[PATCH v7 5/8] phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the standalone i.MX8 PCIe PHY driver.

Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
Tested-by: Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx>
Reviewed-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
Tested-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
 drivers/phy/freescale/Kconfig              |   8 +
 drivers/phy/freescale/Makefile             |   1 +
 drivers/phy/freescale/phy-fsl-imx8m-pcie.c | 236 +++++++++++++++++++++
 3 files changed, 245 insertions(+)
 create mode 100644 drivers/phy/freescale/phy-fsl-imx8m-pcie.c

diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index 320630ffe3cd..c3669c28ea9f 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -14,3 +14,11 @@ config PHY_MIXEL_MIPI_DPHY
 	help
 	  Enable this to add support for the Mixel DSI PHY as found
 	  on NXP's i.MX8 family of SOCs.
+
+config PHY_FSL_IMX8M_PCIE
+	tristate "Freescale i.MX8M PCIE PHY"
+	depends on OF && HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to add support for the PCIE PHY as found on
+	  i.MX8M family of SOCs.
diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
index 1d02e3869b45..55d07c742ab0 100644
--- a/drivers/phy/freescale/Makefile
+++ b/drivers/phy/freescale/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_PHY_FSL_IMX8MQ_USB)	+= phy-fsl-imx8mq-usb.o
 obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY)	+= phy-fsl-imx8-mipi-dphy.o
+obj-$(CONFIG_PHY_FSL_IMX8M_PCIE)	+= phy-fsl-imx8m-pcie.o
diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
new file mode 100644
index 000000000000..f6502463d49a
--- /dev/null
+++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+#define IMX8MM_PCIE_PHY_CMN_REG061	0x184
+#define  ANA_PLL_CLK_OUT_TO_EXT_IO_EN	BIT(0)
+#define IMX8MM_PCIE_PHY_CMN_REG062	0x188
+#define  ANA_PLL_CLK_OUT_TO_EXT_IO_SEL	BIT(3)
+#define IMX8MM_PCIE_PHY_CMN_REG063	0x18C
+#define  AUX_PLL_REFCLK_SEL_SYS_PLL	GENMASK(7, 6)
+#define IMX8MM_PCIE_PHY_CMN_REG064	0x190
+#define  ANA_AUX_RX_TX_SEL_TX		BIT(7)
+#define  ANA_AUX_RX_TERM_GND_EN		BIT(3)
+#define  ANA_AUX_TX_TERM		BIT(2)
+#define IMX8MM_PCIE_PHY_CMN_REG065	0x194
+#define  ANA_AUX_RX_TERM		(BIT(7) | BIT(4))
+#define  ANA_AUX_TX_LVL			GENMASK(3, 0)
+#define IMX8MM_PCIE_PHY_CMN_REG75	0x1D4
+#define  PCIE_PHY_CMN_REG75_PLL_DONE	0x3
+#define PCIE_PHY_TRSV_REG5		0x414
+#define  PCIE_PHY_TRSV_REG5_GEN1_DEEMP	0x2D
+#define PCIE_PHY_TRSV_REG6		0x418
+#define  PCIE_PHY_TRSV_REG6_GEN2_DEEMP	0xF
+
+#define IMX8MM_GPR_PCIE_REF_CLK_SEL	GENMASK(25, 24)
+#define IMX8MM_GPR_PCIE_REF_CLK_PLL	FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x3)
+#define IMX8MM_GPR_PCIE_REF_CLK_EXT	FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x2)
+#define IMX8MM_GPR_PCIE_AUX_EN		BIT(19)
+#define IMX8MM_GPR_PCIE_CMN_RST		BIT(18)
+#define IMX8MM_GPR_PCIE_POWER_OFF	BIT(17)
+#define IMX8MM_GPR_PCIE_SSC_EN		BIT(16)
+#define IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE	BIT(9)
+
+struct imx8_pcie_phy {
+	void __iomem		*base;
+	struct clk		*clk;
+	struct phy		*phy;
+	struct regmap		*iomuxc_gpr;
+	struct reset_control	*reset;
+	u32			refclk_pad_mode;
+	u32			tx_deemph_gen1;
+	u32			tx_deemph_gen2;
+	bool			clkreq_unused;
+};
+
+static int imx8_pcie_phy_init(struct phy *phy)
+{
+	int ret;
+	u32 val, pad_mode;
+	struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
+
+	reset_control_assert(imx8_phy->reset);
+
+	pad_mode = imx8_phy->refclk_pad_mode;
+	/* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
+			   imx8_phy->clkreq_unused ?
+			   0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_AUX_EN,
+			   IMX8MM_GPR_PCIE_AUX_EN);
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_POWER_OFF, 0);
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_SSC_EN, 0);
+
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_REF_CLK_SEL,
+			   pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
+			   IMX8MM_GPR_PCIE_REF_CLK_EXT :
+			   IMX8MM_GPR_PCIE_REF_CLK_PLL);
+	usleep_range(100, 200);
+
+	/* Do the PHY common block reset */
+	regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
+			   IMX8MM_GPR_PCIE_CMN_RST,
+			   IMX8MM_GPR_PCIE_CMN_RST);
+	usleep_range(200, 500);
+
+	if (pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT) {
