On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > This adds support for legacy INTx interrupts received from other PCIe > > > devices and which are reported by a new INTx irq chip. > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > interrupts. > > > > > > Note that for this support, device tree files has to be properly adjusted > > > to provide "interrupts" or "interrupts-extended" property with intx > > > interrupt source, "interrupt-names" property with "intx" string and also > > > 'interrupt-controller' subnode must be defined. > > > > > > If device tree files do not provide these nodes then driver would work as > > > before. > > > > Nit: this information is not useful. DT rules are written in DT > > bindings, not in kernel commit logs. All I am saying is that firmware > > developers should not have to read this log to write firmware. > > It was not intended for firmware developers, but for reviewers of this > patch to understand, what is happening in code and that with old DT > files this patch does not change driver behavior (= work as before). > > > > Signed-off-by: Pali Rohár <pali@xxxxxxxxxx> > > > --- > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > --- a/drivers/pci/controller/pci-mvebu.c > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > @@ -54,9 +54,10 @@ > > > PCIE_CONF_ADDR_EN) > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > Nit: I understand it is tempting but here you are redefining or better > > giving a proper label to a register. Separate patch please. > > Ok! > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > #define PCIE_INT_PM_PME BIT(28) > > > -#define PCIE_MASK_OFF 0x1910 > > > > See above. > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > #define PCIE_CTRL_OFF 0x1a00 > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > struct mvebu_pcie_window iowin; > > > u32 saved_pcie_stat; > > > struct resource regs; > > > + struct irq_domain *intx_irq_domain; > > > + raw_spinlock_t irq_lock; > > > + int intx_irq; > > > }; > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > { > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > mvebu_pcie_setup_wins(port); > > > > > > - /* Enable interrupt lines A-D. */ > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > + /* Mask all interrupt sources. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > + > > > + /* Clear all interrupt causes. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > + > > > + if (port->intx_irq <= 0) { > > > + /* > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > + * this case driver does not provide a way for masking and > > > + * unmasking of individual legacy INTx interrupts. In this case > > > + * all interrupts, including legacy INTx are reported via one > > > + * shared GIC source and therefore kernel cannot distinguish > > > + * which individual legacy INTx was triggered. These interrupts > > > + * are shared, so it should not cause any issue. Just > > > + * performance penalty as every PCIe interrupt handler needs to > > > + * be called when some interrupt is triggered. > > > + */ > > > > This comment applies to current mainline right (ie it describes how > > current mainline handles INTx) ? IMO you should split it out in a > > separate patch. > > This above comment describe what happens in if-branch when intx_irq is > not set (as written in comment "when intx interrupt was not specified in > DT"). You are right that this is also the behavior in the current > mainline. > > I'm not sure if this comment can be split out as support for "intx" > interrupt is in this patch. > > > I understand it is hard but a patch is a logical _change_, this > > comment is a change per se, it is a clarification on current > > behaviour. > > Ok, I could try to split this comment into two patches, but part about > if-branch comment needs to stay in "this" patch. I have done it locally. Let me know when I should resend this patch series and I will include into it also these changes. > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask |= PCIE_INT_INTX(0) | PCIE_INT_INTX(1) | > > > + PCIE_INT_INTX(2) | PCIE_INT_INTX(3); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + } > > > } > > > > > > static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, > > > @@ -924,6 +948,108 @@ static struct pci_ops mvebu_pcie_ops = { > > > .write = mvebu_pcie_wr_conf, > > > }; > > > > > > +static void mvebu_pcie_intx_irq_mask(struct irq_data *d) > > > +{ > > > + struct mvebu_pcie_port *port = d->domain->host_data; > > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > > + unsigned long flags; > > > + u32 unmask; > > > + > > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask &= ~PCIE_INT_INTX(hwirq); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > > +} > > > + > > > +static void mvebu_pcie_intx_irq_unmask(struct irq_data *d) > > > +{ > > > + struct mvebu_pcie_port *port = d->domain->host_data; > > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > > + unsigned long flags; > > > + u32 unmask; > > > + > > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask |= PCIE_INT_INTX(hwirq); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > > +} > > > + > > > +static