From: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx>
ipq6018 has 1 pcie gen3 port. This patch adds the support for the same.
The GICv2m reg property value is a guess based on similar SoCs
description in downstream Codeaurora kernel. It appears to work.
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx>
[baruch: adjust #address-cells/#size-cells; drop unsupported property;
use v2m msi interrupts parent; increase parf registers size]
Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 109 ++++++++++++++++++++++++++
1 file changed, 109 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 9fa5b028e4f3..a5b03b0d564b 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -375,6 +375,8 @@ qpic_nand: nand@79b0000 {
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
+ #address-cells = <1>;
+ #size-cells = <1>;
interrupt-controller;
#interrupt-cells = <0x3>;
reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/
@@ -382,6 +384,113 @@ intc: interrupt-controller@b000000 {
<0x0 0x0b001000 0x0 0x1000>, /*GICH*/
<0x0 0x0b004000 0x0 0x1000>; /*GICV*/
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ ranges = <0x0 0x0 0xb00a000 0xffd>;
+
+ v2m0: v2m@0 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x0 0xffd>;
+ };
+ };
+
+ pcie_phy: phy@84000 {
+ compatible = "qcom,ipq6018-qmp-pcie-phy";
+ reg = <0x0 0x84000 0x0 0x1bc>; /* Serdes PLL */
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+
+ pcie_phy0: lane@84200 {
+ reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */
+ <0x0 0x84400 0x0 0x200>, /* Serdes Rx */
+ <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie0_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie0: pci@20000000 {
+ compatible = "qcom,pcie-ipq6018";
+ reg = <0x0 0x20000000 0x0 0xf1d>,
+ <0x0 0x20000f20 0x0 0xa8>,
+ <0x0 0x20001000 0x0 0x1000>,
+ <0x0 0x80000 0x0 0x4000>,
+ <0x0 0x20100000 0x0 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ phys = <&pcie_phy0>;
+ phy-names = "pciephy";
+
+ ranges = <0x81000000 0 0x20200000 0 0x20200000
+ 0 0x10000>, /* downstream I/O */
+ <0x82000000 0 0x20220000 0 0x20220000
+ 0 0xfde0000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ msi-parent = <&v2m0>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+ <&gcc PCIE0_RCHNG_CLK>;
+ clock-names = "iface",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_SLEEP_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
+ reset-names = "pipe",
+ "sleep",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "axi_m_sticky",
+ "axi_s_sticky";
+
+ status = "disabled";
};
watchdog@b017000 {
--
2.30.2
