Pali Rohár <pali@xxxxxxxxxx> writes: > On Friday 26 March 2021 16:25:27 Toke Høiland-Jørgensen wrote: >> Pali Rohár <pali@xxxxxxxxxx> writes: >> >> > On Friday 19 March 2021 00:16:29 Pali Rohár wrote: >> >> On Thursday 18 March 2021 23:43:58 Toke Høiland-Jørgensen wrote: >> >> > Pali Rohár <pali@xxxxxxxxxx> writes: >> >> > >> >> > > On Monday 15 March 2021 20:58:06 Pali Rohár wrote: >> >> > >> On Monday 02 November 2020 16:54:35 Toke Høiland-Jørgensen wrote: >> >> > >> > Pali Rohár <pali@xxxxxxxxxx> writes: >> >> > >> > >> >> > >> > > On Saturday 31 October 2020 13:49:49 Toke Høiland-Jørgensen wrote: >> >> > >> > >> "™֟☻̭҇ Ѽ ҉ ®" <vtolkm@xxxxxxxxxxxxxx> writes: >> >> > >> > >> >> >> > >> > >> > On 30/10/2020 15:23, Pali Rohár wrote: >> >> > >> > >> >> On Friday 30 October 2020 14:02:22 Toke Høiland-Jørgensen wrote: >> >> > >> > >> >>> Pali Rohár <pali@xxxxxxxxxx> writes: >> >> > >> > >> >>>> My experience with that WLE900VX card, aardvark driver and aspm code: >> >> > >> > >> >>>> >> >> > >> > >> >>>> Link training in GEN2 mode for this card succeed only once after reset. >> >> > >> > >> >>>> Repeated link retraining fails and it fails even when aardvark is >> >> > >> > >> >>>> reconfigured to GEN1 mode. Reset via PERST# signal is required to have >> >> > >> > >> >>>> working link training. >> >> > >> > >> >>>> >> >> > >> > >> >>>> What I did in aardvark driver: Set mode to GEN2, do link training. If >> >> > >> > >> >>>> success read "negotiated link speed" from "Link Control Status Register" >> >> > >> > >> >>>> (for WLE900VX it is 0x1 - GEN1) and set it into aardvark. And then >> >> > >> > >> >>>> retrain link again (for WLE900VX now it would be at GEN1). After that >> >> > >> > >> >>>> card is stable and all future retraining (e.g. from aspm.c) also passes. >> >> > >> > >> >>>> >> >> > >> > >> >>>> If I do not change aardvark mode from GEN2 to GEN1 the second link >> >> > >> > >> >>>> training fails. And if I change mode to GEN1 after this failed link >> >> > >> > >> >>>> training then nothing happen, link training do not success. >> >> > >> > >> >>>> >> >> > >> > >> >>>> So just speculation now... In current setup initialization of card does >> >> > >> > >> >>>> one link training at GEN2. Then aspm.c is called which is doing second >> >> > >> > >> >>>> link retraining at GEN2. And if it fails then below patch issue third >> >> > >> > >> >>>> link retraining at GEN1. If A38x/pci-mvebu has same problem as aardvark >> >> > >> > >> >>>> then second link retraining must be at GEN1 (not GEN2) to workaround >> >> > >> > >> >>>> this issue. >> >> > >> > >> >>>> >> >> > >> > >> >>>> Bjorn, Toke: what about trying to hack aspm.c code to never do link >> >> > >> > >> >>>> retraining at GEN2 speed? And always force GEN1 speed prior link >> >> > >> > >> >>>> training? >> >> > >> > >> >>> Sounds like a plan. I poked around in aspm.c and must confess to being a >> >> > >> > >> >>> bit lost in the soup of registers ;) >> >> > >> > >> >>> >> >> > >> > >> >>> So if one of you can cook up a patch, that would be most helpful! >> >> > >> > >> >> I modified Bjorn's patch, explicitly set tls to 1 and added debug info >> >> > >> > >> >> about cls (current link speed, that what is used by aardvark). It is >> >> > >> > >> >> untested, I just tried to compile it. >> >> > >> > >> >> >> >> > >> > >> >> Can try it? >> >> > >> > >> >> >> >> > >> > >> >> diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c >> >> > >> > >> >> index 253c30cc1967..f934c0b52f41 100644 >> >> > >> > >> >> --- a/drivers/pci/pcie/aspm.c >> >> > >> > >> >> +++ b/drivers/pci/pcie/aspm.c >> >> > >> > >> >> @@ -206,6 +206,27 @@ static bool pcie_retrain_link(struct pcie_link_state *link) >> >> > >> > >> >> unsigned long end_jiffies; >> >> > >> > >> >> u16 reg16; >> >> > >> > >> >> >> >> > >> > >> >> + u32 lnkcap2; >> >> > >> > >> >> + u16 lnksta, lnkctl2, cls, tls; >> >> > >> > >> >> + >> >> > >> > >> >> + pcie_capability_read_dword(parent, PCI_EXP_LNKCAP2, &lnkcap2); >> >> > >> > >> >> + pcie_capability_read_word(parent, PCI_EXP_LNKSTA, &lnksta); >> >> > >> > >> >> + pcie_capability_read_word(parent, PCI_EXP_LNKCTL2, &lnkctl2); >> >> > >> > >> >> + cls = lnksta & PCI_EXP_LNKSTA_CLS; >> >> > >> > >> >> + tls = lnkctl2 & PCI_EXP_LNKCTL2_TLS; >> >> > >> > >> >> + >> >> > >> > >> >> + pci_info(parent, "lnkcap2 %#010x sls %#04x lnksta %#06x cls %#03x lnkctl2 %#06x tls %#03x\n", >> >> > >> > >> >> + lnkcap2, (lnkcap2 & 0x3F) >> 1, >> >> > >> > >> >> + lnksta, cls, >> >> > >> > >> >> + lnkctl2, tls); >> >> > >> > >> >> + >> >> > >> > >> >> + tls = 1; >> >> > >> > >> >> + pcie_capability_clear_and_set_word(parent, PCI_EXP_LNKCTL2, >> >> > >> > >> >> + PCI_EXP_LNKCTL2_TLS, tls); >> >> > >> > >> >> + pcie_capability_read_word(parent, PCI_EXP_LNKCTL2, &lnkctl2); >> >> > >> > >> >> + pci_info(parent, "lnkctl2 %#010x new tls %#03x\n", >> >> > >> > >> >> + lnkctl2, tls); >> >> > >> > >> >> + >> >> > >> > >> >> pcie_capability_read_word(parent, PCI_EXP_LNKCTL, ®16); >> >> > >> > >> >> reg16 |= PCI_EXP_LNKCTL_RL; >> >> > >> > >> >> pcie_capability_write_word(parent, PCI_EXP_LNKCTL, reg16); >> >> > >> > >> >> @@ -227,6 +248,8 @@ static bool pcie_retrain_link(struct pcie_link_state *link) >> >> > >> > >> >> break; >> >> > >> > >> >> msleep(1); >> >> > >> > >> >> } while (time_before(jiffies, end_jiffies)); >> >> > >> > >> >> + pci_info(parent, "lnksta %#06x new cls %#03x\n", >> >> > >> > >> >> + lnksta, (cls & PCI_EXP_LNKSTA_CLS)); >> >> > >> > >> >> return !(reg16 & PCI_EXP_LNKSTA_LT); >> >> > >> > >> >> } >> >> > >> > >> >> >> >> > >> > >> > >> >> > >> > >> > Still exhibiting the BAR update error, run tested with next--20201030 >> >> > >> > >> >> >> > >> > >> Yup, same for me :( >> >> > >> >> >> > >> I'm answering my own question. This code does not work on Omnia because >> >> > >> A38x pci-mvebu.c driver is using emulator for PCIe root bridge and it >> >> > >> does not implement PCI_EXP_LNKCTL2 and PCI_EXP_LNKCTL2 registers. So >> >> > >> code for forcing link speed has no effect on Omnia... >> >> > > >> >> > > Toke, on A38x PCIe controller it is possible to access PCI_EXP_LNKCTL2 >> >> > > register. Just access is not exported via emulated root bridge. >> >> > > >> >> > > Documentation for this PCIe controller is public, so anybody can look at >> >> > > register description. See page 571, A.7 PCI Express 2.0 Port 0 Registers >> >> > > >> >> > > http://web.archive.org/web/20200420191927/https://www.marvell.com/content/dam/marvell/en/public-collateral/embedded-processors/marvell-embedded-processors-armada-38x-functional-specifications-2015-11.pdf >> >> > > >> >> > > In drivers/pci/controller/pci-mvebu.c you can set a new value for this >> >> > > register via function call: >> >> > > >> >> > > mvebu_writel(port, val, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2); >> >> > > >> >> > > So, could you try to set PCI_EXP_LNKCTL2_TLS bits to gen1 in some hw >> >> > > init function, e.g. mvebu_pcie_setup_hw()? >> >> > > >> >> > > u32 val = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2); >> >> > > val &= ~PCI_EXP_LNKCTL2_TLS; >> >> > > val |= PCI_EXP_LNKCTL2_TLS_2_5GT; >> >> > > mvebu_writel(port, val, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2); >> >> > >> >> > I pasted this into the top of mvebu_pcie_setup_hw(), and that indeed >> >> > seems to fix things so that all three PCIE devices work