On 21-11-22 15:11:31, Jonathan Cameron wrote:
> On Fri, 19 Nov 2021 16:02:32 -0800
> Ben Widawsky <ben.widawsky@xxxxxxxxx> wrote:
>
> > The expectation is that the mailbox interface ready bit is the first
> > step in access through the mailbox interface.
>
> Reword this? Perhaps
> "The expectation is that the mailbox interface ready bit will be set
> at the start of any access through the mailbox interface."
>
> > Therefore, waiting for the
> > doorbell busy bit to be clear would imply that the mailbox interface is
> > ready. The original driver implementation used the doorbell timeout for
> > the Mailbox Interface Ready bit to piggyback off of, since the latter
> > doesn't have a defined timeout (introduced in 8adaf747c9f0 ("cxl/mem:
> > Find device capabilities"), a timeout has since been defined with an ECN
> > to the 2.0 spec). With the current driver waiting for mailbox interface
> > ready as a part of probe() it's no longer necessary to use the
> > piggyback.
> >
> > With the piggybacking no longer necessary it doesn't make sense to check
> > doorbell status when acquiring the mailbox. It will be checked during
> > the normal mailbox exchange protocol.
> >
> > Signed-off-by: Ben Widawsky <ben.widawsky@xxxxxxxxx>
> Trivial comment inline - with that fixed either by calling it out, or by
> pulling it out of this patch.
>
> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
>
> > ---
> > This patch did not exist in RFCv2
> > ---
> > drivers/cxl/pci.c | 25 ++++++-------------------
> > 1 file changed, 6 insertions(+), 19 deletions(-)
> >
> > diff --git a/drivers/cxl/pci.c b/drivers/cxl/pci.c
> > index 2cef9fec8599..869b4fc18e27 100644
> > --- a/drivers/cxl/pci.c
> > +++ b/drivers/cxl/pci.c
> > @@ -221,27 +221,14 @@ static int cxl_pci_mbox_get(struct cxl_dev_state *cxlds)
> >
> > /*
> > * XXX: There is some amount of ambiguity in the 2.0 version of the spec
> > - * around the mailbox interface ready (8.2.8.5.1.1). The purpose of the
> > + * around the mailbox interface ready (8.2.8.5.1.1). The purpose of the
>
> Whilst it's trivial, I'd prefer white space cleanup in separate patches.
> I guess this one is obvious enough to just call out in the patch description
> though.
>
Okay. I'll keep this in mind for the future, and just fixup the commit messages
with your suggestion and this, now.
Thanks.
Ben
> > * bit is to allow firmware running on the device to notify the driver
> > - * that it's ready to receive commands. It is unclear if the bit needs
> > - * to be read for each transaction mailbox, ie. the firmware can switch
> > - * it on and off as needed. Second, there is no defined timeout for
> > - * mailbox ready, like there is for the doorbell interface.
> > - *
> > - * Assumptions:
> > - * 1. The firmware might toggle the Mailbox Interface Ready bit, check
> > - * it for every command.
> > - *
> > - * 2. If the doorbell is clear, the firmware should have first set the
> > - * Mailbox Interface Ready bit. Therefore, waiting for the doorbell
> > - * to be ready is sufficient.
> > + * that it's ready to receive commands. The spec does not clearly define
> > + * under what conditions the bit may get set or cleared. As of the 2.0
> > + * base specification there was no defined timeout for mailbox ready,
> > + * like there is for the doorbell interface. This was fixed with an ECN,
> > + * but it's possible early devices implemented this before the ECN.
> > */
> > - rc = cxl_pci_mbox_wait_for_doorbell(cxlds);
> > - if (rc) {
> > - dev_warn(dev, "Mailbox interface not ready\n");
> > - goto out;
> > - }
> > -
> > md_status = readq(cxlds->regs.memdev + CXLMDEV_STATUS_OFFSET);
> > if (!(md_status & CXLMDEV_MBOX_IF_READY && CXLMDEV_READY(md_status))) {
> > dev_err(dev, "mbox: reported doorbell ready, but not mbox ready\n");
>