struct irq_chip intx_irq_chip = { > > > + .name = "mvebu-INTx", > > > + .irq_mask = mvebu_pcie_intx_irq_mask, > > > + .irq_unmask = mvebu_pcie_intx_irq_unmask, > > > +}; > > > + > > > +static int mvebu_pcie_intx_irq_map(struct irq_domain *h, > > > + unsigned int virq, irq_hw_number_t hwirq) > > > +{ > > > + struct mvebu_pcie_port *port = h->host_data; > > > + > > > + irq_set_status_flags(virq, IRQ_LEVEL); > > > + irq_set_chip_and_handler(virq, &intx_irq_chip, handle_level_irq); > > > + irq_set_chip_data(virq, port); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { > > > + .map = mvebu_pcie_intx_irq_map, > > > + .xlate = irq_domain_xlate_onecell, > > > +}; > > > + > > > +static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) > > > +{ > > > + struct device *dev = &port->pcie->pdev->dev; > > > + struct device_node *pcie_intc_node; > > > + > > > + raw_spin_lock_init(&port->irq_lock); > > > + > > > + pcie_intc_node = of_get_next_child(port->dn, NULL); > > > + if (!pcie_intc_node) { > > > + dev_err(dev, "No PCIe Intc node found for %s\n", port->name); > > > + return -ENODEV; > > > + } > > > + > > > + port->intx_irq_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, > > > + &mvebu_pcie_intx_irq_domain_ops, > > > + port); > > > + of_node_put(pcie_intc_node); > > > + if (!port->intx_irq_domain) { > > > + dev_err(dev, "Failed to get INTx IRQ domain for %s\n", port->name); > > > + return -ENOMEM; > > > + } > > > + > > > + return 0; > > > +} > > > + > > > +static void mvebu_pcie_irq_handler(struct irq_desc *desc) > > > +{ > > > + struct mvebu_pcie_port *port = irq_desc_get_handler_data(desc); > > > + struct irq_chip *chip = irq_desc_get_chip(desc); > > > + struct device *dev = &port->pcie->pdev->dev; > > > + u32 cause, unmask, status; > > > + int i; > > > + > > > + chained_irq_enter(chip, desc); > > > + > > > + cause = mvebu_readl(port, PCIE_INT_CAUSE_OFF); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + status = cause & unmask; > > > + > > > + /* Process legacy INTx interrupts */ > > > + for (i = 0; i < PCI_NUM_INTX; i++) { > > > + if (!(status & PCIE_INT_INTX(i))) > > > + continue; > > > + > > > + if (generic_handle_domain_irq(port->intx_irq_domain, i) == -EINVAL) > > > + dev_err_ratelimited(dev, "unexpected INT%c IRQ\n", (char)i+'A'); > > > + } > > > + > > > + chained_irq_exit(chip, desc); > > > +} > > > + > > > static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) > > > { > > > /* Interrupt support on mvebu emulated bridges is not implemented yet */ > > > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > > > port->io_attr = -1; > > > } > > > > > > + /* > > > + * Old DT bindings do not contain "intx" interrupt > > > + * so do not fail probing driver when interrupt does not exist. > > > + */ > > > + port->intx_irq = of_irq_get_byname(child, "intx"); > > > + if (port->intx_irq == -EPROBE_DEFER) { > > > + ret = port->intx_irq; > > > + goto err; > > > + } > > > + if (port->intx_irq <= 0) { > > > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > > > + "%pOF does not contain intx interrupt\n", > > > + port->name, child); > > > > Here you end up with a new warning on existing firmware. Is it > > legitimate ? I would remove the dev_warn(). > > I added this warning in v2 because Marc wanted it. > > Should I (again) remove it in v3? > > > Rob certainly has more insightful advice on this. > > > > Thanks, > > Lorenzo > > > > > + } > > > + > > > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); > > > if (reset_gpio == -EPROBE_DEFER) { > > > ret = reset_gpio; > > > @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > child = port->dn; > > > if (!child) > > > @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > continue; > > > } > > > > > > + if (irq > 0) { > > > + ret = mvebu_pcie_init_irq_domain(port); > > > + if (ret) { > > > + dev_err(dev, "%s: cannot init irq domain\n", > > > + port->name); > > > + pci_bridge_emul_cleanup(&port->bridge); > > > + devm_iounmap(dev, port->base); > > > + port->base = NULL; > > > + mvebu_pcie_powerdown(port); > > > + continue; > > > + } > > > + irq_set_chained_handler_and_data(irq, > > > + mvebu_pcie_irq_handler, > > > + port); > > > + } > > > + > > > /* > > > * PCIe topology exported by mvebu hw is quite complicated. In > > > * reality has something like N fully independent host bridges > > > @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > if (!port->base) > > > continue; > > > @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > mvebu_writel(port, cmd, PCIE_CMD_OFF); > > > > > > /* Mask all interrupt sources. */ > > > - mvebu_writel(port, 0, PCIE_MASK_OFF); > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > + > > > + /* Clear all interrupt causes. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > + > > > + if (irq > 0) > > > + irq_set_chained_handler_and_data(irq, NULL, NULL); > > > + > > > + /* Remove IRQ domains. */ > > > + if (port->intx_irq_domain) > > > + irq_domain_remove(port->intx_irq_domain); > > > > > > /* Free config space for emulated root bridge. */ > > > pci_bridge_emul_cleanup(&port->bridge); > > > -- > > > 2.20.1 > > >