even with ASPM >> >> > turned on! :) >> >> >> >> Perfect! Now I'm sure that it is same issue as in aardvark driver. >> >> >> >> I will prepare patches for both pci-aardvark.c and pci-mvebu.c to export >> >> PCI_EXP_LNKCTL2 register via emulated bridge. And so aspm.c code would >> >> be able to use Bjorn or my patch which I have sent last year. >> >> >> >> Question reminds, if this is issue with QCA wifi chip on that Compex >> >> card or it is issue with PCIe controllers, now on A38x and A3720 SoC. >> >> Note that both A38x and A3720 platforms are from Marvell, but they have >> >> different PCIe controllers (so it does not mean that both must have same >> >> hw bugs). >> > >> > Seems that this is really issue in QCA98xx chips. I have send patch >> > which adds quirk for these wifi chips: >> > >> > https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@xxxxxxxxxx/ >> >> I tried applying that, and while it does fix the ath10k card, it seems >> to break the ath9k card in the slot next to it. > > Ehm, what? I know, right?! :/ > Patch which I have sent today to mailing list calls quirk code only > for PCI device id used by QCA98xx cards. For all other cards it is > noop. So upon further investigation this seems to be unrelated to the patch. Meaning that I can't reliably get the ath9k device to work again by reverting it. And the patch does seem to fix the ath10k device, so I think that's probably good. However, the issue with ath9k does seem to be related to ASPM; if I turn that off in .config, I get the ath9k device back. So we have these cases: ASPM disabled: ath9k, ath10k and mt76 cards all work ASPM enabled, no patch: only mt76 card works ASPM enabled + patch: ath10k and mt76 cards work So IDK, maybe the ath9k card needs a quirk as well? Or the mvebu board is just generally flaky? > Can you send PCI device id of your ath9k card (lspci -nn)? Because all > my tested ath9k cards have different PCI device id. [root@omnia-arch ~]# lspci -nn 00:01.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:6820] (rev 04) 00:02.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:6820] (rev 04) 00:03.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:6820] (rev 04) 01:00.0 Network controller [0280]: Qualcomm Atheros AR9287 Wireless Network Adapter (PCI-Express) [168c:002e] (rev 01) 02:00.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter [168c:003c] >> When booting with the >> patch applied, I get this in dmesg: >> >> [ 3.556599] ath: phy0: Mac Chip Rev 0xfffc0.f is not supported by this driver > > Can you send whole dmesg log? So I can see which new err/info lines are > printed. Pasting all three cases below: ASPM disabled in kernel: [ 2.976258] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 2.983948] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 2.991502] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 2.999337] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.008418] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.017677] scsi host0: ahci-mvebu [ 3.021317] scsi host1: ahci-mvebu [ 3.024837] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 3.032784] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 3.041624] spi-nor spi0.0: s25fl164k (8192 Kbytes) [ 3.046534] 2 fixed-partitions partitions found on MTD device spi0.0 [ 3.052918] Creating 2 MTD partitions on "spi0.0": [ 3.057723] 0x000000000000-0x000000100000 : "U-Boot" [ 3.071739] 0x000000100000-0x000000800000 : "Rescue system" [ 3.092049] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.099901] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@xxxxxxxxx>. All Rights Reserved. [ 3.110165] libphy: Fixed MDIO Bus: probed [ 3.114489] tun: Universal TUN/TAP device driver, 1.6 [ 3.119943] libphy: orion_mdio_bus: probed [ 3.125168] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 3.337489] libphy: mv88e6xxx SMI: probed [ 3.348427] mvneta_bm f10c8000.bm: failed to allocate internal memory [ 3.354912] mvneta_bm: probe of f10c8000.bm failed with error -12 [ 3.361844] mvneta f1070000.ethernet eth0: Using hardware mac address d8:58:d7:00:4e:98 [ 3.370661] mvneta f1030000.ethernet eth1: Using hardware mac address d8:58:d7:00:4e:96 [ 3.379452] mvneta f1034000.ethernet eth2: Using hardware mac address d8:58:d7:00:4e:97 [ 3.382747] ata1: SATA link down (SStatus 0 SControl 300) [ 3.387737] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 3.392932] ata2: SATA link down (SStatus 0 SControl 300) [ 3.485413] ath: EEPROM regdomain sanitized [ 3.485417] ath: EEPROM regdomain: 0x64 [ 3.485421] ath: EEPROM indicates we should expect a direct regpair map [ 3.485427] ath: Country alpha2 being used: 00 [ 3.485431] ath: Regpair used: 0x64 [ 3.487037] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 3.487723] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xf08c0000, irq=61 [ 3.494787] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 3.500670] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 3.611778] pci 0000:00:03.0: enabling device (0140 -> 0142) [ 3.617534] mt76x2e 0000:03:00.0: ASIC revision: 76120044 [ 3.736545] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 [ 3.745816] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0 [ 3.754631] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258 [ 3.799430] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 4.272133] mt76x2e 0000:03:00.0: ROM patch build: 20141115060606a [ 4.279423] mt76x2e 0000:03:00.0: Firmware Version: 0.0.00 [ 4.284936] mt76x2e 0000:03:00.0: Build: 1 [ 4.289043] mt76x2e 0000:03:00.0: Build Time: 201507311614____ [ 4.311382] mt76x2e 0000:03:00.0: Firmware running! [ 4.316666] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht' [ 4.317581] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.324153] ehci-pci: EHCI PCI platform driver [ 4.328626] ehci-orion: EHCI orion driver [ 4.332765] orion-ehci f1058000.usb: EHCI Host Controller [ 4.338189] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 4.345840] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 4.381383] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 4.387686] hub 1-0:1.0: USB hub found [ 4.391487] hub 1-0:1.0: 1 port detected [ 4.395906] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.401243] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 4.408813] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.418108] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000 [ 4.424246] hub 2-0:1.0: USB hub found [ 4.428022] hub 2-0:1.0: 1 port detected [ 4.432125] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.437457] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 4.444981] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 4.451399] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.459764] hub 3-0:1.0: USB hub found [ 4.463554] hub 3-0:1.0: 1 port detected [ 4.467745] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.473091] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.480645] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.489931] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000 [ 4.496068] hub 4-0:1.0: USB hub found [ 4.499841] hub 4-0:1.0: 1 port detected [ 4.504872] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.510202] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.517734] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.524138] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.532517] hub 5-0:1.0: USB hub found [ 4.536289] hub 5-0:1.0: 1 port detected [ 4.540478] usbcore: registered new interface driver usb-storage [ 4.547239] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 4.552835] armada38x-rtc f10a3800.rtc: setting system clock to 2021-03-26T16:20:15 UTC (1616775615) [ 4.562130] i2c /dev entries driver [ 4.565923] i2c i2c-0: Not using recovery: no recover_bus() found [ 4.573058] at24 1-0054: supply vcc not found, using dummy regulator [ 4.580309] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 4.587074] i2c i2c-0: Added multiplexed i2c bus 1 [ 4.592013] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.596920] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.601835] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.606742] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.611719] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.616636] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.621758] pca953x 8-0071: supply vcc not found, using dummy regulator [ 4.628452] pca953x 8-0071: using no AI [ 4.632847] pca953x 8-0071: interrupt support not compiled in [ 4.639217] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.644095] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547 [ 4.653257] orion_wdt: Initial timeout 171 sec [ 4.657949] sdhci: Secure Digital Host Controller Interface driver [ 4.664154] sdhci: Copyright(c) Pierre Ossman [ 4.668629] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.674605] ledtrig-cpu: registered to indicate activity on CPUs [ 4.681575] marvell-cesa f1090000.crypto: CESA device successfully registered [ 4.688898] usbcore: registered new interface driver usbhid [ 4.694525] usbhid: USB HID core driver [ 4.698475] GACT probability on [ 4.701661] Mirror/redirect action on [ 4.705344] Simple TC action Loaded [ 4.708868] u32 classifier [ 4.709904] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA [ 4.711587] Performance counters on [ 4.711589] input device check on [ 4.726537] Actions configured [ 4.730425] NET: Registered protocol family 10 [ 4.735700] Segment Routing with IPv6 [ 4.739449] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.745712] NET: Registered protocol family 17 [ 4.750262] 8021q: 802.1Q VLAN Support v1.8 [ 4.754568] ThumbEE CPU extension supported. [ 4.758868] Registering SWP/SWPB emulation handler [ 4.763814] Loading compiled-in X.509 certificates [ 4.769890] Btrfs loaded, crc32c=crc32c-generic, zoned=no [ 4.776962] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 4.857571] mmc0: new high speed MMC card at address 0001 [ 4.863325] mmcblk0: mmc0:0001 H8G4a\x92 7.28 GiB [ 4.867990] mmcblk0boot0: mmc0:0001 H8G4a\x92 partition 1 4.00 MiB [ 4.884409] mmcblk0boot1: mmc0:0001 H8G4a\x92 partition 2 4.00 MiB [ 4.896614] mmcblk0rpmb: mmc0:0001 H8G4a\x92 partition 3 4.00 MiB, chardev (250:0) [ 4.905592] mmcblk0: p1 [ 4.962991] libphy: mv88e6xxx SMI: probed [ 4.967796] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 [ 5.082952] ath: EEPROM regdomain sanitized [ 5.082960] ath: EEPROM regdomain: 0x64 [ 5.082964] ath: EEPROM indicates we should expect a direct regpair map [ 5.082970] ath: Country alpha2 being used: 00 [ 5.082974] ath: Regpair used: 0x64 [ 5.616015] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=75) [ 5.651333] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=76) [ 5.679855] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=77) [ 5.715061] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=78) [ 5.745795] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=79) [ 5.762566] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode [ 5.772960] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off [ 5.780968] DSA: tree 0 setup [ 5.784683] Waiting 2 sec before mounting root device... [ 5.790133] ath: EEPROM regdomain: 0x80d0 [ 5.790138] ath: EEPROM indicates we should expect a country code [ 5.790141] ath: doing EEPROM country->regdmn map search [ 5.790143] ath: country maps to regdmn code: 0x37 [ 5.790147] ath: Country alpha2 being used: DK [ 5.790150] ath: Regpair used: 0x37 [ 5.790156] ath: regdomain 0x80d0 dynamically updated by user [ 5.790193] ath: EEPROM regdomain: 0x80d0 [ 5.790196] ath: EEPROM indicates we should expect a country code [ 5.790199] ath: doing EEPROM country->regdmn map search [ 5.790201] ath: country maps to regdmn code: 0x37 [ 5.790204] ath: Country alpha2 being used: DK [ 5.790207] ath: Regpair used: 0x37 [ 5.790211] ath: regdomain 0x80d0 dynamically updated by user [ 7.837897] BTRFS: device fsid 448334b8-1b27-4738-8118-9e70b56b1e58 devid 1 transid 13774 /dev/root scanned by swapper/0 (1) [ 7.849813] BTRFS info (device mmcblk0p1): disk space caching is enabled [ 7.856549] BTRFS info (device mmcblk0p1): has skinny extents [ 7.868764] BTRFS info (device mmcblk0p1): enabling ssd optimizations [ 7.877839] VFS: Mounted root (btrfs filesystem) on device 0:13. [ 7.884300] devtmpfs: mounted [ 7.887886] Freeing unused kernel memory: 1024K [ 7.931610] Run /sbin/init as init process [ 7.935718] with arguments: [ 7.935722] /sbin/init [ 7.935726] earlyprintk [ 7.935729] with environment: [ 7.935731] HOME=/ [ 7.935734] TERM=linux [ 8.001203] random: fast init done [ 8.361921] systemd[1]: systemd 247.3-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [ 8.384851] systemd[1]: Detected architecture arm. [ 8.512663] systemd[1]: Set hostname to <omnia-arch>. [ 8.701050] systemd-gpt-auto-generator[173]: File system behind root file system is reported by btrfs to be backed by pseudo-device /dev/root, which is not a valid userspace accessible device node. Cannot determine correct backing block device. [ 8.724725] systemd[167]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1. [ 8.940665] systemd[1]: Queued start job for default target Graphical Interface. [ 8.948762] random: systemd: uninitialized urandom read (16 bytes read) [ 8.976192] systemd[1]: Created slice system-getty.slice. [ 9.011489] random: systemd: uninitialized urandom read (16 bytes read) [ 9.019036] systemd[1]: Created slice system-modprobe.slice. [ 9.051479] random: systemd: uninitialized urandom read (16 bytes read) [ 9.058989] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 9.102304] systemd[1]: Created slice User and Session Slice. [ 9.141626] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 9.181591] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 9.221501] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 9.233245] systemd[1]: Reached target Local Encrypted Volumes. [ 9.281608] systemd[1]: Reached target Paths. [ 9.311499] systemd[1]: Reached target Remote File Systems. [ 9.351458] systemd[1]: Reached target Slices. [ 9.381494] systemd[1]: Reached target Swap. [ 9.411697] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 9.463054] systemd[1]: Listening on Process Core Dump Socket. [ 9.505727] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 9.515082] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.561786] systemd[1]: Listening on Journal Socket. [ 9.608194] systemd[1]: Listening on Network Service Netlink Socket. [ 9.653001] systemd[1]: Listening on udev Control Socket. [ 9.701707] systemd[1]: Listening on udev Kernel Socket. [ 9.751738] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 9.760158] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 9.771842] systemd[1]: