On Thursday, September 22, 2011, Sarah Sharp wrote: > On Mon, Sep 19, 2011 at 11:43:33PM +0200, Rafael J. Wysocki wrote: > > Hi, > > > > Sorry for the delayed response, I was traveling during the last week too. > > No worries. :) > > > On Monday, September 12, 2011, Sarah Sharp wrote: > > > Hi Rafael, > > > > > > As I mentioned at LPC, I have a USB host controller that is failing to > > > wakeup from D3 when a new USB device is connected to an external hub. > > > The system is in S0 at this point. > > > > > > You mentioned that there were two ways for hardware to generate PMEs: > > > either through the standard PCI interrupt process, or via an ACPI SCI > > > call. > > > > > > I think the hardware engineers want Linux to set up the PCI device to > > > generate PMEs via an SCI call, but I'm not sure if Linux is. I've tried > > > turning on ACPI debugging (with level and layers both set to 0xffffffff > > > so I can see all debugging), and I don't see any output at all from ACPI > > > functions like acpi_ev_sci_xrupt_handler when the host controller comes > > > out of D3. (It does come out of D3 if I plug in the device within 10 > > > seconds of PCI suspend, for whatever reason.) > > > > > > Is there a way to tell if SCI is being used by a PCI device to generate > > > PMEs? > > > > Yes, there is. First, if the native PCIe PME is used (which means SCI isn't), > > there will be entries like these in /proc/interrupts: > > > > 40: 0 0 PCI-MSI-edge PCIe PME > > 41: 0 0 PCI-MSI-edge PCIe PME > > 42: 0 0 PCI-MSI-edge PCIe PME > > > > If they are not present, it means that the kernel is _trying_ to use SCI > > for PME signaling. In that case, you can check if the number of ACPI > > interrupts in /proc/interrupts is increasing when you try to trigger the > > events. > > Ok, here's what /proc/interrupts shows for my system: > > CPU0 CPU1 CPU2 CPU3 > 0: 28 0 0 0 IR-IO-APIC-edge timer > 8: 1 0 0 0 IR-IO-APIC-edge rtc0 > 9: 0 0 0 0 IR-IO-APIC-fasteoi acpi > 16: 795 0 0 0 IR-IO-APIC-fasteoi ehci_hcd:usb1 > 19: 16 0 0 0 IR-IO-APIC-fasteoi firewire_ohci > 23: 34 0 0 0 IR-IO-APIC-fasteoi ehci_hcd:usb2 > 40: 0 0 0 0 DMAR_MSI-edge dmar0 > 42: 2931 0 0 0 IR-PCI-MSI-edge eth7 > 43: 13285 0 0 0 IR-PCI-MSI-edge ahci > 44: 0 0 0 0 IR-PCI-MSI-edge xhci_hcd > 45: 558 0 0 0 IR-PCI-MSI-edge snd_hda_intel > 46: 235 0 204 0 IR-PCI-MSI-edge snd_hda_intel > 47: 808 0 0 0 IR-PCI-MSI-edge radeon > NMI: 0 0 0 0 Non-maskable interrupts > LOC: 14857 14209 44533 15822 Local timer interrupts > SPU: 0 0 0 0 Spurious interrupts > PMI: 0 0 0 0 Performance monitoring interrupts > IWI: 0 0 0 0 IRQ work interrupts > RES: 11671 13274 2835 4637 Rescheduling interrupts > CAL: 210 311 396 470 Function call interrupts > TLB: 287 242 135 296 TLB shootdowns > TRM: 0 0 0 0 Thermal event interrupts > THR: 0 0 0 0 Threshold APIC interrupts > MCE: 0 0 0 0 Machine check exceptions > MCP: 5 5 5 5 Machine check polls > ERR: 0 > MIS: 0 > > I don't see any PCIe PME entries, so can I assume that ACPI is trying to use > SCI? Yes. > > In that case you can use the files under /sys/firmware/acpi/interrupts/ > > to see what GPEs are activated by the wakeup events. > > Ok, before I put the host controller into D3 by echoing auto to > /sys/bus/pci/devices/0000:00:14.0/power/control, catting those files in > /sys/firmware/acpi/interrupts/ shows all zeros (and some enabled GPEs). > > After I enable runtime PM for the PCI device, wait for it to go into D3, > and then plug a new USB host controller into an external hub under xHCI, > I see the count in the file gpe0D increase: > > sarah@talon:/sys/firmware/acpi/interrupts$ cat gpe0D > 645925 disabled Well, apparently, the GPE is disabled, although it should be enabled at this point if it is supposed to be a wakeup GPE for the controller. > But the host controller is never brought out of D3, and the port status > change events was never reported. The dmesg from the run is attached, > with some additional debugging I added to the PCI and ACPI core. The > part where the host controller first goes into D3 is on line 3521. > > I'm starting to think that the ACPI tables for this platform are not > correct. The BIOS guys haven't let me know whether wake from D3 is > actually supported by the BIOS yet (this platform is still under > development). The disassembled ACPI tables are attached. Without looking at the tables at the moment (I'll do that later), I think that they are missing the information that GPE 0D is a wakeup GPE for the xHCI device. > In digging through the ACPI code, I noticed that acpi_bus_get_flags() > looks for the ACPI methods _PR0 or _PS0 and sets > device->flags.power_manageable to 1 if either of those methods are > successfully invoked. When I deassembled the ACPI tables, I didn't see > either method for any of the USB host controllers in the system. > device->flags.power_manageable is checked later when the runtime PM > system attempts to put the PCI device into a lower state, but it seems > to be ignored? Is it supposed to be ignored? Hmm, not really. I'll have a look at that later. > I'm wondering if both native PCIe PME and SCI PME generation are not > supported by the PCIe device, why does runtime PM put the xHCI host > controller into D3 when power/control is set to 'auto'? Because it doesn't require that the devices support remote wakeup to be put into low power states. User space may simply want to save energy by letting the device to go into D3 and it will wake it up later by writing "on" into power/control, for example. Thanks, Rafael -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
