Hi,
On Wed, Jan 26, 2022 at 03:18:51PM +0800, Kai-Heng Feng wrote:
> Commit 50310600ebda ("iommu/vt-d: Enable PCI ACS for platform opt in
> hint") enables ACS, and some platforms lose its NVMe after resume from
> S3:
> [ 50.947816] pcieport 0000:00:1b.0: DPC: containment event, status:0x1f01 source:0x0000
> [ 50.947817] pcieport 0000:00:1b.0: DPC: unmasked uncorrectable error detected
> [ 50.947829] pcieport 0000:00:1b.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Receiver ID)
> [ 50.947830] pcieport 0000:00:1b.0: device [8086:06ac] error status/mask=00200000/00010000
> [ 50.947831] pcieport 0000:00:1b.0: [21] ACSViol (First)
> [ 50.947841] pcieport 0000:00:1b.0: AER: broadcast error_detected message
> [ 50.947843] nvme nvme0: frozen state error detected, reset controller
>
> It happens right after ACS gets enabled during resume.
Is this really because of the above commit of due the fact that AER
"service" never implemented the PM hooks in the first place ;-)
>
> There's another case, when Thunderbolt reaches D3cold:
> [ 30.100211] pcieport 0000:00:1d.0: AER: Uncorrected (Non-Fatal) error received: 0000:00:1d.0
> [ 30.100251] pcieport 0000:00:1d.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
> [ 30.100256] pcieport 0000:00:1d.0: device [8086:7ab0] error status/mask=00100000/00004000
> [ 30.100262] pcieport 0000:00:1d.0: [20] UnsupReq (First)
> [ 30.100267] pcieport 0000:00:1d.0: AER: TLP Header: 34000000 08000052 00000000 00000000
> [ 30.100372] thunderbolt 0000:0a:00.0: AER: can't recover (no error_detected callback)
> [ 30.100401] xhci_hcd 0000:3e:00.0: AER: can't recover (no error_detected callback)
> [ 30.100427] pcieport 0000:00:1d.0: AER: device recovery failed
>
> Since PCIe spec "5.2 Link State Power Management" states that TLP and DLLP
> transmission is disabled for a Link in L2/L3 Ready (D3hot), L2 (D3cold with aux
> power) and L3 (D3cold), so disable AER to avoid the noises from turning power
> rails on/off.
I think more accurate here is to say when the topology behind the root
port enters low power states. Reason here is that you can't really tell
from the OS standpoint whether the link went into L1 or L2/3 before the
ACPI power resource is turned off.
> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209149
> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215453
> Fixes: 50310600ebda ("iommu/vt-d: Enable PCI ACS for platform opt in hint")
> Signed-off-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
Thanks for fixing this!
Reviewed-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