Mounting Kernel Debug File System... [ 9.824052] systemd[1]: Mounting Kernel Trace File System... [ 9.864055] systemd[1]: Mounting Temporary Directory (/tmp)... [ 9.901704] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. [ 9.915840] systemd[1]: Starting Load Kernel Module configfs... [ 9.954174] systemd[1]: Starting Load Kernel Module drm... [ 9.994448] systemd[1]: Starting Load Kernel Module fuse... [ 10.038218] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 10.048741] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. [ 10.059545] systemd[1]: Starting Remount Root and Kernel File Systems... [ 10.101616] systemd[1]: Condition check resulted in Repartition Root Disk being skipped. [ 10.112555] systemd[1]: Starting Apply Kernel Variables... [ 10.154279] systemd[1]: Starting Coldplug All udev Devices... [ 10.196174] systemd[1]: Mounted Kernel Debug File System. [ 10.232075] systemd[1]: Mounted Kernel Trace File System. [ 10.271750] systemd[1]: Mounted Temporary Directory (/tmp). [ 10.311990] systemd[1]: modprobe@configfs.service: Succeeded. [ 10.318833] systemd[1]: Finished Load Kernel Module configfs. [ 10.356178] systemd[1]: modprobe@drm.service: Succeeded. [ 10.362801] systemd[1]: Finished Load Kernel Module drm. [ 10.402063] systemd[1]: modprobe@fuse.service: Succeeded. [ 10.408508] systemd[1]: Finished Load Kernel Module fuse. [ 10.442754] systemd[1]: Finished Remount Root and Kernel File Systems. [ 10.482774] systemd[1]: Finished Apply Kernel Variables. [ 10.524656] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 10.533471] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. [ 10.542901] systemd[1]: Condition check resulted in First Boot Wizard being skipped. [ 10.558481] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 10.569814] systemd[1]: Starting Load/Save Random Seed... [ 10.591724] systemd[1]: Condition check resulted in Create System Users being skipped. [ 10.604115] systemd[1]: Starting Create Static Device Nodes in /dev... [ 10.713433] systemd[1]: Finished Create Static Device Nodes in /dev. [ 10.731783] systemd[1]: Reached target Local File Systems (Pre). [ 10.751621] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped. [ 10.762698] systemd[1]: Reached target Local File Systems. [ 10.804744] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm. [ 10.851807] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped. [ 10.864572] systemd[1]: Starting Journal Service... [ 10.885604] systemd[1]: Starting Rule-based Manager for Device Events and Files... [ 10.933455] systemd[1]: Finished Coldplug All udev Devices. [ 11.003259] systemd[1]: Started Journal Service. [ 11.107515] systemd-journald[193]: Received client request to flush runtime journal. [ 12.370305] mvneta f1034000.ethernet eth2: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL) [ 12.402376] mvneta f1034000.ethernet eth2: configuring for phy/sgmii link mode [ 12.717844] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii link mode [ 12.728688] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.923038] ath9k 0000:01:00.0 wlp1s0: renamed from wlan0 [ 13.032064] random: crng init done [ 13.035500] random: 7 urandom warning(s) missed due to ratelimiting [ 13.047961] mt76x2e 0000:03:00.0 wlp3s0: renamed from wlan1 [ 13.210519] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan2 [ 13.259848] BTRFS info (device mmcblk0p1): devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by systemd-udevd (200) [ 15.521757] mvneta f1034000.ethernet eth2: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.626452] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware [ 15.648452] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready ASPM enabled, no patch: [ 1.592272] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.592280] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.592290] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe03fffff 64bit] [ 1.592298] pci 0000:02:00.0: BAR 0: error updating (0xe0200004 != 0xffffffff) [ 1.592305] pci 0000:02:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff) [ 1.592313] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0400000-0xe040ffff pref] [ 1.592320] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.592326] pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe04fffff] [ 1.592336] pci 0000:03:00.0: BAR 0: assigned [mem 0xe0600000-0xe06fffff 64bit] [ 1.592349] pci 0000:03:00.0: BAR 6: assigned [mem 0xe0700000-0xe070ffff pref] [ 1.592357] pci 0000:00:03.0: PCI bridge to [bus 03] [ 1.592363] pci 0000:00:03.0: bridge window [mem 0xe0600000-0xe07fffff] [ 1.592639] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.651773] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.651912] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.711771] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.730234] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.731099] printk: console [ttyS0] disabled [ 1.751190] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 15625000) is a 16550A [ 3.098634] printk: console [ttyS0] enabled [ 3.123524] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 31, base_baud = 15625000) is a 16550A [ 3.133234] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.140900] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.148455] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.156311] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.165396] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.174645] scsi host0: ahci-mvebu [ 3.178287] scsi host1: ahci-mvebu [ 3.181806] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 3.189747] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 3.198555] spi-nor spi0.0: s25fl164k (8192 Kbytes) [ 3.203487] 2 fixed-partitions partitions found on MTD device spi0.0 [ 3.209858] Creating 2 MTD partitions on "spi0.0": [ 3.214668] 0x000000000000-0x000000100000 : "U-Boot" [ 3.231750] 0x000000100000-0x000000800000 : "Rescue system" [ 3.238228] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.246104] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@xxxxxxxxx>. All Rights Reserved. [ 3.256368] libphy: Fixed MDIO Bus: probed [ 3.260622] tun: Universal TUN/TAP device driver, 1.6 [ 3.266077] libphy: orion_mdio_bus: probed [ 3.271350] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 3.496234] libphy: mv88e6xxx SMI: probed [ 3.507137] mvneta_bm f10c8000.bm: failed to allocate internal memory [ 3.513632] mvneta_bm: probe of f10c8000.bm failed with error -12 [ 3.520579] mvneta f1070000.ethernet eth0: Using hardware mac address d8:58:d7:00:4e:98 [ 3.529438] mvneta f1030000.ethernet eth1: Using hardware mac address d8:58:d7:00:4e:96 [ 3.532721] ata2: SATA link down (SStatus 0 SControl 300) [ 3.543677] mvneta f1034000.ethernet eth2: Using hardware mac address d8:58:d7:00:4e:97 [ 3.551400] ata1: SATA link down (SStatus 0 SControl 300) [ 3.551984] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 3.562825] ath9k 0000:01:00.0: enabling device (0000 -> 0002) [ 3.568745] ath: phy0: Mac Chip Rev 0xfffc0.f is not supported by this driver [ 3.575912] ath: phy0: Unable to initialize hardware; initialization status: -95 [ 3.583348] ath9k 0000:01:00.0: Failed to initialize device [ 3.588955] ath9k: probe of 0000:01:00.0 failed with error -95 [ 3.594889] ath10k_pci 0000:02:00.0: of_irq_parse_pci: failed with rc=134 [ 3.601924] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 3.607610] ath10k_pci 0000:02:00.0: can't change power state from D3hot to D0 (config space inaccessible) [ 3.647457] ath10k_pci 0000:02:00.0: failed to wake up device : -110 [ 3.653973] ath10k_pci: probe of 0000:02:00.0 failed with error -110 [ 3.660490] pci 0000:00:03.0: enabling device (0140 -> 0142) [ 3.666248] mt76x2e 0000:03:00.0: ASIC revision: 76120044 [ 4.322137] mt76x2e 0000:03:00.0: ROM patch build: 20141115060606a [ 4.329426] mt76x2e 0000:03:00.0: Firmware Version: 0.0.00 [ 4.334938] mt76x2e 0000:03:00.0: Build: 1 [ 4.339044] mt76x2e 0000:03:00.0: Build Time: 201507311614____ [ 4.361396] mt76x2e 0000:03:00.0: Firmware running! [ 4.366676] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht' [ 4.367557] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.374129] ehci-pci: EHCI PCI platform driver [ 4.378601] ehci-orion: EHCI orion driver [ 4.382735] orion-ehci f1058000.usb: EHCI Host Controller [ 4.388159] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 4.395807] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 4.431395] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 4.437694] hub 1-0:1.0: USB hub found [ 4.441482] hub 1-0:1.0: 1 port detected [ 4.445898] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.451233] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 4.458801] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.468077] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000 [ 4.474214] hub 2-0:1.0: USB hub found [ 4.477988] hub 2-0:1.0: 1 port detected [ 4.482079] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.487408] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 4.494934] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 4.501331] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.509702] hub 3-0:1.0: USB hub found [ 4.513483] hub 3-0:1.0: 1 port detected [ 4.517673] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.523018] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.530572] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.539846] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000 [ 4.545966] hub 4-0:1.0: USB hub found [ 4.549738] hub 4-0:1.0: 1 port detected [ 4.553885] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.559216] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.566739] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.573144] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.581515] hub 5-0:1.0: USB hub found [ 4.585287] hub 5-0:1.0: 1 port detected [ 4.589465] usbcore: registered new interface driver usb-storage [ 4.596214] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 4.601799] armada38x-rtc f10a3800.rtc: setting system clock to 2021-03-26T16:11:35 UTC (1616775095) [ 4.611086] i2c /dev entries driver [ 4.614887] i2c i2c-0: Not using recovery: no recover_bus() found [ 4.622023] at24 1-0054: supply vcc not found, using dummy regulator [ 4.629281] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 4.636062] i2c i2c-0: Added multiplexed i2c bus 1 [ 4.640975] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.645896] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.650800] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.655728] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.660632] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.665602] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.670712] pca953x 8-0071: supply vcc not found, using dummy regulator [ 4.677408] pca953x 8-0071: using no AI [ 4.681786] pca953x 8-0071: interrupt support not compiled in [ 4.688149] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.693024] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547 [ 4.701771] orion_wdt: Initial timeout 171 sec [ 4.706487] sdhci: Secure Digital Host Controller Interface driver [ 4.712694] sdhci: Copyright(c) Pierre Ossman [ 4.717166] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.723128] ledtrig-cpu: registered to indicate activity on CPUs [ 4.730073] marvell-cesa f1090000.crypto: CESA device successfully registered [ 4.737410] usbcore: registered new interface driver usbhid [ 4.743005] usbhid: USB HID core driver [ 4.746954] GACT probability on [ 4.748973] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA [ 4.750110] Mirror/redirect action on [ 4.761224] Simple TC action Loaded [ 4.764778] u32 classifier [ 4.767497] Performance counters on [ 4.771352] input device check on [ 4.775050] Actions configured [ 4.778936] NET: Registered protocol family 10 [ 4.784230] Segment Routing with IPv6 [ 4.787967] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.794228] NET: Registered protocol family 17 [ 4.798762] 8021q: 802.1Q VLAN Support v1.8 [ 4.803057] ThumbEE CPU extension supported. [ 4.807340] Registering SWP/SWPB emulation handler [ 4.812276] Loading compiled-in X.509 certificates [ 4.818281] Btrfs loaded, crc32c=crc32c-generic, zoned=no [ 4.825371] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 4.987606] mmc0: new high speed MMC card at address 0001 [ 4.992837] libphy: mv88e6xxx SMI: probed [ 4.997259] mmcblk0: mmc0:0001 H8G4a\x92 7.28 GiB [ 5.002056] mmcblk0boot0: mmc0:0001 H8G4a\x92 partition 1 4.00 MiB [ 5.008124] mmcblk0boot1: mmc0:0001 H8G4a\x92 partition 2 4.00 MiB [ 5.014160] mmcblk0rpmb: mmc0:0001 H8G4a\x92 partition 3 4.00 MiB, chardev (250:0) [ 5.022894] mmcblk0: p1 [ 5.641653] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=73) [ 5.672563] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=74) [ 5.705082] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=75) [ 5.731373] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=76) [ 5.766642] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=77) [ 5.783423] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode [ 5.793831] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off [ 5.801848] DSA: tree 0 setup [ 5.805559] Waiting 2 sec before mounting root device... [ 7.837895] BTRFS: device fsid 448334b8-1b27-4738-8118-9e70b56b1e58 devid 1 transid 13732 /dev/root scanned by swapper/0 (1) [ 7.849816] BTRFS info (device mmcblk0p1): disk space caching is enabled [ 7.856552] BTRFS info (device mmcblk0p1): has skinny extents [ 7.868426] BTRFS info (device mmcblk0p1): enabling ssd optimizations [ 7.877500] VFS: Mounted root (btrfs filesystem) on device 0:13. [ 7.883966] devtmpfs: mounted [ 7.887547] Freeing unused kernel memory: 1024K [ 7.931625] Run /sbin/init as init process [ 7.935733] with arguments: [ 7.935737] /sbin/init [ 7.935740] earlyprintk [ 7.935743] with environment: [ 7.935746] HOME=/ [ 7.935749] TERM=linux [ 8.048502] random: fast init done [ 8.365030] systemd[1]: systemd 247.3-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [ 8.388024] systemd[1]: Detected architecture arm. [ 8.462658] systemd[1]: Set hostname to <omnia-arch>. [ 8.627786] systemd-gpt-auto-generator[172]: File system behind root file system is reported by btrfs to be backed by pseudo-device /dev/root, which is not a valid userspace accessible device node. Cannot determine correct backing block device. [ 8.655604] systemd[166]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1. [ 8.881598] systemd[1]: Queued start job for default target Graphical Interface. [ 8.889617] random: systemd: uninitialized urandom read (16 bytes read) [ 8.916194] systemd[1]: Created slice system-getty.slice. [ 8.951618] random: systemd: uninitialized urandom read (16 bytes read) [ 8.959166] systemd[1]: Created slice system-modprobe.slice. [ 8.991497] random: systemd: uninitialized urandom read (16 bytes read) [ 8.998988] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 9.032326] systemd[1]: Created slice User and Session Slice. [ 9.071643] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 9.111679] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 9.151521] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 9.163271] systemd[1]: Reached target Local Encrypted Volumes. [ 9.201592] systemd[1]: Reached target Paths. [ 9.231508] systemd[1]: Reached target Remote File Systems. [ 9.271473] systemd[1]: Reached target Slices. [ 9.301510] systemd[1]: Reached target Swap. [ 9.331712] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 9.382980] systemd[1]: Listening on Process Core Dump Socket. [ 9.425820] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 9.435158] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.481817] systemd[1]: Listening on Journal Socket. [ 9.518192] systemd[1]: Listening on Network Service Netlink Socket. [ 9.563010] systemd[1]: Listening on udev Control Socket. [ 9.611715] systemd[1]: Listening on udev Kernel Socket. [ 9.661746] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 9.670165] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 9.681829] systemd[1]: Mounting Kernel Debug File System... [ 9.724106] systemd[1]: Mounting Kernel Trace File System... [ 9.764065] systemd[1]: Mounting Temporary Directory (/tmp)... [ 9.801730] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. [ 9.815900] systemd[1]: Starting Load Kernel Module configfs... [ 9.854292] systemd[1]: Starting Load Kernel Module drm... [ 9.894496] systemd[1]: Starting Load Kernel Module fuse... [ 9.938207] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 9.948767] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. [ 9.959564] systemd[1]: Starting Remount Root and Kernel File Systems... [ 10.001625] systemd[1]: Condition check resulted in Repartition Root Disk being skipped. [ 10.012531] systemd[1]: Starting Apply Kernel Variables... [ 10.054299] systemd[1]: Starting Coldplug All udev Devices... [ 10.106173] systemd[1]: Mounted Kernel Debug File System. [ 10.151975] systemd[1]: Mounted Kernel Trace File System. [ 10.201691] systemd[1]: Mounted Temporary Directory (/tmp). [ 10.242004] systemd[1]: modprobe@configfs.service: Succeeded. [ 10.248810] systemd[1]: Finished Load Kernel Module configfs. [ 10.286193] systemd[1]: modprobe@drm.service: Succeeded. [ 10.292770] systemd[1]: Finished Load Kernel Module drm. [ 10.332207] systemd[1]: modprobe@fuse.service: Succeeded. [ 10.338606] systemd[1]: Finished Load Kernel Module fuse. [ 10.372731] systemd[1]: Finished Remount Root and Kernel File Systems. [ 10.412748] systemd[1]: Finished Apply Kernel Variables. [ 10.464629] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 10.473431] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. [ 10.482779] systemd[1]: Condition check resulted in First Boot Wizard being skipped. [ 10.498346] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 10.509666] systemd[1]: Starting Load/Save Random Seed... [ 10.531781] systemd[1]: Condition check resulted in Create System Users being skipped. [ 10.543704] systemd[1]: Starting Create Static Device Nodes in /dev... [ 10.722733] systemd[1]: Finished Create Static Device Nodes in /dev. [ 10.773072] systemd[1]: Finished Coldplug All udev Devices. [ 10.811698] systemd[1]: Reached target Local File Systems (Pre). [ 10.851561] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped. [ 10.862560] systemd[1]: Reached target Local File Systems. [ 10.904738] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm. [ 10.941790] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped. [ 10.954403] systemd[1]: Starting Journal Service... [ 11.002108] systemd[1]: Starting Rule-based Manager for Device Events and Files... [ 11.104142] systemd[1]: Started Journal Service. [ 11.205698] systemd-journald[193]: Received client request to flush runtime journal. [ 12.715234] mvneta f1034000.ethernet eth2: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL) [ 12.742129] mvneta f1034000.ethernet eth2: configuring for phy/sgmii link mode [ 12.867939] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii link mode [ 12.888463] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 13.003326] mt76x2e 0000:03:00.0 wlp3s0: renamed from wlan0 [ 13.110923] random: crng init done [ 13.141526] random: 7 urandom warning(s) missed due to ratelimiting [ 13.320567] BTRFS info (device mmcblk0p1): devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by systemd-udevd (199) [ 15.911774] mvneta f1034000.ethernet eth2: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.919818] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready ASPM enabled, with patch: [ 1.631901] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.691759] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.710225] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.711090] printk: console [ttyS0] disabled [ 1.731185] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 15625000) is a 16550A [ 3.086738] printk: console [ttyS0] enabled [ 3.111636] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 31, base_baud = 15625000) is a 16550A [ 3.121337] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.129018] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.136573] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.144419] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.153514] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.162766] scsi host0: ahci-mvebu [ 3.166400] scsi host1: ahci-mvebu [ 3.169909] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 3.177861] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 3.186676] spi-nor spi0.0: s25fl164k (8192 Kbytes) [ 3.191598] 2 fixed-partitions partitions found on MTD device spi0.0 [ 3.197969] Creating 2 MTD partitions on "spi0.0": [ 3.202779] 0x000000000000-0x000000100000 : "U-Boot" [ 3.221737] 0x000000100000-0x000000800000 : "Rescue system" [ 3.228225] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.236100] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@xxxxxxxxx>. All Rights Reserved. [ 3.246357] libphy: Fixed MDIO Bus: probed [ 3.250614] tun: Universal TUN/TAP device driver, 1.6 [ 3.256068] libphy: orion_mdio_bus: probed [ 3.261289] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 3.483904] libphy: mv88e6xxx SMI: probed [ 3.494715] mvneta_bm f10c8000.bm: failed to allocate internal memory [ 3.501206] mvneta_bm: probe of f10c8000.bm failed with error -12 [ 3.508159] mvneta f1070000.ethernet eth0: Using hardware mac address d8:58:d7:00:4e:98 [ 3.516220] ata2: SATA link down (SStatus 0 SControl 300) [ 3.521683] ata1: SATA link down (SStatus 0 SControl 300) [ 3.527904] mvneta f1030000.ethernet eth1: Using hardware mac address d8:58:d7:00:4e:96 [ 3.536693] mvneta f1034000.ethernet eth2: Using hardware mac address d8:58:d7:00:4e:97 [ 3.544979] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 3.550664] ath9k 0000:01:00.0: enabling device (0000 -> 0002) [ 3.556599] ath: phy0: Mac Chip Rev 0xfffc0.f is not supported by this driver [ 3.563783] ath: phy0: Unable to initialize hardware; initialization status: -95 [ 3.571200] ath9k 0000:01:00.0: Failed to initialize device [ 3.576817] ath9k: probe of 0000:01:00.0 failed with error -95 [ 3.583038] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 3.588904] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 3.701778] pci 0000:00:03.0: enabling device (0140 -> 0142) [ 3.707530] mt76x2e 0000:03:00.0: ASIC revision: 76120044 [ 3.836545] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 [ 3.845813] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0 [ 3.854625] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258 [ 3.899415] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 4.362131] mt76x2e 0000:03:00.0: ROM patch build: 20141115060606a [ 4.369421] mt76x2e 0000:03:00.0: Firmware Version: 0.0.00 [ 4.374934] mt76x2e 0000:03:00.0: Build: 1 [ 4.379041] mt76x2e 0000:03:00.0: Build Time: 201507311614____ [ 4.401383] mt76x2e 0000:03:00.0: Firmware running! [ 4.406664] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht' [ 4.407567] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.414141] ehci-pci: EHCI PCI platform driver [ 4.418614] ehci-orion: EHCI orion driver [ 4.422749] orion-ehci f1058000.usb: EHCI Host Controller [ 4.428172] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 4.435825] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 4.471384] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 4.477701] hub 1-0:1.0: USB hub found [ 4.481498] hub 1-0:1.0: 1 port detected [ 4.485916] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.491253] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 4.498822] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.508116] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000 [ 4.514262] hub 2-0:1.0: USB hub found [ 4.518035] hub 2-0:1.0: 1 port detected [ 4.522138] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 4.527468] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 4.534993] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 4.541411] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.549785] hub 3-0:1.0: USB hub found [ 4.553574] hub 3-0:1.0: 1 port detected [ 4.557768] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.563115] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.570665] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.579950] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000 [ 4.586077] hub 4-0:1.0: USB hub found [ 4.589849] hub 4-0:1.0: 1 port detected [ 4.594849] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.600178] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.607711] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.614117] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.622494] hub 5-0:1.0: USB hub found [ 4.626265] hub 5-0:1.0: 1 port detected [ 4.630439] usbcore: registered new interface driver usb-storage [ 4.637200] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 4.642796] armada38x-rtc f10a3800.rtc: setting system clock to 2021-03-26T15:21:33 UTC (1616772093) [ 4.652088] i2c /dev entries driver [ 4.655879] i2c i2c-0: Not using recovery: no recover_bus() found [ 4.663003] at24 1-0054: supply vcc not found, using dummy regulator [ 4.670261] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 4.677027] i2c i2c-0: Added multiplexed i2c bus 1 [ 4.681962] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.686871] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.691781] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.696685] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.701657] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.706568] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.711692] pca953x 8-0071: supply vcc not found, using dummy regulator [ 4.718379] pca953x 8-0071: using no AI [ 4.722770] pca953x 8-0071: interrupt support not compiled in [ 4.729132] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.734009] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547 [ 4.743152] orion_wdt: Initial timeout 171 sec [ 4.747871] sdhci: Secure Digital Host Controller Interface driver [ 4.754077] sdhci: Copyright(c) Pierre Ossman [ 4.758547] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.764523] ledtrig-cpu: registered to indicate activity on CPUs [ 4.771498] marvell-cesa f1090000.crypto: CESA device successfully registered [ 4.778822] usbcore: registered new interface driver usbhid [ 4.784448] usbhid: USB HID core driver [ 4.788400] GACT probability on [ 4.791591] Mirror/redirect action on [ 4.795273] Simple TC action Loaded [ 4.798799] u32 classifier [ 4.799815] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA [ 4.801518] Performance counters on [ 4.801520] input device check on [ 4.801521] Actions configured [ 4.801981] NET: Registered protocol family 10 [ 4.825094] Segment Routing with IPv6 [ 4.828820] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.835086] NET: Registered protocol family 17 [ 4.839638] 8021q: 802.1Q VLAN Support v1.8 [ 4.843942] ThumbEE CPU extension supported. [ 4.848240] Registering SWP/SWPB emulation handler [ 4.853185] Loading compiled-in X.509 certificates [ 4.859289] Btrfs loaded, crc32c=crc32c-generic, zoned=no [ 4.866364] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 4.947964] mmc0: new high speed MMC card at address 0001 [ 4.953701] mmcblk0: mmc0:0001 H8G4a\x92 7.28 GiB [ 4.958373] mmcblk0boot0: mmc0:0001 H8G4a\x92 partition 1 4.00 MiB [ 4.974792] mmcblk0boot1: mmc0:0001 H8G4a\x92 partition 2 4.00 MiB [ 4.981468] mmcblk0rpmb: mmc0:0001 H8G4a\x92 partition 3 4.00 MiB, chardev (250:0) [ 4.990436] mmcblk0: p1 [ 5.045869] libphy: mv88e6xxx SMI: probed [ 5.065394] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 [ 5.182884] ath: EEPROM regdomain sanitized [ 5.182892] ath: EEPROM regdomain: 0x64 [ 5.182897] ath: EEPROM indicates we should expect a direct regpair map [ 5.182903] ath: Country alpha2 being used: 00 [ 5.182907] ath: Regpair used: 0x64 [ 5.697833] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=75) [ 5.730170] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=76) [ 5.765363] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=77) [ 5.798260] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=78) [ 5.828978] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=79) [ 5.847992] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode [ 5.858403] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off [ 5.866420] DSA: tree 0 setup [ 5.870132] Waiting 2 sec before mounting root device... [ 5.875609] ath: EEPROM regdomain: 0x80d0 [ 5.875614] ath: EEPROM indicates we should expect a country code [ 5.875617] ath: doing EEPROM country->regdmn map search [ 5.875620] ath: country maps to regdmn code: 0x37 [ 5.875624] ath: Country alpha2 being used: DK [ 5.875627] ath: Regpair used: 0x37 [ 5.875633] ath: regdomain 0x80d0 dynamically updated by user [ 7.917893] BTRFS: device fsid 448334b8-1b27-4738-8118-9e70b56b1e58 devid 1 transid 13610 /dev/root scanned by swapper/0 (1) [ 7.929810] BTRFS info (device mmcblk0p1): disk space caching is enabled [ 7.936547] BTRFS info (device mmcblk0p1): has skinny extents [ 7.948767] BTRFS info (device mmcblk0p1): enabling ssd optimizations [ 7.957822] VFS: Mounted root (btrfs filesystem) on device 0:13. [ 7.964279] devtmpfs: mounted [ 7.967862] Freeing unused kernel memory: 1024K [ 8.011610] Run /sbin/init