Re: [RESEND PATCH V6 2/2] PCI: sprd: Add support for Unisoc SoCs' PCIe controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Mar 22, 2021 at 05:18:31PM +0800, Chunyan Zhang wrote:
> From: Hongtao Wu <billows.wu@xxxxxxxxxx>
> 
> This series adds PCIe controller driver for Unisoc SoCs.
> This controller is based on DesignWare PCIe IP.
> 
> Signed-off-by: Hongtao Wu <billows.wu@xxxxxxxxxx>
> Signed-off-by: Chunyan Zhang <zhang.lyra@xxxxxxxxx>
> ---
>  drivers/pci/controller/dwc/Kconfig     |  12 +
>  drivers/pci/controller/dwc/Makefile    |   1 +
>  drivers/pci/controller/dwc/pcie-sprd.c | 292 +++++++++++++++++++++++++
>  3 files changed, 305 insertions(+)
>  create mode 100644 drivers/pci/controller/dwc/pcie-sprd.c
> 
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 22c5529e9a65..61f0b79f963d 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -318,4 +318,16 @@ config PCIE_AL
>  	  required only for DT-based platforms. ACPI platforms with the
>  	  Annapurna Labs PCIe controller don't need to enable this.
>  
> +config PCIE_SPRD

Maybe you want PCIE_SPRD_HOST for this one so there's room for a
PCIE_SPRD_EP someday?

> +	tristate "Unisoc PCIe controller - Host Mode"
> +	depends on ARCH_SPRD || COMPILE_TEST
> +	depends on PCI_MSI_IRQ_DOMAIN
> +	select PCIE_DW_HOST
> +	help
> +	  Unisoc PCIe controller uses the DesignWare core. It can be configured
> +	  as an Endpoint (EP) or a Root complex (RC). In order to enable host
> +	  mode (the controller works as RC), PCIE_SPRD must be selected.
> +	  Say Y or M here if you want to PCIe RC controller support on Unisoc
> +	  SoCs.
> +
>  endmenu
> diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> index a751553fa0db..eb546e97c14a 100644
> --- a/drivers/pci/controller/dwc/Makefile
> +++ b/drivers/pci/controller/dwc/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_PCI_MESON) += pci-meson.o
>  obj-$(CONFIG_PCIE_TEGRA194) += pcie-tegra194.o
>  obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
>  obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
> +obj-$(CONFIG_PCIE_SPRD) += pcie-sprd.o
>  
>  # The following drivers are for devices that use the generic ACPI
>  # pci_root.c driver but don't support standard ECAM config access.
> diff --git a/drivers/pci/controller/dwc/pcie-sprd.c b/drivers/pci/controller/dwc/pcie-sprd.c
> new file mode 100644
> index 000000000000..2ccb99eda24f
> --- /dev/null
> +++ b/drivers/pci/controller/dwc/pcie-sprd.c
> @@ -0,0 +1,292 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * PCIe host controller driver for Unisoc SoCs
> + *
> + * Copyright (C) 2020-2021 Unisoc, Inc.
> + *
> + * Author: Hongtao Wu <Billows.Wu@xxxxxxxxxx>
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +#include "pcie-designware.h"
> +
> +/* aon apb syscon */
> +#define IPA_ACCESS_CFG		0xcd8
> +#define  AON_ACCESS_PCIE_EN	BIT(1)
> +
> +/* pmu apb syscon */
> +#define SNPS_PCIE3_SLP_CTRL	0xac
> +#define  PERST_N_ASSERT		BIT(1)
> +#define  PERST_N_AUTO_EN	BIT(0)
> +#define PD_PCIE_CFG_0		0x3e8
> +#define  PCIE_FORCE_SHUTDOWN	BIT(25)
> +
> +#define PCIE_SS_REG_BASE		0xE00

Pick uppercase or lowercase for your hex constants and use it
consistently.

> +#define APB_CLKFREQ_TIMEOUT		0x4
> +#define  BUSERR_EN			BIT(12)
> +#define  APB_TIMER_DIS			BIT(10)
> +#define  APB_TIMER_LIMIT		GENMASK(31, 16)
> +
> +#define PE0_GEN_CTRL_3			0x58
> +#define  LTSSM_EN			BIT(0)
> +
> +struct sprd_pcie_soc_data {
> +	u32 syscon_offset;
> +};
> +
> +static const struct sprd_pcie_soc_data ums9520_syscon_data = {
> +	.syscon_offset = 0x1000,	/* The offset of set/clear register */
> +};
> +
> +struct sprd_pcie {
> +	u32 syscon_offset;
> +	struct device	*dev;
> +	struct dw_pcie	*pci;
> +	struct regmap	*aon_map;
> +	struct regmap	*pmu_map;
> +	const struct sprd_pcie_soc_data *socdata;
> +};
> +
> +enum sprd_pcie_syscon_type {
> +	normal_syscon,		/* it's not a set/clear register */
> +	set_syscon,		/* set a set/clear register */
> +	clr_syscon,		/* clear a set/clear register */
> +};
> +
> +static void sprd_pcie_buserr_enable(struct dw_pcie *pci)
> +{
> +	u32 val;
> +
> +	val = dw_pcie_readl_dbi(pci, PCIE_SS_REG_BASE + APB_CLKFREQ_TIMEOUT);
> +	val &= ~APB_TIMER_DIS;
> +	val |= BUSERR_EN;
> +	val |= APB_TIMER_LIMIT & (0x1f4 << 16);
> +	dw_pcie_writel_dbi(pci, PCIE_SS_REG_BASE + APB_CLKFREQ_TIMEOUT, val);
> +}
> +
> +static void sprd_pcie_ltssm_enable(struct dw_pcie *pci, bool enable)
> +{
> +	u32 val;
> +
> +	val = dw_pcie_readl_dbi(pci, PCIE_SS_REG_BASE + PE0_GEN_CTRL_3);
> +	if (enable)
> +		dw_pcie_writel_dbi(pci, PCIE_SS_REG_BASE + PE0_GEN_CTRL_3,
> +				   val | LTSSM_EN);
> +	else
> +		dw_pcie_writel_dbi(pci, PCIE_SS_REG_BASE + PE0_GEN_CTRL_3,
> +				   val & ~LTSSM_EN);
> +}
> +
> +static int sprd_pcie_syscon_set(struct sprd_pcie *ctrl, struct regmap *map,
> +				u32 reg, u32 mask, u32 val,
> +				enum sprd_pcie_syscon_type type)
> +{
> +	int ret = 0;
> +	u32 read_val;
> +	u32 offset = ctrl->syscon_offset;
> +	struct device *dev = ctrl->pci->dev;
> +
> +	/*
> +	 * Each set/clear register has three registers:
> +	 * reg:			base register
> +	 * reg + offset:	set register
> +	 * reg + offset * 2:	clear register
> +	 */
> +	switch (type) {
> +	case normal_syscon:
> +		ret = regmap_read(map, reg, &read_val);
> +		if (ret) {
> +			dev_err(dev, "failed to read register 0x%x\n", reg);
> +			return ret;
> +		}
> +		read_val &= ~mask;
> +		read_val |= (val & mask);
> +		ret = regmap_write(map, reg, read_val);
> +		break;
> +	case set_syscon:
> +		reg = reg + offset;
> +		ret = regmap_write(map, reg, val);
> +		break;
> +	case clr_syscon:
> +		reg = reg + offset * 2;
> +		ret = regmap_write(map, reg, val);
> +		break;
> +	default:
> +		break;

Unnecessary default case.

> +	}
> +
> +	if (ret)
> +		dev_err(dev, "failed to write register 0x%x\n", reg);
> +
> +	return ret;
> +}
> +
> +static int sprd_pcie_perst_assert(struct sprd_pcie *ctrl)
> +{
> +	return sprd_pcie_syscon_set(ctrl, ctrl->pmu_map, SNPS_PCIE3_SLP_CTRL,
> +				    PERST_N_ASSERT, PERST_N_ASSERT, set_syscon);
> +}
> +
> +static int sprd_pcie_perst_deassert(struct sprd_pcie *ctrl)
> +{
> +	int ret;
> +
> +	ret = sprd_pcie_syscon_set(ctrl, ctrl->pmu_map, SNPS_PCIE3_SLP_CTRL,
> +				   PERST_N_ASSERT, 0, clr_syscon);
> +	usleep_range(2000, 3000);

It'd be nice to have a spec reference for this delay.

> +	return ret;
> +}
> +
> +static int sprd_pcie_power_on(struct platform_device *pdev)

You could pass in the "struct sprd_pcie *" here since the caller has
that already.

> +{
> +	int ret;
> +	struct sprd_pcie *ctrl = platform_get_drvdata(pdev);
> +	struct dw_pcie *pci = ctrl->pci;
> +
> +	ret = sprd_pcie_syscon_set(ctrl, ctrl->aon_map, PD_PCIE_CFG_0,
> +				   PCIE_FORCE_SHUTDOWN, 0, clr_syscon);
> +	if (ret)
> +		return ret;
> +
> +	ret = sprd_pcie_syscon_set(ctrl, ctrl->aon_map, IPA_ACCESS_CFG,
> +				   AON_ACCESS_PCIE_EN, AON_ACCESS_PCIE_EN,
> +				   set_syscon);
> +	if (ret)
> +		return ret;
> +
> +	ret = sprd_pcie_perst_deassert(ctrl);
> +	if (ret)
> +		return ret;
> +
> +	sprd_pcie_buserr_enable(pci);
> +	sprd_pcie_ltssm_enable(pci, true);
> +
> +	return ret;
> +}
> +
> +static int sprd_pcie_power_off(struct platform_device *pdev)

And here.  Caller would have to look up platform_get_drvdata(), as is
done in other drivers.

