Hi Greg,
On Mon, Nov 9, 2020 at 17:31:8, Greg Kroah-Hartman
<gregkh@xxxxxxxxxxxxxxxxxxx> wrote:
> On Thu, Oct 29, 2020 at 08:13:36PM +0100, Gustavo Pimentel wrote:
> > Add Synopsys DesignWare xData IP driver. This driver enables/disables
> > the PCI traffic generator module pertain to the Synopsys DesignWare
> > prototype.
> >
> > Signed-off-by: Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx>
> > ---
> > drivers/misc/dw-xdata-pcie.c | 395 +++++++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 395 insertions(+)
> > create mode 100644 drivers/misc/dw-xdata-pcie.c
> >
> > diff --git a/drivers/misc/dw-xdata-pcie.c b/drivers/misc/dw-xdata-pcie.c
> > new file mode 100644
> > index 00000000..b529dae
> > --- /dev/null
> > +++ b/drivers/misc/dw-xdata-pcie.c
> > @@ -0,0 +1,395 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (c) 2020 Synopsys, Inc. and/or its affiliates.
> > + * Synopsys DesignWare xData driver
> > + *
> > + * Author: Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx>
> > + */
> > +
> > +#include <linux/pci-epf.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/device.h>
> > +#include <linux/delay.h>
> > +#include <linux/pci.h>
> > +
> > +#define DW_XDATA_EP_MEM_OFFSET 0x8000000
> > +
> > +static DEFINE_MUTEX(xdata_lock);
> > +
> > +struct dw_xdata_pcie_data {
> > + /* xData registers location */
> > + enum pci_barno rg_bar;
> > + off_t rg_off;
> > + size_t rg_sz;
> > +};
> > +
> > +static const struct dw_xdata_pcie_data snps_edda_data = {
> > + /* xData registers location */
> > + .rg_bar = BAR_0,
> > + .rg_off = 0x00000000, /* 0 Kbytes */
> > + .rg_sz = 0x0000012c, /* 300 bytes */
> > +};
> > +
> > +static int dw_xdata_command_set(const char *val, const struct kernel_param *kp);
> > +static const struct kernel_param_ops xdata_command_ops = {
> > + .set = dw_xdata_command_set,
> > +};
> > +
> > +static char command;
> > +module_param_cb(command, &xdata_command_ops, &command, 0644);
> > +MODULE_PARM_DESC(command, "xData command");
>
> Please do not add new module parameters. This is not the 1990's, we
> have better ways of getting data into a driver.
Ok, I'll move this towards into the future, lol I'll use debugfs instead.
>
> > +
> > +static struct pci_dev *priv;
>
> You are only going to support one PCI device in the system at once?
> That's not needed, again, this isn't the 1990's, please use
> device-specific data and you will be fine, no "global" variables needed.
>
> > +
> > +union dw_xdata_control_reg {
> > + u32 reg;
> > + struct {
> > + u32 doorbell : 1; /* 00 */
> > + u32 is_write : 1; /* 01 */
> > + u32 length : 12; /* 02..13 */
> > + u32 is_64 : 1; /* 14 */
> > + u32 ep : 1; /* 15 */
> > + u32 pattern_inc : 1; /* 16 */
> > + u32 ie : 1; /* 17 */
> > + u32 no_addr_inc : 1; /* 18 */
> > + u32 trigger : 1; /* 19 */
> > + u32 _reserved0 : 12; /* 20..31 */
> > + };
> > +} __packed;
>
> What is the endian-ness of these structures? That needs to be defined
> somewhere, right?
What you suggest? Use __le32 instead of u32? Or some comment referring
the expected endianness?
>
> > +
> > +union dw_xdata_status_reg {
> > + u32 reg;
> > + struct {
> > + u32 done : 1; /* 00 */
> > + u32 _reserved0 : 15; /* 01..15 */
> > + u32 version : 16; /* 16..31 */
> > + };
> > +} __packed;
> > +
> > +union dw_xdata_xperf_control_reg {
> > + u32 reg;
> > + struct {
> > + u32 _reserved0 : 4; /* 00..03 */
> > + u32 reset : 1; /* 04 */
> > + u32 enable : 1; /* 05 */
> > + u32 _reserved1 : 26; /* 06..31 */
> > + };
> > +} __packed;
> > +
> > +union _addr {
> > + u64 reg;
> > + struct {
> > + u32 lsb;
> > + u32 msb;
> > + };
> > +};
> > +
> > +struct dw_xdata_regs {
> > + union _addr addr; /* 0x000..0x004 */
> > + u32 burst_cnt; /* 0x008 */
> > + u32 control; /* 0x00c */
> > + u32 pattern; /* 0x010 */
> > + u32 status; /* 0x014 */
> > + u32 RAM_addr; /* 0x018 */
> > + u32 RAM_port; /* 0x01c */
> > + u32 _reserved0[14]; /* 0x020..0x054 */
> > + u32 perf_control; /* 0x058 */
> > + u32 _reserved1[41]; /* 0x05c..0x0fc */
> > + union _addr wr_cnt; /* 0x100..0x104 */
> > + union _addr rd_cnt; /* 0x108..0x10c */
> > +} __packed;
>
> Why packed? Does this cross the user/kernel boundry? If so, please use
> the correct data types for the (__u32 not u32).
The idea behind this was to be a *mask* of the HW registers. By using the
packed attribute would ensure that the struct would be matching with what
is defined on the HW.
Since the used unions definitions are already packed, maybe this packed
attribute on this structure is not needed. What this what you meant?
>
>
> > +
> > +struct dw_xdata_region {
> > + phys_addr_t paddr; /* physical address */
> > + void __iomem *vaddr; /* virtual address */
> > + size_t sz; /* size */
> > +};
> > +
> > +struct dw_xdata {
> > + struct dw_xdata_region rg_region; /* registers */
> > + size_t max_wr_len; /* max xfer len */
> > + size_t max_rd_len; /* max xfer len */
> > +};
> > +
> > +static inline struct dw_xdata_regs __iomem *__dw_regs(struct dw_xdata *dw)
> > +{
> > + return dw->rg_region.vaddr;
> > +}
> > +
> > +#define SET(dw, name, value) \
> > + writel(value, &(__dw_regs(dw)->name))
> > +
> > +#define GET(dw, name) \
> > + readl(&(__dw_regs(dw)->name))
>
> Just write out readl() and writel() in the driver, it makes more sense
> to anyone trying to read the code.
Ok, that's curious. I made this exactly to turn the code more readable.
I'm okay to put like you said, no problem.
>
> > +
> > +#ifdef CONFIG_64BIT
> > +#define SET_64(dw, name, value) \
> > + writel(value, &(__dw_regs(dw)->name))
> > +
> > +#define GET_64(dw, name) \
> > + readq(&(__dw_regs(dw)->name))
> > +#endif /* CONFIG_64BIT */
>
> No need for this #ifdef, right?
>
>
> > +
> > +static void dw_xdata_stop(struct pci_dev *pdev)
> > +{
> > + struct dw_xdata *dw = pci_get_drvdata(pdev);
> > + u32 tmp = GET(dw, burst_cnt);
> > +
> > + if (tmp & 0x80000000) {
> > + tmp &= 0x7fffffff;
> > + SET(dw, burst_cnt, tmp);
> > + }
> > +}
> > +
> > +static void dw_xdata_start(struct pci_dev *pdev, bool write)
> > +{
> > + struct dw_xdata *dw = pci_get_drvdata(pdev);
> > + union dw_xdata_control_reg control;
> > + union dw_xdata_status_reg status;
> > +
> > + /* Stop first if xfer in progress */
> > + dw_xdata_stop(pdev);
> > +
> > + /* Clear status register */
> > + SET(dw, status, 0x0);
> > +
> > + /* Burst count register set for continuous until stopped */
> > + SET(dw, burst_cnt, 0x80001001);
> > +
> > + /* Pattern register */
> > + SET(dw, pattern, 0x0);
> > +
> > + /* Control register */
> > + control.reg = 0x0;
> > + control.doorbell = true;
> > + control.is_write = write;
> > + if (write)
> > + control.length = dw->max_wr_len;
> > + else
> > + control.length = dw->max_rd_len;
> > + control.pattern_inc = true;
> > + control.no_addr_inc = true;
> > + SET(dw, control, control.reg);
> > +
> > + usleep_range(100, 150);
> > +
> > + status.reg = GET(dw, status);
> > + if (!status.done)
> > + pci_info(pdev, "xData: started %s direction\n",
> > + write ? "write" : "read");
>
> Don't be noisy if all is well. You have a lot of "debugging" messages
> in this driver, please drop them all down to the debug level, or just
> remove them.
I understand and I agree with that, but this driver will be only used to
assist a HW bring up. It's focus will be only on FPGA prototype
solutions, restricted to only some cases. This help messages will be
important for a HW design or a solutions tester to find a problem root
cause.
In this case can this messages be an exception to the rule?
>
>
> > +}
> > +
> > +static u64 dw_xdata_perf_meas(struct pci_dev *pdev, u64 *wr, u64 *rd)
> > +{
> > + struct dw_xdata *dw = pci_get_drvdata(pdev);
> > +
> > + #ifdef CONFIG_64BIT
> > + *wr = GET_64(dw, wr_cnt.reg);
> > +
> > + *rd = GET_64(dw, rd_cnt.reg);
> > + #else /* CONFIG_64BIT */
> > + *wr = GET(dw, wr_cnt.msb);
> > + *wr <<= 32;
> > + *wr |= GET(dw, wr_cnt.lsb);
> > +
> > + *rd = GET(dw, rd_cnt.msb);
> > + *rd <<= 32;
> > + *rd |= GET(dw, rd_cnt.lsb);
> > + #endif /* CONFIG_64BIT */
> > +
> > + return jiffies;
>
> Why are you returning jiffies???
The goal of this function was to acquire the number of packets on a
determine instant, returning jiffies was a pretty way of having all the
info grouped. But I'll move this outside of the function.
>
>
> > +}
> > +
> > +static u64 dw_xdata_perf_diff(u64 *m1, u64 *m2, u64 time)
> > +{
> > + u64 rate;
> > +
> > + rate = (*m1 - *m2);
> > + rate *= (1000 * 1000 * 1000);
> > + rate >>= 20;
> > + rate = DIV_ROUND_CLOSEST_ULL(rate, time);
> > +
> > + return rate;
> > +}
> > +
> > +static void dw_xdata_perf(struct pci_dev *pdev)
> > +{
> > + struct dw_xdata *dw = pci_get_drvdata(pdev);
> > + union dw_xdata_xperf_control_reg control;
> > + u64 wr[2], rd[2], time[2], rate[2], diff;
> > +
> > + /* First measurement */
> > + control.reg = 0x0;
> > + control.enable = false;
> > + SET(dw, perf_control, control.reg);
> > + time[0] = dw_xdata_perf_meas(pdev, &wr[0], &rd[0]);
> > + control.enable = true;
> > + SET(dw, perf_control, control.reg);
> > +
> > + /* Delay 100ms */
> > + mdelay(100);
> > +
> > + /* Second measurement */
> > + control.reg = 0x0;
> > + control.enable = false;
> > + SET(dw, perf_control, control.reg);
> > + time[1] = dw_xdata_perf_meas(pdev, &wr[1], &rd[1]);
> > + control.enable = true;
> > + SET(dw, perf_control, control.reg);
> > +
> > + /* Calculations */
> > + diff = jiffies_to_nsecs(time[1] - time[0]);
> > +
> > + /* Write performance */
> > + rate[0] = dw_xdata_perf_diff(&wr[1], &wr[0], diff);
> > +
> > + /* Read performance */
> > + rate[1] = dw_xdata_perf_diff(&rd[1], &rd[0], diff);
> > +
> > + pci_info(pdev,
> > + "xData: time=%llu us, write=%llu MB/s, read=%llu MB/s\n",
> > + diff, rate[0], rate[1]);
>
> Again, be quiet.
>
> > +}
> > +
> > +static int dw_xdata_command_set(const char *val, const struct kernel_param *kp)
> > +{
> > + int ret = -EBUSY;
> > +
> > + mutex_lock(&xdata_lock);
> > + if (!priv)
> > + goto err;
> > +
> > + ret = param_set_charp(val, kp);
> > + if (ret)
> > + goto err;
> > +
> > + switch (*val) {
> > + case 'w':
> > + case 'W':
> > + pci_info(priv, "xData: requested write transfer\n");
> > + dw_xdata_start(priv, true);
> > + break;
> > + case 'r':
> > + case 'R':
> > + pci_info(priv, "xData: requested read transfer\n");
> > + dw_xdata_start(priv, false);
> > + break;
> > + case 'p':
> > + case 'P':
> > + pci_info(priv, "xData: requested performance analysis\n");
> > + dw_xdata_perf(priv);
> > + break;
> > + default:
> > + pci_info(priv, "xData: requested stop any transfer\n");
> > + dw_xdata_stop(priv);
> > + break;
> > + }
> > +
> > +err:
> > + mutex_unlock(&xdata_lock);
> > +
> > + return ret;
> > +}
> > +
> > +static int dw_xdata_pcie_probe(struct pci_dev *pdev,
> > + const struct pci_device_id *pid)
> > +{
> > + const struct dw_xdata_pcie_data *pdata = (void *)pid->driver_data;
> > + struct device *dev = &pdev->dev;
> > + struct dw_xdata *dw;
> > + u64 addr;
> > + int err;
> > +
> > + priv = NULL;
> > +
> > + /* Enable PCI device */
> > + err = pcim_enable_device(pdev);
> > + if (err) {
> > + pci_err(pdev, "enabling device failed\n");
> > + return err;
> > + }
> > +
> > + /* Mapping PCI BAR regions */
> > + err = pcim_iomap_regions(pdev, BIT(pdata->rg_bar), pci_name(pdev));
> > + if (err) {
> > + pci_err(pdev, "xData BAR I/O remapping failed\n");
> > + return err;
> > + }
> > +
> > + pci_set_master(pdev);
> > +
> > + /* Allocate memory */
> > + dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
> > + if (!dw)
> > + return -ENOMEM;
> > +
> > + /* Data structure initialization */
> > + dw->rg_region.vaddr = pcim_iomap_table(pdev)[pdata->rg_bar];
> > + if (!dw->rg_region.vaddr)
> > + return -ENOMEM;
> > +
> > + dw->rg_region.vaddr += pdata->rg_off;
> > + dw->rg_region.paddr = pdev->resource[pdata->rg_bar].start;
> > + dw->rg_region.paddr += pdata->rg_off;
> > + dw->rg_region.sz = pdata->rg_sz;
> > +
> > + dw->max_wr_len = pcie_get_mps(pdev);
> > + dw->max_wr_len >>= 2;
> > +
> > + dw->max_rd_len = pcie_get_readrq(pdev);
> > + dw->max_rd_len >>= 2;
> > +
> > + SET(dw, RAM_addr, 0x0);
> > + SET(dw, RAM_port, 0x0);
> > +
> > + addr = dw->rg_region.paddr + DW_XDATA_EP_MEM_OFFSET;
> > +#ifdef CONFIG_64BIT
> > + SET_64(dw, addr.reg, addr);
> > +#else /* CONFIG_64BIT */
> > + SET(dw, addr.lsb, lower_32_bits(addr));
> > + SET(dw, addr.msb, upper_32_bits(addr));
> > +#endif /* CONFIG_64BIT */
> > + pci_info(pdev, "xData: target address = 0x%.16llx\n", addr);
> > +
> > + pci_info(pdev, "xData: wr_len=%zu, rd_len=%zu\n",
> > + dw->max_wr_len * 4, dw->max_rd_len * 4);
>
> Drivers need to be quiet...
>
> thanks,
>
> greg k-h
-Gustavo