as init process [ 8.015718] with arguments: [ 8.015722] /sbin/init [ 8.015725] earlyprintk [ 8.015728] with environment: [ 8.015731] HOME=/ [ 8.015734] TERM=linux [ 8.092110] random: fast init done [ 8.441825] systemd[1]: systemd 247.3-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [ 8.464757] systemd[1]: Detected architecture arm. [ 8.592661] systemd[1]: Set hostname to <omnia-arch>. [ 8.786365] systemd-gpt-auto-generator[173]: File system behind root file system is reported by btrfs to be backed by pseudo-device /dev/root, which is not a valid userspace accessible device node. Cannot determine correct backing block device. [ 8.810036] systemd[167]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1. [ 9.029889] systemd[1]: Queued start job for default target Graphical Interface. [ 9.038220] random: systemd: uninitialized urandom read (16 bytes read) [ 9.065479] systemd[1]: Created slice system-getty.slice. [ 9.101527] random: systemd: uninitialized urandom read (16 bytes read) [ 9.109083] systemd[1]: Created slice system-modprobe.slice. [ 9.141479] random: systemd: uninitialized urandom read (16 bytes read) [ 9.148986] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 9.182292] systemd[1]: Created slice User and Session Slice. [ 9.221625] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 9.261586] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 9.301489] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 9.313240] systemd[1]: Reached target Local Encrypted Volumes. [ 9.351600] systemd[1]: Reached target Paths. [ 9.381488] systemd[1]: Reached target Remote File Systems. [ 9.421453] systemd[1]: Reached target Slices. [ 9.451485] systemd[1]: Reached target Swap. [ 9.481688] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 9.532988] systemd[1]: Listening on Process Core Dump Socket. [ 9.575779] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 9.585118] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.621803] systemd[1]: Listening on Journal Socket. [ 9.658182] systemd[1]: Listening on Network Service Netlink Socket. [ 9.692994] systemd[1]: Listening on udev Control Socket. [ 9.731720] systemd[1]: Listening on udev Kernel Socket. [ 9.771747] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 9.780163] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 9.791835] systemd[1]: Mounting Kernel Debug File System... [ 9.834096] systemd[1]: Mounting Kernel Trace File System... [ 9.873970] systemd[1]: Mounting Temporary Directory (/tmp)... [ 9.911710] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. [ 9.925842] systemd[1]: Starting Load Kernel Module configfs... [ 9.964225] systemd[1]: Starting Load Kernel Module drm... [ 10.004524] systemd[1]: Starting Load Kernel Module fuse... [ 10.048219] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 10.058755] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. [ 10.069469] systemd[1]: Starting Remount Root and Kernel File Systems... [ 10.111602] systemd[1]: Condition check resulted in Repartition Root Disk being skipped. [ 10.122503] systemd[1]: Starting Apply Kernel Variables... [ 10.164228] systemd[1]: Starting Coldplug All udev Devices... [ 10.206094] systemd[1]: Mounted Kernel Debug File System. [ 10.241980] systemd[1]: Mounted Kernel Trace File System. [ 10.281734] systemd[1]: Mounted Temporary Directory (/tmp). [ 10.321996] systemd[1]: modprobe@configfs.service: Succeeded. [ 10.328795] systemd[1]: Finished Load Kernel Module configfs. [ 10.366145] systemd[1]: modprobe@drm.service: Succeeded. [ 10.372733] systemd[1]: Finished Load Kernel Module drm. [ 10.412110] systemd[1]: modprobe@fuse.service: Succeeded. [ 10.418547] systemd[1]: Finished Load Kernel Module fuse. [ 10.452851] systemd[1]: Finished Remount Root and Kernel File Systems. [ 10.492903] systemd[1]: Finished Apply Kernel Variables. [ 10.534693] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 10.543506] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. [ 10.552850] systemd[1]: Condition check resulted in First Boot Wizard being skipped. [ 10.568407] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 10.579654] systemd[1]: Starting Load/Save Random Seed... [ 10.601715] systemd[1]: Condition check resulted in Create System Users being skipped. [ 10.613507] systemd[1]: Starting Create Static Device Nodes in /dev... [ 10.743498] systemd[1]: Finished Create Static Device Nodes in /dev. [ 10.762086] systemd[1]: Reached target Local File Systems (Pre). [ 10.801636] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped. [ 10.812817] systemd[1]: Reached target Local File Systems. [ 10.854718] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm. [ 10.891763] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped. [ 10.904350] systemd[1]: Starting Journal Service... [ 10.945329] systemd[1]: Starting Rule-based Manager for Device Events and Files... [ 10.993388] systemd[1]: Finished Coldplug All udev Devices. [ 11.039498] systemd[1]: Started Journal Service. [ 11.155201] systemd-journald[193]: Received client request to flush runtime journal. [ 12.440807] mvneta f1034000.ethernet eth2: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL) [ 12.457437] mvneta f1034000.ethernet eth2: configuring for phy/sgmii link mode [ 12.536401] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii link mode [ 12.551575] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.731311] ath10k_pci 0000:02:00.0 wlp2s0: renamed from wlan1 [ 12.893504] BTRFS info (device mmcblk0p1): devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by systemd-udevd (202) [ 12.922368] mt76x2e 0000:03:00.0 wlp3s0: renamed from wlan0 [ 13.451476] random: crng init done [ 13.454898] random: 7 urandom warning(s) missed due to ratelimiting [ 15.550016] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware [ 15.591776] mvneta f1034000.ethernet eth2: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.599825] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready >> Could there be some kind of data corruption in play here making the >> driver think the chip revision is wrong, or something like that? If I >> boot the same kernel without the patch applied, the ath9k initialisation >> works fine, but obviously the ath10k is then still broken... > > There is something really strange. > > Can you add debug log into pcie_change_tls_to_gen1() function to check > for which card is this function called? Erm, it looks like it's never called? I added this: diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c index ea5bdf6107f6..794c682d4bd3 100644 --- a/drivers/pci/pcie/aspm.c +++ b/drivers/pci/pcie/aspm.c @@ -198,6 +198,9 @@ static int pcie_change_tls_to_gen1(struct pci_dev *parent) u32 reg32; int ret; + printk("pcie_change_tls_to_getn1() called for device %x:%x:%x\n", + parent->device, parent->subsystem_vendor, parent->subsystem_device); + /* Check if link speed can be forced to 2.5 GT/s */ pcie_capability_read_dword(parent, PCI_EXP_LNKCAP2, ®32); if (!(reg32 & PCI_EXP_LNKCAP2_SLS_2_5GB)) { But 'dmesg | grep called' returns nothing... > Are you testing this new patch with or without changes to > mvebu_pcie_setup_hw() function? I applied your patch on top of latest mac80211-next, which right now is this commit: https://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next.git/commit/?id=4b837ad53be2ab100dfaa99dc73a9443a8a2392d -Toke
