On Sun, Jun 5, 2011 at 6:36 PM, Bjorn Helgaas <bhelgaas@xxxxxxxxxx> wrote: > On Sun, Jun 5, 2011 at 5:57 AM, Carl Karsten <carl@xxxxxxxxxxxxxxxxx> wrote: >> I am wondering why I see a difference between 2 similar setups: >> >> I have 2 laptops, ubuntu 2.6.39-3-generic on both. >> pciehp is included, acpiphp built but not inserted by default. >> >> HP EliteBook 8530w (KS051UA#ABA) >> HP Pavilion dv6700 Notebook PC (KC300UA#ABA) >> >> On the EliteBook, hotplug works: lspci entries come and go, modules >> un/load, udev reports add/remove. good. >> >> On the Pavilion, if I load acpiphp (via /etc/modules), hotplug works. >> If I don't load any additional modules hotplug does not work: insert >> card - nothing in syslog, lspci, udev. If a card is in the slot when >> the kernel loads, it shows in syslog, lscpi and the drivers get >> loaded. If I pull it out, nothing changes: still listed in lspci, >> modules still loaded, dev nodes still around. >> >> Here is some logs lines from Pavilion: >> >> stock module, doesn't work: >> [ 0.560575] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 >> [ 0.560605] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > > It might be useful to see the entire dmesg log and the "lspci -vv" > output from the Pavilion. > [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.39-3-generic (buildd@allspice) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.0-10ubuntu1) ) #10-Ubuntu SMP Sat May 28 05:46:37 UTC 2011 (Ubuntu 2.6.39-3.10-generic 2.6.39) [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-2.6.39-3-generic root=UUID=7a5a1e63-8e75-443f-b732-522709dd36d6 ro quiet splash vt.handoff=7 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable) [ 0.000000] BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007bf50000 (usable) [ 0.000000] BIOS-e820: 000000007bf50000 - 000000007bf65000 (ACPI data) [ 0.000000] BIOS-e820: 000000007bf65000 - 000000007bf66000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007bf66000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI present. [ 0.000000] DMI: Hewlett-Packard HP Pavilion dv6700 Notebook PC /30CF, BIOS F.27 01/11/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x7bf50 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-D3FFF write-protect [ 0.000000] D4000-E3FFF uncachable [ 0.000000] E4000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 0000000000 mask FF80000000 write-back [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] found SMP MP-table at [ffff8800000f8220] f8220 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-000000007bf50000 [ 0.000000] 0000000000 - 007be00000 page 2M [ 0.000000] 007be00000 - 007bf50000 page 4k [ 0.000000] kernel direct mapping tables up to 7bf50000 @ 7bf4c000-7bf50000 [ 0.000000] RAMDISK: 3652e000 - 3728f000 [ 0.000000] ACPI: RSDP 00000000000f8250 00024 (v02 PTLTD ) [ 0.000000] ACPI: XSDT 000000007bf5c0fb 0006C (v01 HPQOEM SLIC-MPC 06040000 LTP 00000000) [ 0.000000] ACPI: FACP 000000007bf649ba 000F4 (v03 NVIDIA MCP67-M 06040000 PTL_ 000F4240) [ 0.000000] ACPI: DSDT 000000007bf5c167 087DF (v01 NVIDIA MCP67 06040000 MSFT 03000000) [ 0.000000] ACPI: FACS 000000007bf65fc0 00040 [ 0.000000] ACPI: TCPA 000000007bf64aae 00032 (v01 Phoeni x 06040000 TL 00000000) [ 0.000000] ACPI: SRAT 000000007bf64ae0 000A0 (v01 AMD HAMMER 06040000 AMD 00000001) [ 0.000000] ACPI: SSDT 000000007bf64b80 00206 (v01 PTLTD POWERNOW 06040000 LTP 00000001) [ 0.000000] ACPI: MCFG 000000007bf64d86 0003C (v01 PTLTD MCFG 06040000 LTP 00000000) [ 0.000000] ACPI: HPET 000000007bf64dc2 00038 (v01 PTLTD HPETTBL 06040000 LTP 00000001) [ 0.000000] ACPI: APIC 000000007bf64dfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000) [ 0.000000] ACPI: BOOT 000000007bf64e62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001) [ 0.000000] ACPI: SLIC 000000007bf64e8a 00176 (v01 HPQOEM SLIC-MPC 06040000 LTP 00000001) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] SRAT: PXM 0 -> APIC 0x00 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 0x01 -> Node 0 [ 0.000000] SRAT: Node 0 PXM 0 0-a0000 [ 0.000000] SRAT: Node 0 PXM 0 100000-80000000 [ 0.000000] NUMA: Node 0 [0,a0000) + [100000,80000000) -> [0,7bf50000) [ 0.000000] NUMA: Using 63 for the hash shift. [ 0.000000] Initmem setup node 0 0000000000000000-000000007bf50000 [ 0.000000] NODE_DATA [000000007bf47000 - 000000007bf4bfff] [ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880079600000-ffff88007b1fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009e [ 0.000000] 0: 0x00000100 -> 0x0007bf50 [ 0.000000] On node 0 totalpages: 507614 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3921 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 6886 pages used for memmap [ 0.000000] DMA32 zone: 496746 pages, LIFO batch:31 [ 0.000000] Detected use of extended apic ids on hypertransport bus [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000 [ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007bc00000 s85120 r8192 d21376 u1048576 [ 0.000000] pcpu-alloc: s85120 r8192 d21376 u1048576 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 500667 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.39-3-generic root=UUID=7a5a1e63-8e75-443f-b732-522709dd36d6 ro quiet splash vt.handoff=7 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Node 0: aperture @ 9ffc000000 size 32 MB [ 0.000000] Aperture beyond 4GB. Ignoring. [ 0.000000] Memory: 1974356k/2030912k available (6067k kernel code, 456k absent, 56100k reserved, 4894k data, 988k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:16640 nr_irqs:512 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] vt handoff: transparent VT on vt#7 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 16777216 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2000.545 MHz processor. [ 0.000000] Marking TSC unstable due to TSCs unsynchronized [ 0.010006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4001.09 BogoMIPS (lpj=20005450) [ 0.010012] pid_max: default: 32768 minimum: 301 [ 0.010045] Security Framework initialized [ 0.010063] AppArmor: AppArmor initialized [ 0.010065] Yama: becoming mindful. [ 0.010356] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.011539] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.012139] Mount-cache hash table entries: 256 [ 0.012297] Initializing cgroup subsys ns [ 0.012301] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.012305] Initializing cgroup subsys cpuacct [ 0.012311] Initializing cgroup subsys memory [ 0.012321] Initializing cgroup subsys devices [ 0.012324] Initializing cgroup subsys freezer [ 0.012326] Initializing cgroup subsys net_cls [ 0.012328] Initializing cgroup subsys blkio [ 0.012337] Initializing cgroup subsys perf_event [ 0.012370] tseg: 007bf80000 [ 0.012373] CPU: Physical Processor ID: 0 [ 0.012375] CPU: Processor Core ID: 0 [ 0.012377] mce: CPU supports 5 MCE banks [ 0.012389] using C1E aware idle routine [ 0.014094] ACPI: Core revision 20110316 [ 0.030014] ftrace: allocating 25498 entries in 100 pages [ 0.040098] Setting APIC routing to flat [ 0.040566] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.146817] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02 [ 0.150000] Performance Events: AMD PMU driver. [ 0.150000] ... version: 0 [ 0.150000] ... bit width: 48 [ 0.150000] ... generic registers: 4 [ 0.150000] ... value mask: 0000ffffffffffff [ 0.150000] ... max period: 00007fffffffffff [ 0.150000] ... fixed-purpose events: 0 [ 0.150000] ... event mask: 000000000000000f [ 0.150000] Booting Node 0, Processors #1 Ok. [ 0.150000] smpboot cpu 1: start_ip = 99000 [ 0.020000] System has AMD C1E enabled [ 0.020000] Switch to broadcast mode on CPU1 [ 0.300130] Brought up 2 CPUs [ 0.300133] Total of 2 processors activated (8001.46 BogoMIPS). [ 0.300573] Switch to broadcast mode on CPU0 [ 0.300573] devtmpfs: initialized [ 0.300573] PM: Registering ACPI NVS region at 7bf65000 (4096 bytes) [ 0.301058] print_constraints: dummy: [ 0.301093] Time: 17:30:53 Date: 06/06/11 [ 0.301142] NET: Registered protocol family 16 [ 0.301182] Trying to unpack rootfs image as initramfs... [ 0.301305] node 0 link 0: io port [1000, fffff] [ 0.301309] TOM: 0000000080000000 aka 2048M [ 0.301312] node 0 link 0: mmio [a0000, bffff] [ 0.301315] node 0 link 0: mmio [80000000, dfffffff] [ 0.301318] node 0 link 0: mmio [e0000000, efffffff] [ 0.301321] node 0 link 0: mmio [f0000000, fe0bffff] [ 0.301324] bus: [00, ff] on node 0 link 0 [ 0.301327] bus: 00 index 0 [io 0x0000-0xffff] [ 0.301330] bus: 00 index 1 [mem 0x000a0000-0x000bffff] [ 0.301332] bus: 00 index 2 [mem 0x80000000-0xfcffffffff] [ 0.301343] ACPI: bus type pci registered [ 0.301421] PCI: MMCONFIG for domain 0000 [bus 00-04] at [mem 0xe0000000-0xe04fffff] (base 0xe0000000) [ 0.301425] PCI: MMCONFIG at [mem 0xe0000000-0xe04fffff] reserved in E820 [ 0.301836] PCI: Using configuration type 1 for base access [ 0.310227] bio: create slab <bio-0> at 0 [ 0.311145] ACPI: EC: Look up EC in DSDT [ 0.313621] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.314393] ACPI: Interpreter enabled [ 0.314397] ACPI: (supports S0 S3 S4 S5) [ 0.314417] ACPI: Using IOAPIC for interrupt routing [ 0.314710] ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62 [ 0.314710] ACPI: No dock devices found. [ 0.314710] HEST: Table not found. [ 0.314710] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.314710] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.314710] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] [ 0.314710] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x000f0000-0x000fffff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff] [ 0.314710] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff] [ 0.314710] pci_root PNP0A08:00: address space collision: host bridge window [mem 0x000d0000-0x000d3fff] conflicts with reserved [mem 0x000d2000-0x000fffff] [ 0.314710] pci 0000:00:00.0: [10de:0547] type 0 class 0x000500 [ 0.314710] pci 0000:00:01.0: [10de:0548] type 0 class 0x000601 [ 0.314710] pci 0000:00:01.1: [10de:0542] type 0 class 0x000c05 [ 0.314710] pci 0000:00:01.1: reg 10: [io 0x3080-0x30bf] [ 0.314710] pci 0000:00:01.1: reg 20: [io 0x3040-0x307f] [ 0.314710] pci 0000:00:01.1: reg 24: [io 0x3000-0x303f] [ 0.314710] pci 0000:00:01.1: PME# supported from D3hot D3cold [ 0.314710] pci 0000:00:01.1: PME# disabled [ 0.314710] pci 0000:00:01.2: [10de:0541] type 0 class 0x000500 [ 0.314710] pci 0000:00:01.3: [10de:0543] type 0 class 0x000b40 [ 0.314710] pci 0000:00:01.3: reg 10: [mem 0xf6200000-0xf627ffff] [ 0.314710] pci 0000:00:02.0: [10de:055e] type 0 class 0x000c03 [ 0.314710] pci 0000:00:02.0: reg 10: [mem 0xf6486000-0xf6486fff] [ 0.314710] pci 0000:00:02.0: supports D1 D2 [ 0.314710] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:02.0: PME# disabled [ 0.314710] pci 0000:00:02.1: [10de:055f] type 0 class 0x000c03 [ 0.314710] pci 0000:00:02.1: reg 10: [mem 0xf6489000-0xf64890ff] [ 0.314710] pci 0000:00:02.1: supports D1 D2 [ 0.314710] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:02.1: PME# disabled [ 0.314710] pci 0000:00:04.0: [10de:055e] type 0 class 0x000c03 [ 0.314710] pci 0000:00:04.0: reg 10: [mem 0xf6487000-0xf6487fff] [ 0.314710] pci 0000:00:04.0: supports D1 D2 [ 0.314710] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:04.0: PME# disabled [ 0.314710] pci 0000:00:04.1: [10de:055f] type 0 class 0x000c03 [ 0.314710] pci 0000:00:04.1: reg 10: [mem 0xf6489400-0xf64894ff] [ 0.314710] pci 0000:00:04.1: supports D1 D2 [ 0.314710] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:04.1: PME# disabled [ 0.314710] pci 0000:00:06.0: [10de:0560] type 0 class 0x000101 [ 0.314710] pci 0000:00:06.0: reg 20: [io 0x30c0-0x30cf] [ 0.314710] pci 0000:00:07.0: [10de:055c] type 0 class 0x000403 [ 0.314710] pci 0000:00:07.0: reg 10: [mem 0xf6480000-0xf6483fff] [ 0.314710] pci 0000:00:07.0: PME# supported from D3hot D3cold [ 0.314710] pci 0000:00:07.0: PME# disabled [ 0.314710] pci 0000:00:08.0: [10de:0561] type 1 class 0x000604 [ 0.314710] pci 0000:00:09.0: [10de:0550] type 0 class 0x000101 [ 0.314710] pci 0000:00:09.0: reg 10: [io 0x30f0-0x30f7] [ 0.314710] pci 0000:00:09.0: reg 14: [io 0x30e4-0x30e7] [ 0.314710] pci 0000:00:09.0: reg 18: [io 0x30e8-0x30ef] [ 0.314710] pci 0000:00:09.0: reg 1c: [io 0x30e0-0x30e3] [ 0.314710] pci 0000:00:09.0: reg 20: [io 0x30d0-0x30df] [ 0.314710] pci 0000:00:09.0: reg 24: [mem 0xf6484000-0xf6485fff] [ 0.314710] pci 0000:00:0a.0: [10de:054c] type 0 class 0x000200 [ 0.314710] pci 0000:00:0a.0: reg 10: [mem 0xf6488000-0xf6488fff] [ 0.314710] pci 0000:00:0a.0: reg 14: [io 0x30f8-0x30ff] [ 0.314710] pci 0000:00:0a.0: reg 18: [mem 0xf6489c00-0xf6489cff] [ 0.314710] pci 0000:00:0a.0: reg 1c: [mem 0xf6489800-0xf648980f] [ 0.314710] pci 0000:00:0a.0: supports D1 D2 [ 0.314710] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:0a.0: PME# disabled [ 0.314710] pci 0000:00:0c.0: [10de:0563] type 1 class 0x000604 [ 0.314710] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:0c.0: PME# disabled [ 0.314710] pci 0000:00:0d.0: [10de:0563] type 1 class 0x000604 [ 0.314710] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:00:0d.0: PME# disabled [ 0.314710] pci 0000:00:12.0: [10de:0531] type 0 class 0x000300 [ 0.314710] pci 0000:00:12.0: reg 10: [mem 0xf5000000-0xf5ffffff] [ 0.314710] pci 0000:00:12.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.314710] pci 0000:00:12.0: reg 1c: [mem 0xf4000000-0xf4ffffff 64bit] [ 0.314710] pci 0000:00:12.0: reg 30: [mem 0x00000000-0x0001ffff pref] [ 0.314710] pci 0000:00:18.0: [1022:1100] type 0 class 0x000600 [ 0.314710] pci 0000:00:18.1: [1022:1101] type 0 class 0x000600 [ 0.314710] pci 0000:00:18.2: [1022:1102] type 0 class 0x000600 [ 0.314710] pci 0000:00:18.3: [1022:1103] type 0 class 0x000600 [ 0.314710] pci 0000:02:05.0: [1180:0832] type 0 class 0x000c00 [ 0.314710] pci 0000:02:05.0: proprietary Ricoh MMC controller disabled (via firewire function) [ 0.314710] pci 0000:02:05.0: MMC cards are now supported by standard SDHCI controller [ 0.314710] pci 0000:02:05.0: reg 10: [mem 0xf6100000-0xf61007ff] [ 0.314710] pci 0000:02:05.0: supports D1 D2 [ 0.314710] pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:02:05.0: PME# disabled [ 0.314710] pci 0000:02:05.1: [1180:0822] type 0 class 0x000805 [ 0.314710] pci 0000:02:05.1: reg 10: [mem 0xf6100800-0xf61008ff] [ 0.314710] pci 0000:02:05.1: supports D1 D2 [ 0.314710] pci 0000:02:05.