_interleave_group = {
> > > > + .attrs = interleave_attrs,
> > > > + .is_visible = visible_targets,
> > > > +};
> > > > +
> > > > +static const struct attribute_group *region_groups[] = {
> > > > + ®ion_group,
> > > > + ®ion_interleave_group,
> > > > + NULL,
> > > > +};
> > > > +
> > > > static void cxl_region_release(struct device *dev);
> > > >
> > > > static const struct device_type cxl_region_type = {
> > > > .name = "cxl_region",
> > > > .release = cxl_region_release,
> > > > + .groups = region_groups
> > > > };
> > > >
> > > > static ssize_t create_region_show(struct device *dev,
> > > > @@ -108,8 +405,11 @@ static void cxl_region_release(struct device *dev)
> > > > {
> > > > struct cxl_decoder *cxld = to_cxl_decoder(dev->parent);
> > > > struct cxl_region *cxlr = to_cxl_region(dev);
> > > > + int i;
> > > >
> > > > ida_free(&cxld->region_ida, cxlr->id);
> > > > + for (i = 0; i < cxlr->config.interleave_ways; i++)
> > > > + remove_target(cxlr, i);
> > >
> > > Like the last patch this feels too late. I expect whatever unregisters
> > > the region should have already handled removing the targets.
> > >
> >
> > Would remove() be more appropriate?
>
> ->remove() does not seem a good fit since it may be the case that
> someone wants do "echo $region >
> /sys/bus/cxl/drivers/cxl_region/unbind; echo $region >
> /sys/bus/cxl/drivers/cxl_region/bind;" without needing to go
> reconfigure the targets. I am suggesting that before
> device_unregister(&cxlr->dev) the targets are released.
