On 7/1/2011 12:02 PM, Jon Mason wrote:
On Fri, Jul 1, 2011 at 1:30 PM, Richard A Lary<rlary@xxxxxxxxxxxxxxxxxx> wrote:
On 7/1/2011 8:24 AM, Jon Mason wrote:
I recently sent out a number of patches to migrate drivers calling
`pci_find_capability(pdef, PCI_CAP_ID_EXP)` to pci_pcie_cap. This
function takes uses a PCI-E capability offset that was determined by
calling pci_find_capability during the PCI bus walking. In response
to one of the patches, James Smart posted:
"The reason is due to an issue on PPC platforms whereby use of
"pdev->is_pcie" and pci_is_pcie() will erroneously fail under some
conditions, but explicit search for the capability struct via
pci_find_capability() is always successful. I expect this to be due
a shadowing of pci config space in the hal/platform that isn't
sufficiently built up. We detected this issue while testing AER/EEH,
and are functional only if the pci_find_capability() option is used."
See http://marc.info/?l=linux-scsi&m=130946649427828&w=2 for the whole
post.
Based on his description above pci_pcie_cap
andpci_find_capability(pdef, PCI_CAP_ID_EXP) should be functionally
equivalent. If this is not safe, then the PCI bus walking code is
most likely busted on EEH enabled PPC systems (and that is a BIG
problem). Can anyone confirm this is still an issue?
Jon,
I applied the following debug patch to lpfc driver in a 2.6.32 distro
kernel ( I had this one handy, I can try with mainline later today )
---
drivers/scsi/lpfc/lpfc_init.c | 10 10 + 0 - 0 !
1 file changed, 10 insertions(+)
Index: b/drivers/scsi/lpfc/lpfc_init.c
===================================================================
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -3958,6 +3958,16 @@ lpfc_enable_pci_dev(struct lpfc_hba *phb
pci_try_set_mwi(pdev);
pci_save_state(pdev);
+ printk(KERN_WARNING "pcicap: is_pcie=%x pci_cap=%x pcie_type=%x\n",
+ pdev->is_pcie,
+ pdev->pcie_cap,
+ pdev->pcie_type);
+
+ if (pci_is_pcie(pdev))
+ printk(KERN_WARNING "pcicap: true\n");
+ else
+ printk(KERN_WARNING "pcicap: false\n");
+
/* PCIe EEH recovery on powerpc platforms needs fundamental reset */
if (pci_find_capability(pdev, PCI_CAP_ID_EXP))
pdev->needs_freset = 1;
This is output upon driver load on an IBM Power 7 model 8233-E8B server.
dmesg | grep pcicap
Linux version 2.6.32.42-pcicap-ppc64 (geeko@buildhost) (gcc version 4.3.4
[gcc-4_3-branch revision 152973] (SUSE Linux) ) #1 SMP Fri Jul 1 09:31:27
PDT 2011
pcicap: is_pcie=0 pci_cap=0 pcie_type=0
pcicap: false
pcicap: is_pcie=0 pci_cap=0 pcie_type=0
pcicap: false
pcicap: is_pcie=0 pci_cap=0 pcie_type=0
pcicap: false
pcicap: is_pcie=0 pci_cap=0 pcie_type=0
pcicap: false
It would appear that the pcie information is not set in pci_dev structure
for
this device at the time the driver is being initialized during boot.
Thanks for trying this. Can you confirm that the other devices in the
system have this issue as well (or show that it is isolated to the lpr
device)? You can add printks in set_pcie_port_type() to verify what
is being set on bus walking and to see when it is being called with
respect to when it is being populated by firmware.
Jon,
I will give this suggestion a try and post results
-rich
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