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:02:05.1: PME# disabled [ 0.314710] pci 0000:02:05.2: [1180:0592] type 0 class 0x000880 [ 0.314710] pci 0000:02:05.2: reg 10: [mem 0xf6101000-0xf61010ff] [ 0.314710] pci 0000:02:05.2: supports D1 D2 [ 0.314710] pci 0000:02:05.2: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:02:05.2: PME# disabled [ 0.314710] pci 0000:02:05.3: [1180:0852] type 0 class 0x000880 [ 0.314710] pci 0000:02:05.3: reg 10: [mem 0xf6101400-0xf61014ff] [ 0.314710] pci 0000:02:05.3: supports D1 D2 [ 0.314710] pci 0000:02:05.3: PME# supported from D0 D1 D2 D3hot D3cold [ 0.314710] pci 0000:02:05.3: PME# disabled [ 0.314710] pci 0000:00:08.0: PCI bridge to [bus 02-02] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [io 0xf000-0x0000] (disabled) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0xf6100000-0xf61fffff] [ 0.314710] pci 0000:00:08.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.314710] pci 0000:00:08.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000cc000-0x000cffff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000ec000-0x000effff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x000f0000-0x000fffff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode) [ 0.314710] pci 0000:00:08.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode) [ 0.314710] pci 0000:00:0c.0: PCI bridge to [bus 04-05] [ 0.314710] pci 0000:00:0c.0: bridge window [io 0x4000-0x4fff] [ 0.314710] pci 0000:00:0c.0: bridge window [mem 0xf2000000-0xf3ffffff] [ 0.314710] pci 0000:00:0c.0: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref] [ 0.314710] pci 0000:03:00.0: [168c:001c] type 0 class 0x000200 [ 0.314710] pci 0000:03:00.0: reg 10: [mem 0xf6000000-0xf600ffff 64bit] [ 0.314710] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.314710] pci 0000:00:0d.0: PCI bridge to [bus 03-03] [ 0.314710] pci 0000:00:0d.0: bridge window [io 0xf000-0x0000] (disabled) [ 0.314710] pci 0000:00:0d.0: bridge window [mem 0xf6000000-0xf60fffff] [ 0.314710] pci 0000:00:0d.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 0.314710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.314710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] [ 0.314710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT] [ 0.314710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT] [ 0.314710] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 0.314710] Unable to assume _OSC PCIe control. Disabling ASPM [ 0.336386] ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *10 [ 0.336506] ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *11 [ 0.336622] ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled. [ 0.336740] ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled. [ 0.336856] ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *0, disabled. [ 0.336973] ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled. [ 0.337090] ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled. [ 0.337207] ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *10 [ 0.337323] ACPI: PCI Interrupt Link [LSMB] (IRQs *10) [ 0.337439] ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11 [ 0.337555] ACPI: PCI Interrupt Link [LUS2] (IRQs 22) *7 [ 0.337678] ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *11 [ 0.337794] ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *10 [ 0.337912] ACPI: PCI Interrupt Link [LGPU] (IRQs 16) *10 [ 0.338027] ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled. [ 0.338145] ACPI: PCI Interrupt Link [LSI0] (IRQs 23) *11 [ 0.338261] ACPI: PCI Interrupt Link [Z018] (IRQs 18) *5 [ 0.338390] ACPI: PCI Interrupt Link [Z019] (IRQs 22) *10 [ 0.338519] ACPI: PCI Interrupt Link [LPMU] (IRQs *11) [ 0.338673] vgaarb: device added: PCI:0000:00:12.0,decodes=io+mem,owns=io+mem,locks=none [ 0.338682] vgaarb: loaded [ 0.338948] SCSI subsystem initialized [ 0.340000] libata version 3.00 loaded. [ 0.340000] usbcore: registered new interface driver usbfs [ 0.340000] usbcore: registered new interface driver hub [ 0.340000] usbcore: registered new device driver usb [ 0.340000] wmi: Mapper loaded [ 0.340000] PCI: Using ACPI for IRQ routing [ 0.340000] PCI: pci_cache_line_size set to 64 bytes [ 0.340000] reserve RAM buffer: 000000000009e000 - 000000000009ffff [ 0.340000] reserve RAM buffer: 000000007bf50000 - 000000007bffffff [ 0.340000] NetLabel: Initializing [ 0.340000] NetLabel: domain hash size = 128 [ 0.340000] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.340000] NetLabel: unlabeled traffic allowed by default [ 0.340000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.340000] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 0.340000] hpet0: 3 comparators, 32-bit 25.000000 MHz counter [ 0.360093] Switching to clocksource hpet [ 0.370064] AppArmor: AppArmor Filesystem Enabled [ 0.370064] pnp: PnP ACPI init [ 0.370064] ACPI: bus type pnp registered [ 0.379410] pnp 00:00: [bus 00-ff] [ 0.379414] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.379417] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.379420] pnp 00:00: [io 0x0d00-0xffff window] [ 0.379422] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.379425] pnp 00:00: [mem 0x000c0000-0x000c3fff window] [ 0.379428] pnp 00:00: [mem 0x000c4000-0x000c7fff window] [ 0.379431] pnp 00:00: [mem 0x000c8000-0x000cbfff window] [ 0.379434] pnp 00:00: [mem 0x000cc000-0x000cffff window] [ 0.379437] pnp 00:00: [mem 0x000d0000-0x000d3fff window] [ 0.379440] pnp 00:00: [mem 0x000d4000-0x000d7fff window] [ 0.379443] pnp 00:00: [mem 0x000d8000-0x000dbfff window] [ 0.379446] pnp 00:00: [mem 0x000dc000-0x000dffff window] [ 0.379449] pnp 00:00: [mem 0x000e0000-0x000e3fff window] [ 0.379451] pnp 00:00: [mem 0x000e4000-0x000e7fff window] [ 0.379454] pnp 00:00: [mem 0x000e8000-0x000ebfff window] [ 0.379457] pnp 00:00: [mem 0x000ec000-0x000effff window] [ 0.379460] pnp 00:00: [mem 0x000f0000-0x000fffff window] [ 0.379463] pnp 00:00: [mem 0xfed40000-0xfed44fff window] [ 0.379470] pnp 00:00: [mem 0x80000000-0xfebfffff window] [ 0.379568] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.379638] Switched to NOHz mode on CPU #1 [ 0.379647] Switched to NOHz mode on CPU #0 [ 0.379809] pnp 00:01: [irq 0 disabled] [ 0.379825] pnp 00:01: [irq 8] [ 0.379827] pnp 00:01: [mem 0xfed00000-0xfed003ff] [ 0.379873] pnp 00:01: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.379895] pnp 00:02: [mem 0xe0000000-0xefffffff] [ 0.379988] system 00:02: [mem 0xe0000000-0xefffffff] has been reserved [ 0.379992] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.380234] pnp 00:03: [io 0x1000-0x107f] [ 0.380237] pnp 00:03: [io 0x1080-0x10ff] [ 0.380239] pnp 00:03: [io 0x1400-0x147f] [ 0.380242] pnp 00:03: [io 0x1480-0x14ff] [ 0.380244] pnp 00:03: [io 0x1800-0x187f] [ 0.380247] pnp 00:03: [io 0x1880-0x18ff] [ 0.380322] system 00:03: [io 0x1000-0x107f] has been reserved [ 0.380325] system 00:03: [io 0x1080-0x10ff] has been reserved [ 0.380328] system 00:03: [io 0x1400-0x147f] has been reserved [ 0.380332] system 00:03: [io 0x1480-0x14ff] has been reserved [ 0.380335] system 00:03: [io 0x1800-0x187f] has been reserved [ 0.380338] system 00:03: [io 0x1880-0x18ff] has been reserved [ 0.380342] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.380358] pnp 00:04: [io 0x0010-0x001f] [ 0.380360] pnp 00:04: [io 0x0022-0x003f] [ 0.380363] pnp 00:04: [io 0x0044-0x005f] [ 0.380365] pnp 00:04: [io 0x0063] [ 0.380368] pnp 00:04: [io 0x0065] [ 0.380370] pnp 00:04: [io 0x0067-0x006f] [ 0.380373] pnp 00:04: [io 0x0072-0x0073] [ 0.380375] pnp 00:04: [io 0x0074-0x007f] [ 0.380378] pnp 00:04: [io 0x0080] [ 0.380380] pnp 00:04: [io 0x0084] [ 0.380382] pnp 00:04: [io 0x0091-0x0093] [ 0.380385] pnp 00:04: [io 0x0097-0x009f] [ 0.380387] pnp 00:04: [io 0x00a2-0x00bf] [ 0.380390] pnp 00:04: [io 0x00e0-0x00ef] [ 0.380392] pnp 00:04: [io 0x0360-0x0361] [ 0.380395] pnp 00:04: [io 0x04d0-0x04d1] [ 0.380481] system 00:04: [io 0x0360-0x0361] has been reserved [ 0.380485] system 00:04: [io 0x04d0-0x04d1] has been reserved [ 0.380489] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.380508] pnp 00:05: [io 0x0000-0x0008] [ 0.380511] pnp 00:05: [io 0x000a-0x000f] [ 0.380514] pnp 00:05: [io 0x0081-0x0083] [ 0.380516] pnp 00:05: [io 0x0087] [ 0.380518] pnp 00:05: [io 0x0089-0x008b] [ 0.380521] pnp 00:05: [io 0x008f] [ 0.380523] pnp 00:05: [io 0x00c0-0x00d1] [ 0.380526] pnp 00:05: [io 0x00d4-0x00df] [ 0.380528] pnp 00:05: [dma 4] [ 0.380572] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.380584] pnp 00:06: [io 0x0061] [ 0.380627] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.380658] pnp 00:07: [io 0x0070-0x0071] [ 0.380705] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.380723] pnp 00:08: [io 0x00f0-0x00f1] [ 0.380733] pnp 00:08: [irq 13] [ 0.380775] pnp 00:08: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.380798] pnp 00:09: [io 0x0060] [ 0.380801] pnp 00:09: [io 0x0064] [ 0.380812] pnp 00:09: [irq 1] [ 0.380866] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.380886] pnp 00:0a: [irq 12] [ 0.380939] pnp 00:0a: Plug and Play ACPI device, IDs SYN013b SYN0100 SYN0002 PNP0f13 (active) [ 0.381369] pnp 00:0b: [mem 0xffc00000-0xffffffff] [ 0.381372] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.381374] pnp 00:0b: [mem 0xfee00000-0xfeefffff] [ 0.381377] pnp 00:0b: [mem 0xfed00000-0xfed00fff] [ 0.381380] pnp 00:0b: [mem 0x00000000-0xffffffffffffffff disabled] [ 0.381383] pnp 00:0b: [mem 0xfef00000-0xfef00fff] [ 0.381478] system 00:0b: [mem 0xffc00000-0xffffffff] could not be reserved [ 0.381482] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.381485] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved [ 0.381489] system 00:0b: [mem 0xfed00000-0xfed00fff] has been reserved [ 0.381493] system 00:0b: [mem 0xfef00000-0xfef00fff] has been reserved [ 0.381496] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.381621] pnp: PnP ACPI: found 12 devices [ 0.381623] ACPI: ACPI bus type pnp unregistered [ 0.388106] pci 0000:00:12.0: BAR 6: assigned [mem 0x80000000-0x8001ffff pref] [ 0.388112] pci 0000:00:08.0: PCI bridge to [bus 02-02] [ 0.388115] pci 0000:00:08.0: bridge window [io disabled] [ 0.388119] pci 0000:00:08.0: bridge window [mem 0xf6100000-0xf61fffff] [ 0.388122] pci 0000:00:08.0: bridge window [mem pref disabled] [ 0.388127] pci 0000:00:0c.0: PCI bridge to [bus 04-05] [ 0.388130] pci 0000:00:0c.0: bridge window [io 0x4000-0x4fff] [ 0.388134] pci 0000:00:0c.0: bridge window [mem 0xf2000000-0xf3ffffff] [ 0.388138] pci 0000:00:0c.0: bridge window [mem 0xf0000000-0xf1ffffff 64bit pref] [ 0.388142] pci 0000:00:0d.0: PCI bridge to [bus 03-03] [ 0.388144] pci 0000:00:0d.0: bridge window [io disabled] [ 0.388148] pci 0000:00:0d.0: bridge window [mem 0xf6000000-0xf60fffff] [ 0.388151] pci 0000:00:0d.0: bridge window [mem pref disabled] [ 0.388161] pci 0000:00:08.0: setting latency timer to 64 [ 0.388167] pci 0000:00:0c.0: setting latency timer to 64 [ 0.388172] pci 0000:00:0d.0: setting latency timer to 64 [ 0.388176] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.388179] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.388182] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.388185] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff] [ 0.388188] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff] [ 0.388191] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff] [ 0.388194] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff] [ 0.388197] pci_bus 0000:00: resource 11 [mem 0x000d4000-0x000d7fff] [ 0.388199] pci_bus 0000:00: resource 12 [mem 0x000d8000-0x000dbfff] [ 0.388202] pci_bus 0000:00: resource 13 [mem 0x000dc000-0x000dffff] [ 0.388205] pci_bus 0000:00: resource 14 [mem 0x000e0000-0x000e3fff] [ 0.388208] pci_bus 0000:00: resource 15 [mem 0x000e4000-0x000e7fff] [ 0.388211] pci_bus 0000:00: resource 16 [mem 0x000e8000-0x000ebfff] [ 0.388214] pci_bus 0000:00: resource 17 [mem 0x000ec000-0x000effff] [ 0.388217] pci_bus 0000:00: resource 18 [mem 0x000f0000-0x000fffff] [ 0.388220] pci_bus 0000:00: resource 19 [mem 0xfed40000-0xfed44fff] [ 0.388223] pci_bus 0000:00: resource 20 [mem 0x80000000-0xfebfffff] [ 0.388226] pci_bus 0000:02: resource 1 [mem 0xf6100000-0xf61fffff] [ 0.388229] pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7] [ 0.388232] pci_bus 0000:02: resource 5 [io 0x0d00-0xffff] [ 0.388235] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff] [ 0.388238] pci_bus 0000:02: resource 7 [mem 0x000c0000-0x000c3fff] [ 0.388240] pci_bus 0000:02: resource 8 [mem 0x000c4000-0x000c7fff] [ 0.388243] pci_bus 0000:02: resource 9 [mem 0x000c8000-0x000cbfff] [ 0.388246] pci_bus 0000:02: resource 10 [mem 0x000cc000-0x000cffff] [ 0.388249] pci_bus 0000:02: resource 11 [mem 0x000d4000-0x000d7fff] [ 0.388252] pci_bus 0000:02: resource 12 [mem 0x000d8000-0x000dbfff] [ 0.388255] pci_bus 0000:02: resource 13 [mem 0x000dc000-0x000dffff] [ 0.388258] pci_bus 0000:02: resource 14 [mem 0x000e0000-0x000e3fff] [ 0.388261] pci_bus 0000:02: resource 15 [mem 0x000e4000-0x000e7fff] [ 0.388264] pci_bus 0000:02: resource 16 [mem 0x000e8000-0x000ebfff] [ 0.388267] pci_bus 0000:02: resource 17 [mem 0x000ec000-0x000effff] [ 0.388270] pci_bus 0000:02: resource 18 [mem 0x000f0000-0x000fffff] [ 0.388273] pci_bus 0000:02: resource 19 [mem 0xfed40000-0xfed44fff] [ 0.388276] pci_bus 0000:02: resource 20 [mem 0x80000000-0xfebfffff] [ 0.388279] pci_bus 0000:04: resource 0 [io 0x4000-0x4fff] [ 0.388282] pci_bus 0000:04: resource 1 [mem 0xf2000000-0xf3ffffff] [ 0.388285] pci_bus 0000:04: resource 2 [mem 0xf0000000-0xf1ffffff 64bit pref] [ 0.388288] pci_bus 0000:03: resource 1 [mem 0xf6000000-0xf60fffff] [ 0.388339] NET: Registered protocol family 2 [ 0.388481] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.389562] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 0.391888] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.392411] TCP: Hash tables configured (established 262144 bind 65536) [ 0.392414] TCP reno registered [ 0.392428] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.392454] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.392584] NET: Registered protocol family 1 [ 0.392756] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.392810] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.392868] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.392933] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.393002] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.393075] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 0.393083] pci 0000:00:12.0: Boot video device [ 0.393108] PCI: CLS 64 bytes, default 64 [ 0.520309] Simple Boot Flag at 0x36 set to 0x1 [ 0.520652] audit: initializing netlink socket (disabled) [ 0.520664] type=2000 audit(1307381453.520:1): initialized [ 0.546638] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.549053] VFS: Disk quotas dquot_6.5.2 [ 0.549131] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.549900] fuse init (API version 7.16) [ 0.550057] msgmni has been set to 3856 [ 0.550364] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.550400] io scheduler noop registered [ 0.550403] io scheduler deadline registered [ 0.550452] io scheduler cfq registered (default) [ 0.560069] pcieport 0000:00:0c.0: setting latency timer to 64 [ 0.560105] pcieport 0000:00:0c.0: irq 40 for MSI/MSI-X [ 0.560226] pcieport 0000:00:0d.0: setting latency timer to 64 [ 0.560250] pcieport 0000:00:0d.0: irq 41 for MSI/MSI-X [ 0.560350] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.560382] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.560875] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.561149] ACPI: AC Adapter [ACAD] (on-line) [ 0.561243] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 0.561250] ACPI: Sleep Button [SLPB] [ 0.561298] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 [ 0.561533] ACPI: Lid Switch [LID] [ 0.561593] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2 [ 0.561598] ACPI: Power Button [PWRB] [ 0.561647] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 0.561651] ACPI: Power Button [PWRF] [ 0.561901] ACPI: acpi_idle registered with cpuidle [ 0.562189] ACPI: processor limited to max C-state 1 [ 0.564498] [Firmware Bug]: Invalid critical threshold (0) [ 0.564902] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.564905] ACPI: Thermal Zone [THRM] (44 C) [ 0.564926] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.564987] ERST: Table is not found! [ 0.565080] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.635885] Freeing initrd memory: 13700k freed [ 0.830297] ACPI: Battery Slot [BAT0] (battery present) [ 1.120485] Linux agpgart interface v0.103 [ 1.121764] brd: module loaded [ 1.122343] loop: module loaded [ 1.122736] pata_acpi 0000:00:06.0: setting latency timer to 64 [ 1.123056] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23 [ 1.123076] pata_acpi 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23 [ 1.123094] pata_acpi 0000:00:09.0: setting latency timer to 64 [ 1.123104] pata_acpi 0000:00:09.0: PCI INT A disabled [ 1.123663] Fixed MDIO Bus: probed [ 1.123696] PPP generic driver version 2.4.2 [ 1.123759] tun: Universal TUN/TAP device driver, 1.6 [ 1.123761] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 1.123869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.124105] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 [ 1.124117] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 22 (level, low) -> IRQ 22 [ 1.124135] ehci_hcd 0000:00:02.1: setting latency timer to 64 [ 1.124139] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 1.124225] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 1.150052] ehci_hcd 0000:00:02.1: debug port 1 [ 1.150060] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported [ 1.150085] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf6489000 [ 1.170029] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00 [ 1.170163] hub 1-0:1.0: USB hub found [ 1.170168] hub 1-0:1.0: 7 ports detected [ 1.170517] ACPI: PCI Interrupt Link [Z019] enabled at IRQ 22 [ 1.170522] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z019] -> GSI 22 (level, low) -> IRQ 22 [ 1.170537] ehci_hcd 0000:00:04.1: setting latency timer to 64 [ 1.170540] ehci_hcd 0000:00:04.1: EHCI Host Controller [ 1.170593] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2 [ 1.170642] ehci_hcd 0000:00:04.1: debug port 1 [ 1.170649] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported [ 1.170659] ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400 [ 1.190029] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00 [ 1.190144] hub 2-0:1.0: USB hub found [ 1.190148] hub 2-0:1.0: 2 ports detected [ 1.190237] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.190488] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18 [ 1.190504] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 18 (level, low) -> IRQ 18 [ 1.190518] ohci_hcd 0000:00:02.0: setting latency timer to 64 [ 1.190522] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 1.190569] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3 [ 1.190627] ohci_hcd 0000:00:02.0: irq 18, io mem 0xf6486000 [ 1.252144] hub 3-0:1.0: USB hub found [ 1.252151] hub 3-0:1.0: 7 ports detected [ 1.252476] ACPI: PCI Interrupt Link [Z018] enabled at IRQ 18 [ 1.252481] ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z018] -> GSI 18 (level, low) -> IRQ 18 [ 1.252494] ohci_hcd 0000:00:04.0: setting latency timer to 64 [ 1.252498] ohci_hcd 0000:00:04.0: OHCI Host Controller [ 1.252546] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4 [ 1.252588] ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000 [ 1.312143] hub 4-0:1.0: USB hub found [ 1.312149] hub 4-0:1.0: 2 ports detected [ 1.312237] uhci_hcd: USB Universal Host Controller Interface driver [ 1.340050] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 1.361866] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.361873] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.362025] mousedev: PS/2 mouse device common for all mice [ 1.363810] rtc_cmos 00:07: RTC can wake from S4 [ 1.382649] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 1.390152] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 1.390192] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs [ 1.390314] device-mapper: uevent: version 1.0.3 [ 1.390402] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@xxxxxxxxxx [ 1.390512] device-mapper: multipath: version 1.3.0 loaded [ 1.390515] device-mapper: multipath round-robin: version 1.0.0 loaded [ 1.390597] cpuidle: using governor ladder [ 1.390599] cpuidle: using governor menu [ 1.390601] EFI Variables Facility v0.08 2004-May-17 [ 1.390915] TCP cubic registered [ 1.391065] NET: Registered protocol family 10 [ 1.395820] NET: Registered protocol family 17 [ 1.395844] Registering the dns_resolver key type [ 1.395879] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-60 (2 cpu cores) (version 2.20.00) [ 1.395935] powernow-k8: fid 0xc (2000 MHz), vid 0x11 [ 1.395937] powernow-k8: fid 0xa (1800 MHz), vid 0x12 [ 1.395940] powernow-k8: fid 0x8 (1600 MHz), vid 0x13 [ 1.395942] powernow-k8: fid 0x0 (800 MHz), vid 0x1e [ 1.396131] PM: Hibernation image not present or could not be loaded. [ 1.396151] registered taskstats version 1 [ 1.396594] Magic number: 15:729:541 [ 1.396706] rtc_cmos 00:07: setting system clock to 2011-06-06 17:30:54 UTC (1307381454) [ 1.396710] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.396711] EDD information not available. [ 1.398997] Freeing unused kernel memory: 988k freed [ 1.399491] Write protecting the kernel read-only data: 10240k [ 1.399895] Freeing unused kernel memory: 56k freed [ 1.405891] Freeing unused kernel memory: 1412k freed [ 1.430267] udevd[95]: starting version 170 [ 1.508492] pata_amd 0000:00:06.0: version 0.4.1 [ 1.508546] pata_amd 0000:00:06.0: setting latency timer to 64 [ 1.508934] scsi0 : pata_amd [ 1.510451] scsi1 : pata_amd [ 1.510812] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14 [ 1.510816] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15 [ 1.512519] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. [ 1.512772] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20 [ 1.512792] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20 [ 1.512797] forcedeth 0000:00:0a.0: setting latency timer to 64 [ 1.577806] sdhci: Secure Digital Host Controller Interface driver [ 1.577811] sdhci: Copyright(c) Pierre Ossman [ 1.630092] usb 2-2: new high speed USB device number 3 using ehci_hcd [ 1.710301] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L632N, 0503, max MWDMA2 [ 1.710310] ata1: nv_mode_filter: 0x39f&0x739f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12) [ 1.750239] ata1.00: configured for MWDMA2 [ 1.754668] scsi 0:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L632N 0503 PQ: 0 ANSI: 5 [ 1.761072] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.761075] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.761233] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 1.761326] sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 1.761474] ata2: port disabled. ignoring. [ 1.764608] sdhci-pci 0000:02:05.1: SDHCI controller found [1180:0822] (rev 22) [ 1.764863] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7 [ 1.764882] sdhci-pci 0000:02:05.1: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7 [ 1.765919] sdhci-pci 0000:02:05.1: Will use DMA mode even though HW doesn't fully claim to support it. [ 1.765943] mmc0: no vmmc regulator found [ 1.766990] Registered led device: mmc0:: [ 1.775706] mmc0: SDHCI controller on PCI [0000:02:05.1] using DMA [ 1.776218] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5 [ 1.776236] firewire_ohci 0000:02:05.0: PCI INT A -> Link[LNK1] -> GSI 5 (level, low) -> IRQ 5 [ 1.831431] firewire_ohci: Added fw-ohci device 0000:02:05.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x1 [ 2.040535] forcedeth 0000:00:0a.0: eth0: Features changed: 0x00004820 -> 0x00004020 [ 2.041001] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1e:68:09:25:f6 [ 2.041006] forcedeth 0000:00:0a.0: highdma pwrctl mgmt lnktim msi desc-v3 [ 2.041459] ahci 0000:00:09.0: version 3.0 [ 2.041475] ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23 [ 2.041503] ahci 0000:00:09.0: controller can do NCQ, turning on CAP_NCQ [ 2.041506] ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP [ 2.041561] ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 2.041565] ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio slum part [ 2.041570] ahci 0000:00:09.0: setting latency timer to 64 [ 2.042346] scsi2 : ahci [ 2.042433] scsi3 : ahci [ 2.042508] scsi4 : ahci [ 2.042584] scsi5 : ahci [ 2.042735] ata3: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484100 irq 23 [ 2.042738] ata4: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484180 irq 23 [ 2.042742] ata5: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484200 irq 23 [ 2.042745] ata6: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484280 irq 23 [ 2.180030] usb 4-1: new full speed USB device number 2 using ohci_hcd [ 2.330132] firewire_core: created device fw0: GUID 00241b00964cac00, S400 [ 2.390040] ata6: SATA link down (SStatus 0 SControl 300) [ 2.390060] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.390077] ata5: SATA link down (SStatus 0 SControl 300) [ 2.390087] ata4: SATA link down (SStatus 0 SControl 300) [ 2.390819] ata3.00: ATA-8: Hitachi HTS542525K9SA00, BBFOC32P, max UDMA/100 [ 2.390822] ata3.00: 488397168 sectors, multi 16: LBA48 [ 2.391752] ata3.00: configured for UDMA/100 [ 2.391911] scsi 2:0:0:0: Direct-Access ATA Hitachi HTS54252 BBFO PQ: 0 ANSI: 5 [ 2.392093] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 2.392118] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 2.392159] sd 2:0:0:0: [sda] Write Protect is off [ 2.392163] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.392193] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.392436] sda: detected capacity change from 0 to 250059350016 [ 2.734244] sda: sda1 sda2 < sda5 sda6 > [ 2.734616] sd 2:0:0:0: [sda] Attached SCSI disk [ 3.141399] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 7.858762] udevd[378]: starting version 170 [ 7.925844] lp: driver loaded but no devices found [ 8.018429] Adding 195173372k swap on /dev/sda6. Priority:-1 extents:1 across:195173372k [ 8.151526] acpi device:24: registered as cooling_device2 [ 8.151627] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 8.151691] ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no) [ 8.165370] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro [ 8.230150] i2c i2c-0: nForce2 SMBus adapter at 0x3040 [ 8.230185] i2c i2c-1: nForce2 SMBus adapter at 0x3000 [ 8.312077] MCE: In-kernel MCE decoding enabled. [ 8.318073] EDAC MC: Ver: 2.1.0 May 28 2011 [ 8.349356] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 8.420417] EXT3-fs: barriers not enabled [ 8.430336] kjournald starting. Commit interval 5 seconds [ 8.430582] EXT3-fs (sda1): using internal journal [ 8.430588] EXT3-fs (sda1): mounted filesystem with ordered data mode [ 8.510840] AMD64 EDAC driver v3.4.0 [ 8.539723] EDAC amd64: DRAM ECC disabled. [ 8.540787] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. [ 8.540789] Either enable ECC checking or force module loading by setting 'ecc_enable_override'. [ 8.540790] (Note that use of the override may cause unknown side effects.) [ 8.684937] type=1400 audit(1307381461.782:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=641 comm="apparmor_parser" [ 8.685348] type=1400 audit(1307381461.782:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=641 comm="apparmor_parser" [ 8.685615] type=1400 audit(1307381461.782:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=641 comm="apparmor_parser" [ 8.783316] type=1400 audit(1307381461.882:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=711 comm="apparmor_parser" [ 8.790712] type=1400 audit(1307381461.892:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=711 comm="apparmor_parser" [ 8.790990] type=1400 audit(1307381461.892:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=711 comm="apparmor_parser" [ 8.794723] type=1400 audit(1307381461.892:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=712 comm="apparmor_parser" [ 8.892341] [drm] Initialized drm 1.1.0 20060810 [ 9.091003] forcedeth 0000:00:0a.0: irq 42 for MSI/MSI-X [ 9.127100] Linux video capture interface: v2.00 [ 9.145776] cfg80211: Calling CRDA to update world regulatory domain [ 9.230483] uvcvideo: Found UVC 1.00 device HP Webcam (0408:030c) [ 9.235482] input: HP Webcam as /devices/pci0000:00/0000:00:04.1/usb2/2-2/2-2:1.0/input/input6 [ 9.235631] usbcore: registered new interface driver uvcvideo [ 9.235633] USB Video Class driver (v1.0.0) [ 9.236482] r852 0000:02:05.3: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7 [ 9.240673] r852: Non dma capable device detected, dma disabled [ 9.240693] r852: driver loaded successfully [ 9.273586] Bluetooth: Core ver 2.16 [ 9.280185] NET: Registered protocol family 31 [ 9.280189] Bluetooth: HCI device and connection manager initialized [ 9.280193] Bluetooth: HCI socket layer initialized [ 9.280195] Bluetooth: L2CAP socket layer initialized [ 9.287154] Bluetooth: SCO socket layer initialized [ 9.296925] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 9.302833] usbcore: registered new interface driver btusb [ 9.319887] input: HP WMI hotkeys as /devices/virtual/input/input7 [ 9.347108] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000/0x0 [ 9.363882] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16 [ 9.363913] nouveau 0000:00:12.0: PCI INT A -> Link[LGPU] -> GSI 16 (level, low) -> IRQ 16 [ 9.363919] nouveau 0000:00:12.0: setting latency timer to 64 [ 9.365510] [drm] nouveau 0000:00:12.0: Detected an NV40 generation card (0x067000a1) [ 9.367509] [drm] nouveau 0000:00:12.0: Attempting to load BIOS image from PRAMIN [ 9.410558] [drm] nouveau 0000:00:12.0: ... appears to be valid [ 9.410563] [drm] nouveau 0000:00:12.0: BIT BIOS found [ 9.410567] [drm] nouveau 0000:00:12.0: Bios version 05.67.32.16 [ 9.410570] [drm] nouveau 0000:00:12.0: TMDS table version 1.1 [ 9.410572] [drm] nouveau 0000:00:12.0: TMDS table script pointers not stubbed [ 9.410575] [drm] nouveau 0000:00:12.0: BIT table 'd' not found [ 9.410578] [drm] nouveau 0000:00:12.0: Found Display Configuration Block version 3.0 [ 9.410582] [drm] nouveau 0000:00:12.0: Raw DCB entry 0: 03015323 00000004 [ 9.410585] [drm] nouveau 0000:00:12.0: Raw DCB entry 1: 01000310 00000023 [ 9.410588] [drm] nouveau 0000:00:12.0: Raw DCB entry 2: 020223f1 0040c080 [ 9.410592] [drm] nouveau 0000:00:12.0: DCB connector table: VHER 0x30 5 10 2 [ 9.410596] [drm] nouveau 0000:00:12.0: 0: 0x00000000: type 0x00 idx 0 tag 0xff [ 9.410599] [drm] nouveau 0000:00:12.0: 1: 0x00001161: type 0x61 idx 1 tag 0x07 [ 9.410602] [drm] nouveau 0000:00:12.0: 2: 0x00000210: type 0x10 idx 2 tag 0xff [ 9.410605] [drm] nouveau 0000:00:12.0: 3: 0x00000211: type 0x11 idx 3 tag 0xff [ 9.410608] [drm] nouveau 0000:00:12.0: 4: 0x00000213: type 0x13 idx 4 tag 0xff [ 9.410611] [drm] nouveau 0000:00:12.0: 5: 0x00000340: type 0x40 idx 5 tag 0xff [ 9.410618] [drm] nouveau 0000:00:12.0: Parsing VBIOS init table 0 at offset 0xE333 [ 9.410641] [drm] nouveau 0000:00:12.0: ======= misaligned reg 0x001020FB ======= [ 9.410647] [drm] nouveau 0000:00:12.0: ======= misaligned reg 0x001020FB ======= [ 9.410677] [drm] nouveau 0000:00:12.0: Parsing VBIOS init table 1 at offset 0xE484 [ 9.410680] [drm] nouveau 0000:00:12.0: Parsing VBIOS init table 2 at offset 0xE485 [ 9.410698] [drm] nouveau 0000:00:12.0: Parsing VBIOS init table 3 at offset 0xE607 [ 9.410706] [drm] nouveau 0000:00:12.0: Parsing VBIOS init table 4 at offset 0xE687 [ 9.410936] ACPI: PCI Interrupt Link [LK4E] enabled at IRQ 19 [ 9.410959] ath5k 0000:03:00.0: PCI INT A -> Link[LK4E] -> GSI 19 (level, low) -> IRQ 19 [ 9.410968] ath5k 0000:03:00.0: setting latency timer to 64 [ 9.411022] ath5k 0000:03:00.0: registered as 'phy0' [ 9.424285] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 9.883660] [drm] nouveau 0000:00:12.0: 3 available performance level(s) [ 9.883665] [drm] nouveau 0000:00:12.0: 0: memory 0MHz core 100MHz voltage 1100mV fanspeed 100% [ 9.883670] [drm] nouveau 0000:00:12.0: 1: memory 0MHz core 250MHz voltage 1200mV fanspeed 100% [ 9.883674] [drm] nouveau 0000:00:12.0: 2: memory 0MHz core 425MHz voltage 1200mV fanspeed 100% [ 9.883683] [drm] nouveau 0000:00:12.0: c: memory 0MHz [ 9.923792] [TTM] Zone kernel: Available graphics memory: 995256 kiB. [ 9.923794] [TTM] Initializing pool allocator. [ 9.923811] [drm] nouveau 0000:00:12.0: Detected 64MiB VRAM [ 9.924465] [drm] nouveau 0000:00:12.0: 64 MiB GART (aperture) [ 9.924527] [drm] nouveau 0000:00:12.0: Saving VGA fonts [ 9.965721] ath: EEPROM regdomain: 0x64 [ 9.965723] ath: EEPROM indicates we should expect a direct regpair map [ 9.965728] ath: Country alpha2 being used: 00 [ 9.965730] ath: Regpair used: 0x64 [ 9.965733] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: [ 9.965737] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965739] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: [ 9.965742] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965745] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: [ 9.965748] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965750] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: [ 9.965753] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965756] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: [ 9.965759] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965761] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: [ 9.965764] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965767] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: [ 9.965770] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965772] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: [ 9.965776] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965778] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: [ 9.965781] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965784] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: [ 9.965787] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965789] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: [ 9.965792] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm) [ 9.965795] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 9.965797] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 9.965800] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel [ 9.965875] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 9.966380] [drm] nouveau 0000:00:12.0: ACPI backlight interface available, not registering our own [ 9.967718] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 9.967721] [drm] No driver support for vblank timestamp query. [ 9.968017] [drm] nouveau 0000:00:12.0: Setting dpms mode 3 on lvds encoder (output 0) [ 9.968021] [drm] nouveau 0000:00:12.0: Calling LVDS script 6: [ 9.968025] [drm] nouveau 0000:00:12.0: 0xD680: Parsing digital output script table [ 9.968033] [drm] nouveau 0000:00:12.0: Setting dpms mode 3 on vga encoder (output 1) [ 9.968036] [drm] nouveau 0000:00:12.0: Setting dpms mode 3 on TV encoder (output 2) [ 10.098564] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 10.098765] ath5k 0000:03:00.0: wlan0: Features changed: 0x00004800 -> 0x00004000 [ 10.099297] Registered led device: ath5k-phy0::rx [ 10.099319] Registered led device: ath5k-phy0::tx [ 10.099327] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70) [ 10.210034] [drm] nouveau 0000:00:12.0: Load detected on output B [ 10.210590] [drm] nouveau 0000:00:12.0: allocated 1280x800 fb: 0x49000, bo ffff88006ba21400 [ 10.210779] fbcon: nouveaufb (fb0) is primary device [ 10.214154] Console: switching to colour frame buffer device 90x36 [ 10.214172] fb0: nouveaufb frame buffer device [ 10.214174] drm: registered panic notifier [ 10.214183] [drm] Initialized nouveau 0.0.16 20090420 for 0000:00:12.0 on minor 0 [ 10.214532] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21 [ 10.214559] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21 [ 10.214818] hda_intel: Disable MSI for Nvidia chipset [ 10.214876] HDA Intel 0000:00:07.0: setting latency timer to 64 [ 11.360152] input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:07.0/sound/card0/input9 [ 19.580022] eth0: no IPv6 routers present 00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 800MHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 3080 [size=64] Region 4: I/O ports at 3040 [size=64] Region 5: I/O ports at 3000 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 11 Region 0: Memory at f6200000 (32-bit, non-prefetchable) [size=512K] 00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 18 Region 0: Memory at f6486000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 22 Region 0: Memory at f6489000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 18 Region 0: Memory at f6487000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 22 Region 0: Memory at f6489400 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at 30c0 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f6480000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=64 Memory behind bridge: f6100000-f61fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: [b8] Subsystem: nVidia Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 30f0 [size=8] Region 1: I/O ports at 30e4 [size=4] Region 2: I/O ports at 30e8 [size=8] Region 3: I/O ports at 30e0 [size=4] Region 4: I/O ports at 30d0 [size=16] Region 5: Memory at f6484000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [8c] SATA HBA v1.0 InCfgSpace Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci Kernel modules: ahci 00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 42 Region 0: Memory at f6488000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 30f8 [size=8] Region 2: Memory at f6489c00 (32-bit, non-prefetchable) [size=256] Region 3: Memory at f6489800 (32-bit, non-prefetchable) [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit+ Address: 00000000fee0100c Data: 4169 Masking: 000000fe Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: forcedeth Kernel modules: forcedeth 00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: f2000000-f3ffffff Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device 0000 Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4129 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+ LinkChg+ Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: f6000000-f60fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device 0000 Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4141 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #3, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+ LinkChg+ Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: nVidia Corporation C67 [GeForce 7150M / nForce 630M] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8 IsocEn- LSEn+ ExtCTL- 64b+ Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 1.02 Link Frequency: 800MHz Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- ExtRS- UCnfE- 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: amd64_edac_mod 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 02:05.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 5 Region 0: Memory at f6100000 (32-bit, non-prefetchable) [size=2K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+ Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 02:05.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 7 Region 0: Memory at f6100800 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 02:05.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at f6101000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- 02:05.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12) Subsystem: Hewlett-Packard Company Device 30cf Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 7 Region 0: Memory at f6101400 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: r852 Kernel modules: r852 03:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Hewlett-Packard Company AR5BXB63 (Foxconn) 802.11bg Mini PCIe NIC Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at f6000000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [90] MSI-X: Enable- Count=1 Masked- Vector table: BAR=0 offset=00000000 PBA: BAR=0 offset=00000000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: ath5k Kernel modules: ath5k After inserting a firewire card: 00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: f2000000-f3ffffff Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Device 0000 Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4129 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+ LinkChg+ Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport Kernel modules: shpchp 227c227 < LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- --- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- 232,233c232,233 < SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- < Changed: MRL- PresDet+ LinkState+ --- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- > Changed: MRL- PresDet- LinkState- last line of dmesg still: [ 19.580022] eth0: no IPv6 routers present pull card juser@pc8:~$ sudo modprobe acpiphp juser@pc8:~$ sudo dmesg -c [ 1189.609674] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 1189.610754] acpiphp: Slot [1] registered insert card: juser@pc8:~$ sudo dmesg -c [ 1722.265317] pci 0000:04:00.0: [11c1:5901] type 0 class 0x000c00 [ 1722.265354] pci 0000:04:00.0: reg 10: [mem 0x00000000-0x00000fff 64bit] [ 1722.265440] pci 0000:04:00.0: supports D1 D2 [ 1722.265447] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1722.265457] pci 0000:04:00.0: PME# disabled [ 1722.265838] pci 0000:04:00.0: BAR 0: assigned [mem 0xf2000000-0xf2000fff 64bit] [ 1722.265855] pci 0000:04:00.0: BAR 0: set to [mem 0xf2000000-0xf2000fff 64bit] (PCI address [0xf2000000-0xf2000fff]) [ 1722.265887] pci 0000:04:00.0: no hotplug settings from platform [ 1722.266623] firewire_ohci 0000:04:00.0: enabling device (0000 -> 0002) [ 1722.267081] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 16 [ 1722.267096] firewire_ohci 0000:04:00.0: PCI INT A -> Link[LK1E] -> GSI 16 (level, low) -> IRQ 16 [ 1722.267111] firewire_ohci 0000:04:00.0: setting latency timer to 64 [ 1722.320139] firewire_ohci: Added fw-ohci device 0000:04:00.0, OHCI v1.10, 8 IR + 8 IT contexts, quirks 0x10 [ 1722.820339] firewire_core: created device fw1: GUID 0108000000006351, S800 222c222 < DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- --- > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- 227c227 < LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- --- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- 232,233c232,233 < SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- < Changed: MRL- PresDet- LinkState- --- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ LinkState+ 440a441,489 > > 04:00.0 FireWire (IEEE 1394): Agere Systems FW643 PCI Express1394b Controller (PHY/Link) (rev 06) (prog-if 10 [OHCI]) > Subsystem: Device 5901:1101 > Physical Slot: 1 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at f2000000 (64-bit, non-prefetchable) [size=4K] > Capabilities: [44] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ > Capabilities: [4c] MSI: Enable- Count=1/1 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [60] Express (v1) Endpoint, MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- > Capabilities: [140 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 > Status: NegoPending- InProgress- > Capabilities: [170 v1] Device Serial Number 01-08-00-00-00-00-63-51 > Kernel driver in use: firewire_ohci > Kernel modules: firewire-ohci -- Carl K -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