+		/* Configure the pad as input */
+		val = readl(imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061);
+		writel(val & ~ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061);
+	} else if (pad_mode == IMX8_PCIE_REFCLK_PAD_OUTPUT) {
+		/* Configure the PHY to output the refclock via pad */
+		writel(ANA_PLL_CLK_OUT_TO_EXT_IO_EN,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG061);
+		writel(ANA_PLL_CLK_OUT_TO_EXT_IO_SEL,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG062);
+		writel(AUX_PLL_REFCLK_SEL_SYS_PLL,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG063);
+		val = ANA_AUX_RX_TX_SEL_TX | ANA_AUX_TX_TERM;
+		writel(val | ANA_AUX_RX_TERM_GND_EN,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG064);
+		writel(ANA_AUX_RX_TERM | ANA_AUX_TX_LVL,
+		       imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG065);
+	}
+
+	/* Tune PHY de-emphasis setting to pass PCIe compliance. */
+	if (imx8_phy->tx_deemph_gen1)
+		writel(imx8_phy->tx_deemph_gen1,
+		       imx8_phy->base + PCIE_PHY_TRSV_REG5);
+	if (imx8_phy->tx_deemph_gen2)
+		writel(imx8_phy->tx_deemph_gen2,
+		       imx8_phy->base + PCIE_PHY_TRSV_REG6);
+
+	reset_control_deassert(imx8_phy->reset);
+
+	/* Polling to check the phy is ready or not. */
+	ret = readl_poll_timeout(imx8_phy->base + IMX8MM_PCIE_PHY_CMN_REG75,
+				 val, val == PCIE_PHY_CMN_REG75_PLL_DONE,
+				 10, 20000);
+	return ret;
+}
+
+static int imx8_pcie_phy_power_on(struct phy *phy)
+{
+	struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
+
+	return clk_prepare_enable(imx8_phy->clk);
+}
+
+static int imx8_pcie_phy_power_off(struct phy *phy)
+{
+	struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
+
+	clk_disable_unprepare(imx8_phy->clk);
+
+	return 0;
+}
+
+static const struct phy_ops imx8_pcie_phy_ops = {
+	.init		= imx8_pcie_phy_init,
+	.power_on	= imx8_pcie_phy_power_on,
+	.power_off	= imx8_pcie_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int imx8_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct imx8_pcie_phy *imx8_phy;
+	struct resource *res;
+
+	imx8_phy = devm_kzalloc(dev, sizeof(*imx8_phy), GFP_KERNEL);
+	if (!imx8_phy)
+		return -ENOMEM;
+
+	/* get PHY refclk pad mode */
+	of_property_read_u32(np, "fsl,refclk-pad-mode",
+			     &imx8_phy->refclk_pad_mode);
+
+	if (of_property_read_u32(np, "fsl,tx-deemph-gen1",
+				 &imx8_phy->tx_deemph_gen1))
+		imx8_phy->tx_deemph_gen1 = 0;
+
+	if (of_property_read_u32(np, "fsl,tx-deemph-gen2",
+				 &imx8_phy->tx_deemph_gen2))
+		imx8_phy->tx_deemph_gen2 = 0;
+
+	if (of_property_read_bool(np, "fsl,clkreq-unsupported"))
+		imx8_phy->clkreq_unused = true;
+	else
+		imx8_phy->clkreq_unused = false;
+
+	imx8_phy->clk = devm_clk_get(dev, "ref");
+	if (IS_ERR(imx8_phy->clk)) {
+		dev_err(dev, "failed to get imx pcie phy clock\n");
+		return PTR_ERR(imx8_phy->clk);
+	}
+
+	/* Grab GPR config register range */
+	imx8_phy->iomuxc_gpr =
+		 syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+	if (IS_ERR(imx8_phy->iomuxc_gpr)) {
+		dev_err(dev, "unable to find iomuxc registers\n");
+		return PTR_ERR(imx8_phy->iomuxc_gpr);
+	}
+
+	imx8_phy->reset = devm_reset_control_get_exclusive(dev, "pciephy");
+	if (IS_ERR(imx8_phy->reset)) {
+		dev_err(dev, "Failed to get PCIEPHY reset control\n");
+		return PTR_ERR(imx8_phy->reset);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	imx8_phy->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(imx8_phy->base))
+		return PTR_ERR(imx8_phy->base);
+
+	imx8_phy->phy = devm_phy_create(dev, NULL, &imx8_pcie_phy_ops);
+	if (IS_ERR(imx8_phy->phy))
+		return PTR_ERR(imx8_phy->phy);
+
+	phy_set_drvdata(imx8_phy->phy, imx8_phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id imx8_pcie_phy_of_match[] = {
+	{.compatible = "fsl,imx8mm-pcie-phy",},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, imx8_pcie_phy_of_match);
+
+static struct platform_driver imx8_pcie_phy_driver = {
+	.probe	= imx8_pcie_phy_probe,
+	.driver = {
+		.name	= "imx8-pcie-phy",
+		.of_match_table	= imx8_pcie_phy_of_match,
+	}
+};
+module_platform_driver(imx8_pcie_phy_driver);
+
+MODULE_DESCRIPTION("FSL IMX8 PCIE PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.1




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux