PCIe PMU Root Complex Integrated End Point(RCiEP) device is supported on HiSilicon HIP09 platform. Document it to provide guidance on how to use it. Reviewed-by: John Garry <john.garry@xxxxxxxxxx> Signed-off-by: Qi Liu <liuqi115@xxxxxxxxxx> --- .../admin-guide/perf/hisi-pcie-pmu.rst | 106 ++++++++++++++++++ 1 file changed, 106 insertions(+) create mode 100644 Documentation/admin-guide/perf/hisi-pcie-pmu.rst diff --git a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst new file mode 100644 index 000000000000..294ebbdb22af --- /dev/null +++ b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst @@ -0,0 +1,106 @@ +================================================ +HiSilicon PCIe Performance Monitoring Unit (PMU) +================================================ + +On Hip09, HiSilicon PCIe Performance Monitoring Unit (PMU) could monitor +bandwidth, latency, bus utilization and buffer occupancy data of PCIe. + +Each PCIe Core has a PMU to monitor multi Root Ports of this PCIe Core and +all Endpoints downstream these Root Ports. + + +HiSilicon PCIe PMU driver +========================= + +The PCIe PMU driver registers a perf PMU with the name of its sicl-id and PCIe +Core id.:: + + /sys/bus/event_source/hisi_pcie<sicl>_<core> + +PMU driver provides description of available events and filter options in sysfs, +see /sys/bus/event_source/devices/hisi_pcie<sicl>_<core>. + +The "format" directory describes all formats of the config (events) and config1 +(filter options) fields of the perf_event_attr structure. The "events" directory +describes all documented events shown in perf list. + +The "identifier" sysfs file allows users to identify the version of the +PMU hardware device. + +The "bus" sysfs file allows users to get the bus number of Root Ports +monitored by PMU. + +Example usage of perf:: + + $# perf list + hisi_pcie0_0/rx_mwr_latency/ [kernel PMU event] + hisi_pcie0_0/rx_mwr_cnt/ [kernel PMU event] + ------------------------------------------ + + $# perf stat -e hisi_pcie0_0/rx_mwr_latency/ + $# perf stat -e hisi_pcie0_0/rx_mwr_cnt/ + $# perf stat -g -e hisi_pcie0_0/rx_mwr_latency/ -e hisi_pcie0_0/rx_mwr_cnt/ + +The current driver does not support sampling. So "perf record" is unsupported. +Also attach to a task is unsupported for PCIe PMU. + +Filter options +-------------- + +1. Target filter +PMU could only monitor the performance of traffic downstream target Root Ports +or downstream target Endpoint. PCIe PMU driver support "port" and "bdf" +interfaces for users, and these two interfaces aren't supported at the same +time. + +-port +"port" filter can be used in all PCIe PMU events, target Root Port can be +selected by configuring the 16-bits-bitmap "port". Multi ports can be selected +for AP-layer-events, and only one port can be selected for TL/DL-layer-events. + +For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap +should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes), +bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mwr_latency,port=0x1/ sleep 5 + +-bdf + +"bdf" filter can only be used in bandwidth events, target Endpoint is selected +by configuring BDF to "bdf". Counter only counts the bandwidth of message +requested by target Endpoint. + +For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,bdf=0x3900/ sleep 5 + +2. Trigger filter +Event statistics start when the first time TLP length is greater/smaller +than trigger condition. You can set the trigger condition by writing "trig_len", +and set the trigger mode by writing "trig_mode". This filter can only be used +in bandwidth events. + +For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0" +means statistics start when TLP length > trigger condition, "trig_mode=1" +means start when TLP length < condition. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5 + +3. Threshold filter +Counter counts when TLP length within the specified range. You can set the +threshold by writing "thr_len", and set the threshold mode by writing +"thr_mode". This filter can only be used in bandwidth events. + +For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means +counter counts when TLP length >= threshold, and "thr_mode=1" means counts +when TLP length < threshold. + +Example usage of perf:: + + $# perf stat -e hisi_pcie0_0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5 -- 2.33.0
