Re: [PATCH V6] PCI: rcar: Add L1 link state fix into data abort hook

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jul 27, 2021 at 07:08:17PM +0200, Marek Vasut wrote:
> On 7/26/21 7:49 PM, Bjorn Helgaas wrote:
> > On Mon, Jul 26, 2021 at 04:47:54PM +0200, Geert Uytterhoeven wrote:
> [...]
> > > > > The R-Car PCIe controller is capable of handling L0s/L1 link states.
> > > > > While the controller can enter and exit L0s link state, and exit L1
> > > > > link state, without any additional action from the driver, to enter
> > > > > L1 link state, the driver must complete the link state transition by
> > > > > issuing additional commands to the controller.
> > > > > 
> > > > > The problem is, this transition is not atomic. The controller sets
> > > > > PMEL1RX bit in PMSR register upon reception of PM_ENTER_L1 DLLP from
> > > > > the PCIe card, but then the controller enters some sort of inbetween
> > > > > state. The driver must detect this condition and complete the link
> > > > > state transition, by setting L1IATN bit in PMCTLR and waiting for
> > > > > the link state transition to complete.
> > > > > 
> > > > > If a PCIe access happens inside this window, where the controller
> > > > > is between L0 and L1 link states, the access generates a fault and
> > > > > the ARM 'imprecise external abort' handler is invoked.
> > > > > 
> > > > > Just like other PCI controller drivers, here we hook the fault handler,
> > > > > perform the fixup to help the controller enter L1 link state, and then
> > > > > restart the instruction which triggered the fault. Since the controller
> > > > > is in L1 link state now, the link can exit from L1 link state to L0 and
> > > > > successfully complete the access.
> > > > > 
> > > > > While it was suggested to disable L1 link state support completely on
> > > > > the controller level, this would not prevent the L1 link state entry
> > > > > initiated by the link partner. This happens e.g. in case a PCIe card
> > > > > enters D3Hot state, which could be initiated from pci_set_power_state()
> > > > > if the card indicates D3Hot support, which in turn means link must enter
> > > > > L1 state. So instead, fix up the L1 link state after all.
> > > > > 
> > > > > Note that this fixup is applicable only to Aarch32 R-Car controllers,
> > > > > the Aarch64 R-Car perform the same fixup in TFA, see TFA commit [1]
> > > > > 0969397f2 ("rcar_gen3: plat: Prevent PCIe hang during L1X config access")
> > > > > [1] https://github.com/ARM-software/arm-trusted-firmware/commit/0969397f295621aa26b3d14b76dd397d22be58bf
> > > > 
> > > > This patch is horribly ugly but it's working around a horrible
> > > > hardware problem, and I don't have any better suggestions, so I guess
> > > > we don't really have much choice.
> > > > 
> > > > I do think the commit log is a bit glib:
> > > > 
> > > >    - "The R-Car PCIe controller is capable of handling L0s/L1 link
> > > >      states."  AFAICT every PCIe device is required to handle L0 and L1
> > > >      without software assistance.  So saying R-Car is "capable" puts a
> > > >      better face on this than seems warranted.
> > > > 
> > > >      L0s doesn't seem relevant at all; at least it doesn't seem to play
> > > >      a role in the patch.  There's no such thing as "returning to L0s"
> > > >      as mentioned in the comment below; L0s is only reachable from L0.
> > > >      Returns from L1 only go to L0 (PCIe r5.0, fig 5-1).
> > > > 
> > > >    - "The problem is, this transition is not atomic."  I think the
> > > >      *problem* is the hardware is broken in the first place.  This
> > > >      transition is supposed to be invisible to software.
> > > > 
> > > >    - "Just like other PCI controller drivers ..." suggests that this is
> > > >      an ordinary situation that we shouldn't be concerned about.  This
> > > >      patch may be the best we can do to work around a bad hardware
> > > >      defect, but it's definitely not ordinary.
> > > > 
> > > >      I think the other hook_fault_code() uses are for reporting
> > > >      legitimate PCIe errors, which most controllers log and turn
> > > >      into ~0 data responses without generating an abort or machine
> > > >      check, not things caused by hardware defects, so they're not
> > > >      really comparable.
> > > > 
> > > > Has Renesas documented this as an erratum?  Will future devices
> > > > require additions to rcar_pcie_abort_handler_of_match[]?
> > > > 
> > > > It'd be nice if the commit log mentioned the user-visible effect of
> > > > this problem.  I guess it does mention external aborts -- I assume you
> > > > see those when downstream devices go to D3hot or when ASPM puts the
> > > > link in L1?  And the abort results in a reboot?
> > > > 
> > > > To be clear, I'm not objecting to the patch.  It's a hardware problem
> > > > and we should work around it as best we can.
> > > 
> > > Cool! So what's missing for this patch, which we have been polishing
> > > for almost one year, to be applied, so innocent people can no longer
> > > lock up an R-Car system just by inserting an ubiquitous Intel Ethernet
> > > card, and suspending the system?
> > 
> > Nothing missing from my point of view, so if Lorenzo is OK with it,
> > he'll apply it.  If I were applying it, I would make the commit log
> > something like this:
> > 
> >    When the link is in L1, hardware should return it to L0
> >    automatically whenever a transaction targets a component on the
> >    other end of the link (PCIe r5.0, sec 5.2).
> > 
> >    The R-Car PCIe controller doesn't handle this transition correctly.
> >    If the link is not in L0, an MMIO transaction targeting a downstream
> >    device fails, and the controller reports an ARM imprecise external
> >    abort.
> > 
> >    Work around this by hooking the abort handler so the driver can
> >    detect this situation and help the hardware complete the link state
> >    transition.
> > 
> >    When the R-Car controller receives a PM_ENTER_L1 DLLP from the
> >    downstream component, it sets PMEL1RX bit in PMSR register, but then
> >    the controller enters some sort of in-between state.  A subsequent
> >    MMIO transaction will fail, resulting in the external abort.  The
> >    abort handler detects this condition and completes the link state
> >    transition by setting the L1IATN bit in PMCTLR and waiting for the
> >    link state transition to complete.
> 
> OK, should I submit V7 and just copy-paste this commit message in, or wait
> for Lorenzo to provide clear direction ?

Hi Marek,

may I ask you please to update the log as Bjorn requested, add a timeout
in the trap handler to avoid an infinite loop on failure and repost a v7
?

I will merge it straight away sorry for all this back and forth.

Thanks,
Lorenzo

> > I assume that on the PCIe side, there must be an error like
> > Unsupported Request or Malformed TLP, and the R-Car controller is
> > logging that and turning it into the ARM external abort?
> > 
> > I didn't see a clear response to Pali's question about what happens if
> > there's no MMIO access, e.g., what if the downstream device initiates
> > a DMA or MSI transaction?
> 
> If the link is in this state, the packet won't reach the root complex, so
> nothing happens. And I don't see a good way to fix that option.



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux