Hi everyone I'm trying to get a mainline kernel to run on my Turris Omnia, and am having some trouble getting the PCI bus to work correctly. Specifically, I'm running a 5.10-rc1 kernel (torvalds/master as of this moment), with the resource request fix[0] applied on top. The kernel boots fine, and the patch in [0] makes the PCI devices show up. But I'm still getting initialisation errors like these: [ 1.632709] pci 0000:01:00.0: BAR 0: error updating (0xe0000004 != 0xffffffff) [ 1.632714] pci 0000:01:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff) [ 1.632745] pci 0000:02:00.0: BAR 0: error updating (0xe0200004 != 0xffffffff) [ 1.632750] pci 0000:02:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff) and the WiFi drivers fail to initialise with what appears to me to be errors related to the bus rather than to the drivers themselves: [ 3.509878] ath: phy0: Mac Chip Rev 0xfffc0.f is not supported by this driver [ 3.517049] ath: phy0: Unable to initialize hardware; initialization status: -95 [ 3.524473] ath9k 0000:01:00.0: Failed to initialize device [ 3.530081] ath9k: probe of 0000:01:00.0 failed with error -95 [ 3.536012] ath10k_pci 0000:02:00.0: of_irq_parse_pci: failed with rc=134 [ 3.543049] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 3.548735] ath10k_pci 0000:02:00.0: can't change power state from D3hot to D0 (config space inaccessible) [ 3.588592] ath10k_pci 0000:02:00.0: failed to wake up device : -110 [ 3.595098] ath10k_pci: probe of 0000:02:00.0 failed with error -110 lspci looks OK, though: # lspci 00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) 00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) 00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) 01:00.0 Network controller: Qualcomm Atheros AR9287 Wireless Network Adapter (PCI-Express) (rev 01) 02:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter (rev ff) Does anyone have any clue what could be going on here? Is this a bug, or did I miss something in my config or other initialisation? I've tried with both the stock u-boot distributed with the board, and with an upstream u-boot from latest master; doesn't seem to make any different. Any pointers will be greatly appreciated! Thanks, -Toke [0] https://lore.kernel.org/linux-pci/20201023145252.2691779-1-robh@xxxxxxxxxx/ Full dmesg: [ 1.546457] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400 [ 1.546469] pci 0000:00:02.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 1.546615] pci 0000:00:03.0: [11ab:6820] type 01 class 0x060400 [ 1.546627] pci 0000:00:03.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 1.547341] PCI: bus0: Fast back to back transfers disabled [ 1.547349] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.547356] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.547363] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.547444] pci 0000:01:00.0: [168c:002e] type 00 class 0x028000 [ 1.547466] pci 0000:01:00.0: reg 0x10: [mem 0xe8000000-0xe800ffff 64bit] [ 1.547576] pci 0000:01:00.0: supports D1 [ 1.547581] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 1.547692] pci 0000:00:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 1.601932] PCI: bus1: Fast back to back transfers enabled [ 1.601941] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.602039] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000 [ 1.602063] pci 0000:02:00.0: reg 0x10: [mem 0xea000000-0xea1fffff 64bit] [ 1.602096] pci 0000:02:00.0: reg 0x30: [mem 0xea200000-0xea20ffff pref] [ 1.602174] pci 0000:02:00.0: supports D1 D2 [ 1.602273] pci 0000:00:02.0: ASPM: current common clock configuration is inconsistent, reconfiguring [ 1.631918] PCI: bus2: Fast back to back transfers enabled [ 1.631926] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.632623] PCI: bus3: Fast back to back transfers enabled [ 1.632630] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03 [ 1.632663] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff] [ 1.632671] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe04fffff] [ 1.632679] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 1.632687] pci 0000:00:02.0: BAR 6: assigned [mem 0xe0500000-0xe05007ff pref] [ 1.632694] pci 0000:00:03.0: BAR 6: assigned [mem 0xe0600000-0xe06007ff pref] [ 1.632701] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit] [ 1.632709] pci 0000:01:00.0: BAR 0: error updating (0xe0000004 != 0xffffffff) [ 1.632714] pci 0000:01:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff) [ 1.632720] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.632728] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.632737] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe03fffff 64bit] [ 1.632745] pci 0000:02:00.0: BAR 0: error updating (0xe0200004 != 0xffffffff) [ 1.632750] pci 0000:02:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff) [ 1.632757] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0400000-0xe040ffff pref] [ 1.632762] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.632768] pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe04fffff] [ 1.632774] pci 0000:00:03.0: PCI bridge to [bus 03] [ 1.633030] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.691640] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.691756] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.751635] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.769386] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.770240] printk: console [ttyS0] disabled [ 1.790351] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 15625000) is a 16550A [ 3.040783] printk: console [ttyS0] enabled [ 3.065621] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 31, base_baud = 15625000) is a 16550A [ 3.075329] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.082990] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.090499] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.098335] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.107411] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.116657] scsi host0: ahci-mvebu [ 3.120302] scsi host1: ahci-mvebu [ 3.123825] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53 [ 3.131768] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53 [ 3.140560] spi-nor spi0.0: s25fl164k (8192 Kbytes) [ 3.145494] 2 fixed-partitions partitions found on MTD device spi0.0 [ 3.151868] Creating 2 MTD partitions on "spi0.0": [ 3.156671] 0x000000000000-0x000000100000 : "U-Boot" [ 3.171461] 0x000000100000-0x000000800000 : "Rescue system" [ 3.191747] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.199597] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@xxxxxxxxx>. All Rights Reserved. [ 3.209859] libphy: Fixed MDIO Bus: probed [ 3.214141] tun: Universal TUN/TAP device driver, 1.6 [ 3.219584] libphy: orion_mdio_bus: probed [ 3.224542] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 3.450274] libphy: mv88e6xxx SMI: probed [ 3.461815] mvneta f1070000.ethernet eth0: Using hardware mac address d8:58:d7:00:4e:98 [ 3.470606] mvneta f1030000.ethernet eth1: Using hardware mac address d8:58:d7:00:4e:96 [ 3.479356] mvneta f1034000.ethernet eth2: Using hardware mac address d8:58:d7:00:4e:97 [ 3.482630] ata1: SATA link down (SStatus 0 SControl 300) [ 3.487588] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 3.492831] ata2: SATA link down (SStatus 0 SControl 300) [ 3.498496] ath9k 0000:01:00.0: enabling device (0000 -> 0002) [ 3.509878] ath: phy0: Mac Chip Rev 0xfffc0.f is not supported by this driver [ 3.517049] ath: phy0: Unable to initialize hardware; initialization status: -95 [ 3.524473] ath9k 0000:01:00.0: Failed to initialize device [ 3.530081] ath9k: probe of 0000:01:00.0 failed with error -95 [ 3.536012] ath10k_pci 0000:02:00.0: of_irq_parse_pci: failed with rc=134 [ 3.543049] pci 0000:00:02.0: enabling device (0140 -> 0142) [ 3.548735] ath10k_pci 0000:02:00.0: can't change power state from D3hot to D0 (config space inaccessible) [ 3.588592] ath10k_pci 0000:02:00.0: failed to wake up device : -110 [ 3.595098] ath10k_pci: probe of 0000:02:00.0 failed with error -110 [ 3.601529] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.608072] ehci-pci: EHCI PCI platform driver [ 3.612553] ehci-orion: EHCI orion driver [ 3.616675] orion-ehci f1058000.usb: EHCI Host Controller [ 3.622105] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.629733] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000 [ 3.661261] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.667530] hub 1-0:1.0: USB hub found [ 3.671321] hub 1-0:1.0: 1 port detected [ 3.675700] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.681034] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.688599] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.697867] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000 [ 3.703905] hub 2-0:1.0: USB hub found [ 3.707678] hub 2-0:1.0: 1 port detected [ 3.711767] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.717096] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.724621] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.731026] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.739388] hub 3-0:1.0: USB hub found [ 3.743167] hub 3-0:1.0: 1 port detected [ 3.747339] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.752684] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.760230] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.769502] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000 [ 3.775527] hub 4-0:1.0: USB hub found [ 3.779298] hub 4-0:1.0: 1 port detected [ 3.783756] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.789086] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 3.796610] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 3.803012] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.811375] hub 5-0:1.0: USB hub found [ 3.815147] hub 5-0:1.0: 1 port detected [ 3.819312] usbcore: registered new interface driver usb-storage [ 3.826044] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 3.831632] armada38x-rtc f10a3800.rtc: setting system clock to 2020-10-27T15:31:52 UTC (1603812712) [ 3.840905] i2c /dev entries driver [ 3.846565] orion_wdt: Initial timeout 171 sec [ 3.851350] sdhci: Secure Digital Host Controller Interface driver [ 3.857544] sdhci: Copyright(c) Pierre Ossman [ 3.862041] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.868792] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.876106] usbcore: registered new interface driver usbhid [ 3.881715] usbhid: USB HID core driver [ 3.885678] GACT probability on [ 3.888837] Mirror/redirect action on [ 3.892589] Simple TC action Loaded [ 3.893793] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA [ 3.896117] u32 classifier [ 3.906258] Performance counters on [ 3.910113] input device check on [ 3.913812] Actions configured [ 3.917606] NET: Registered protocol family 10 [ 3.922867] Segment Routing with IPv6 [ 3.926605] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.932956] NET: Registered protocol family 17 [ 3.937500] 8021q: 802.1Q VLAN Support v1.8 [ 3.941850] ThumbEE CPU extension supported. [ 3.946133] Registering SWP/SWPB emulation handler [ 3.951024] Loading compiled-in X.509 certificates [ 3.956916] Btrfs loaded, crc32c=crc32c-generic [ 3.961872] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1 [ 4.027817] mmc0: new high speed MMC card at address 0001 [ 4.033650] mmcblk0: mmc0:0001 H8G4a\x92 7.28 GiB [ 4.038323] mmcblk0boot0: mmc0:0001 H8G4a\x92 partition 1 4.00 MiB [ 4.044421] mmcblk0boot1: mmc0:0001 H8G4a\x92 partition 2 4.00 MiB [ 4.050457] mmcblk0rpmb: mmc0:0001 H8G4a\x92 partition 3 4.00 MiB, chardev (250:0) [ 4.059708] mmcblk0: p1 [ 4.081276] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 4.169488] libphy: mv88e6xxx SMI: probed [ 4.261911] usb-storage 2-1:1.0: USB Mass Storage device detected [ 4.268229] scsi host2: usb-storage 2-1:1.0 [ 4.816096] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=70) [ 4.842702] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=71) [ 4.869246] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=72) [ 4.895772] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=73) [ 4.920733] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=74) [ 4.939701] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode [ 4.950089] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off [ 4.958047] DSA: tree 0 setup [ 4.961339] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.970623] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.977231] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.985879] cfg80211: failed to load regulatory.db [ 4.990987] Waiting 2 sec before mounting root device... [ 5.351539] scsi 2:0:0:0: Direct-Access General UDisk 5.00 PQ: 0 ANSI: 2 [ 5.360060] sd 2:0:0:0: [sda] 7987200 512-byte logical blocks: (4.09 GB/3.81 GiB) [ 5.367691] sd 2:0:0:0: [sda] Write Protect is off [ 5.372503] sd 2:0:0:0: [sda] Mode Sense: 0b 00 00 08 [ 5.372605] sd 2:0:0:0: [sda] No Caching mode page found [ 5.377931] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 5.435076] sda: sda1 [ 5.438130] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 7.047873] BTRFS: device fsid 448334b8-1b27-4738-8118-9e70b56b1e58 devid 1 transid 680 /dev/root scanned by swapper/0 (1) [ 7.059562] BTRFS info (device mmcblk0p1): disk space caching is enabled [ 7.066294] BTRFS info (device mmcblk0p1): has skinny extents [ 7.078585] BTRFS info (device mmcblk0p1): enabling ssd optimizations [ 7.087624] VFS: Mounted root (btrfs filesystem) on device 0:12. [ 7.094044] devtmpfs: mounted [ 7.097581] Freeing unused kernel memory: 1024K [ 7.131431] Run /sbin/init as init process [ 7.135536] with arguments: [ 7.135539] /sbin/init [ 7.135541] earlyprintk [ 7.135543] with environment: [ 7.135545] HOME=/ [ 7.135548] TERM=linux [ 7.220335] random: fast init done [ 7.650974] systemd[1]: systemd 246.6-1.1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [ 7.674141] systemd[1]: Detected architecture arm. [ 7.752534] systemd[1]: Set hostname to <omnia-arch>. [ 7.938493] systemd[164]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1. [ 8.148416] systemd[1]: Queued start job for default target Graphical Interface. [ 8.156570] random: systemd: uninitialized urandom read (16 bytes read) [ 8.164923] systemd[1]: Created slice system-getty.slice. [ 8.201373] random: systemd: uninitialized urandom read (16 bytes read) [ 8.208682] systemd[1]: Created slice system-modprobe.slice. [ 8.241347] random: systemd: uninitialized urandom read (16 bytes read) [ 8.248610] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 8.281970] systemd[1]: Created slice User and Session Slice. [ 8.321507] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 8.371436] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 8.421373] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 8.433099] systemd[1]: Reached target Local Encrypted Volumes. [ 8.481453] systemd[1]: Reached target Paths. [ 8.521358] systemd[1]: Reached target Remote File Systems. [ 8.571330] systemd[1]: Reached target Slices. [ 8.611374] systemd[1]: Reached target Swap. [ 8.641568] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 8.693521] systemd[1]: Listening on Process Core Dump Socket. [ 8.745061] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 8.759882] systemd[1]: Listening on Journal Socket (/dev/log). [ 8.801664] systemd[1]: Listening on Journal Socket. [ 8.848051] systemd[1]: Listening on Network Service Netlink Socket. [ 8.892567] systemd[1]: Listening on udev Control Socket. [ 8.941553] systemd[1]: Listening on udev Kernel Socket. [ 8.981628] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 8.990034] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 8.999279] systemd[1]: Condition check resulted in Kernel Debug File System being skipped. [ 9.010575] systemd[1]: Mounting Kernel Trace File System... [ 9.043918] systemd[1]: Mounting Temporary Directory (/tmp)... [ 9.081515] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. [ 9.095686] systemd[1]: Starting Load Kernel Module drm... [ 9.138063] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 9.148885] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. [ 9.157149] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 9.165757] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. [ 9.177585] systemd[1]: Starting Remount Root and Kernel File Systems... [ 9.211505] systemd[1]: Condition check resulted in Repartition Root Disk being skipped. [ 9.222607] systemd[1]: Starting Apply Kernel Variables... [ 9.264359] systemd[1]: Starting Coldplug All udev Devices... [ 9.305343] systemd[1]: Mounted Kernel Trace File System. [ 9.352014] systemd[1]: Mounted Temporary Directory (/tmp). [ 9.391997] systemd[1]: modprobe@drm.service: Succeeded. [ 9.398342] systemd[1]: Finished Load Kernel Module drm. [ 9.436436] systemd[1]: Finished Remount Root and Kernel File Systems. [ 9.472894] systemd[1]: Finished Apply Kernel Variables. [ 9.514310] systemd[1]: Condition check resulted in First Boot Wizard being skipped. [ 9.529349] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 9.540514] systemd[1]: Starting Load/Save Random Seed... [ 9.561757] systemd[1]: Condition check resulted in Create System Users being skipped. [ 9.578340] systemd[1]: Starting Create Static Device Nodes in /dev... [ 9.639784] systemd[1]: Finished Create Static Device Nodes in /dev. [ 9.692025] systemd[1]: Reached target Local File Systems (Pre). [ 9.741485] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped. [ 9.752637] systemd[1]: Reached target Local File Systems. [ 9.794672] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm. [ 9.831672] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped. [ 9.844130] systemd[1]: Starting Journal Service... [ 9.861510] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped. [ 9.885260] systemd[1]: Starting Rule-based Manager for Device Events and Files... [ 9.932999] systemd[1]: Finished Coldplug All udev Devices. [ 10.175983] systemd[1]: Started Journal Service. [ 11.579842] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii link mode [ 11.607754] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 11.787479] mvneta f1034000.ethernet eth2: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL) [ 11.817734] mvneta f1034000.ethernet eth2: configuring for phy/sgmii link mode [ 12.102369] BTRFS info (device mmcblk0p1): devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by systemd-udevd (194) [ 13.131291] random: crng init done [ 13.134710] random: 7 urandom warning(s) missed due to ratelimiting [ 14.961639] mvneta f1034000.ethernet eth2: Link is Up - 1Gbps/Full - flow control rx/tx [ 14.969684] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