> +{
> +	struct sprd_pcie *ctrl = platform_get_drvdata(pdev);
> +	struct dw_pcie *pci = ctrl->pci;
> +
> +	sprd_pcie_ltssm_enable(pci, false);
> +
> +	sprd_pcie_perst_assert(ctrl);
> +	sprd_pcie_syscon_set(ctrl, ctrl->aon_map, PD_PCIE_CFG_0,
> +			     PCIE_FORCE_SHUTDOWN, PCIE_FORCE_SHUTDOWN,
> +			     set_syscon);
> +	sprd_pcie_syscon_set(ctrl, ctrl->aon_map, IPA_ACCESS_CFG,
> +			     AON_ACCESS_PCIE_EN, 0, clr_syscon);
> +
> +	return 0;
> +}
> +
> +static int sprd_add_pcie_port(struct platform_device *pdev)

And here.  Look at the other drivers in drivers/pci/controller/dwc/
and make yours as much like them as possible.  This is not the place
for innovation.

> +{
> +	struct sprd_pcie *ctrl = platform_get_drvdata(pdev);
> +	struct dw_pcie *pci = ctrl->pci;
> +	struct pcie_port *pp = &pci->pp;
> +
> +	return dw_pcie_host_init(pp);
> +}
> +
> +static int sprd_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct sprd_pcie *ctrl;
> +	struct dw_pcie *pci;
> +	int ret;
> +
> +	ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
> +	if (!ctrl)
> +		return -ENOMEM;
> +
> +	ctrl->socdata =
> +		(struct sprd_pcie_soc_data *)of_device_get_match_data(dev);

Unnecessary cast.

It doesn't look like you even need to save this pointer in the struct
sprd_pcie.  You use it below to get syscon_offset, but never reference
it after this function.

> +	if (!ctrl->socdata) {
> +		dev_warn(dev,
> +			 "using the default set/clear register offset address");
> +		ctrl->syscon_offset = 0x1000;
> +	}
> +	ctrl->syscon_offset = ctrl->socdata->syscon_offset;
> +
> +	ctrl->aon_map = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							"sprd, regmap-aon");
> +	if (IS_ERR(ctrl->aon_map)) {
> +		dev_err(dev, "failed to get syscon regmap aon\n");

I think it's worth mentioning the exact string ("sprd, regmap-aon")
you were looking for.  Also below.

> +		ret = PTR_ERR(ctrl->aon_map);
> +		goto err;
> +	}
> +
> +	ctrl->pmu_map = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							"sprd, regmap-pmu");
> +	if (IS_ERR(ctrl->pmu_map)) {
> +		dev_err(dev, "failed to get syscon regmap pmu\n");
> +		ret = PTR_ERR(ctrl->pmu_map);
> +		goto err;
> +	}
> +
> +	pci = ctrl->pci;
> +	pci->dev = dev;
> +
> +	platform_set_drvdata(pdev, ctrl);
> +
> +	ret = sprd_pcie_power_on(pdev);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to power on, return %d\n",
> +			ret);
> +		goto err_power_off;
> +	}
> +
> +	ret = sprd_add_pcie_port(pdev);
> +	if (ret) {
> +		dev_warn(dev, "failed to initialize RC controller\n");
> +		return ret;

You power off for the previous error but not this one?

> +	}
> +
> +	return 0;
> +
> +err_power_off:
> +	sprd_pcie_power_off(pdev);
> +err:
> +	return ret;
> +}
> +
> +static int sprd_pcie_remove(struct platform_device *pdev)
> +{
> +	sprd_pcie_power_off(pdev);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id sprd_pcie_of_match[] = {
> +	{
> +		.compatible = "sprd,ums9520-pcie",
> +		.data  = &ums9520_syscon_data,
> +	},
> +	{},
> +};
> +
> +static struct platform_driver sprd_pcie_driver = {
> +	.probe = sprd_pcie_probe,
> +	.remove = sprd_pcie_remove,
> +	.driver = {
> +		.name = "sprd-pcie",
> +		.of_match_table = sprd_pcie_of_match,
> +	},
> +};
> +module_platform_driver(sprd_pcie_driver);
> +
> +MODULE_DESCRIPTION("Unisoc PCIe host controller driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.25.1
> 



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux