Re: [PATCH v2 2/5] arm64: qcom: dts: qrb5165-rb5: add qca6391 power device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu 28 Jan 11:52 CST 2021, Dmitry Baryshkov wrote:

> Add qca6391 to device tree as a way to provide power domain to WiFi and
> BT parts of the chip.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 61 ++++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> index 8aebc3660b11..2b0c1cc9333b 100644
> --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> @@ -151,6 +151,23 @@ vreg_s4a_1p8: vreg-s4a-1p8 {
>  		regulator-max-microvolt = <1800000>;
>  		regulator-always-on;
>  	};
> +
> +	qca6391: qca6391 {
> +		compatible = "qcom,qca6390";
> +		#power-domain-cells = <0>;
> +
> +		vddaon-supply = <&vreg_s6a_0p95>;
> +		vddpmu-supply = <&vreg_s2f_0p95>;
> +		vddrfa1-supply = <&vreg_s2f_0p95>;
> +		vddrfa2-supply = <&vreg_s8c_1p3>;
> +		vddrfa3-supply = <&vreg_s5a_1p9>;
> +		vddpcie1-supply = <&vreg_s8c_1p3>;
> +		vddpcie2-supply = <&vreg_s5a_1p9>;
> +		vddio-supply = <&vreg_s4a_1p8>;
> +		pinctrl-names = "default", "active";
> +		pinctrl-0 = <&wlan_default_state &bt_default_state>;
> +		pinctrl-1 = <&wlan_active_state &bt_active_state>;

I dislike the use of pinctrl states for toggling the level of the gpio
and would prefer that you use the gpio binding and api for this instead.

> +	};
>  };
>  
>  &adsp {
> @@ -1013,6 +1030,28 @@ &tlmm {
>  		"HST_WLAN_UART_TX",
>  		"HST_WLAN_UART_RX";
>  
> +	bt_default_state: bt-default-state {

Are you sure you need to drive the BT_EN pin in order to have WiFi
working? On QCA6174 I believe the "WL_EN" was actually RESET_N and BT_EN
was actually "blueooth enable" - so we wired that in the bluetooth node
instead.

> +		bt-en {
> +			pins = "gpio21";
> +			function = "gpio";
> +
> +			drive-strength = <16>;
> +			output-low;
> +			bias-pull-up;
> +		};
> +	};
> +
> +	bt_active_state: bt-active-state {
> +		bt-en {
> +			pins = "gpio21";
> +			function = "gpio";
> +
> +			drive-strength = <16>;
> +			output-high;
> +			bias-pull-up;
> +		};
> +	};
> +
>  	lt9611_irq_pin: lt9611-irq {
>  		pins = "gpio63";
>  		function = "gpio";
> @@ -1119,6 +1158,28 @@ sdc2_card_det_n: sd-card-det-n {
>  		function = "gpio";
>  		bias-pull-up;
>  	};
> +
> +	wlan_default_state: wlan-default-state {

JFYI. You don't need this "dummy" subnode, you can put the properties
directly in the state node.

Regards,
Bjorn

> +		wlan-en {
> +			pins = "gpio20";
> +			function = "gpio";
> +
> +			drive-strength = <16>;
> +			output-low;
> +			bias-pull-up;
> +		};
> +	};
> +
> +	wlan_active_state: wlan-active-state {
> +		wlan-en {
> +			pins = "gpio20";
> +			function = "gpio";
> +
> +			drive-strength = <16>;
> +			output-high;
> +			bias-pull-up;
> +		};
> +	};
>  };
>  
>  &uart12 {
> -- 
> 2.29.2
> 



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux