Hello,
i wish to report a strange issue that my machine experiences with a
NEC USB 3.0 PCI-Express (x1 slot) controller. Normally the controller uses the xhci (usb3) kernel driver.
Now the machine is running
Linux xxxx 2.6.35.4 #2 SMP Wed Sep 1 10:15:04 UTC 2010 x86_64 GNU/Linux
Note that this issue was present in 2.6.34 and 2.6.33 but i though that
it might get fixed in the meantime.
The issue
----------
The controller is sometimes detected and some times not. I mean that at some boots it
is present as a PCI device (listed in pci -v as
05:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) (prog-if 30)
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at febfe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150] #18
Kernel driver in use: xhci_hcd
)
and some other times it just does not exist.
Maybe it is PCIe express related. Also people on linux-usb mailing list suggested this.
I include 2 full dmesg logs ziped due to the size as well a unified diff of them.
NOTE that "echo 1> /sys/bus/pci/rescan" does not do anything.
Please cc the replies if any to the sender email (noxelia ...)
dmesg diff-------------
--- dmesg-xhci-ok-2.6.35.4.log 2010-09-13 12:57:40.000000000 +0000
+++ dmesg.noxhci.2.6.35.4.log 2010-09-13 12:35:07.000000000 +0000
@@ -1,5 +1,5 @@
Linux version 2.6.35.4 (root@zeus) (gcc version 4.4.5 20100728
(prerelease) (Debian 4.4.4-8) ) #2 SMP Wed Sep 1 10:15:04 UTC 2010
-Command line: BOOT_IMAGE=Lx-2.6.354x64_R ro root=801 log_buf_len=3M,
resume=UUID=0000000000000000000000003c0859ca:0x53260628
+Command line: auto BOOT_IMAGE=Lx-2.6.354x64_R ro root=801
log_buf_len=3M, resume=UUID=0000000000000000000000003c0859ca:0x53260628
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
@@ -122,7 +122,7 @@
pcpu-alloc: s82816 r8192 d23680 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
1030879
-Kernel command line: BOOT_IMAGE=Lx-2.6.354x64_R ro root=801
log_buf_len=3M, resume=UUID=0000000000000000000000003c0859ca:0x53260628
+Kernel command line: auto BOOT_IMAGE=Lx-2.6.354x64_R ro root=801
log_buf_len=3M, resume=UUID=0000000000000000000000003c0859ca:0x53260628
log_buf_len: 4194304
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
@@ -143,8 +143,8 @@
#3 [00000ff790 - 0000100000] BIOS reserved
#4 [00000ff780 - 00000ff790] MP-table mpf
#5 [000009fc00 - 00000fdde0] BIOS reserved
- #6 [00000fdf38 - 00000ff780] BIOS reserved
- #7 [00000fdde0 - 00000fdf38] MP-table mpc
+ #6 [00000fdf30 - 00000ff780] BIOS reserved
+ #7 [00000fdde0 - 00000fdf30] MP-table mpc
#8 [0000010000 - 0000012000] TRAMPOLINE
#9 [0000012000 - 0000016000] ACPI WAKEUP
#10 [0000016000 - 0000018000] PGTABLE
@@ -174,8 +174,8 @@
#34 [0001607b80 - 0001607be8] BOOTMEM
#35 [00015e7fc0 - 00015e7fe0] BOOTMEM
#36 [0001607c00 - 0001607c20] BOOTMEM
- #37 [0001607c40 - 0001607caf] BOOTMEM
- #38 [0001607cc0 - 0001607d2f] BOOTMEM
+ #37 [0001607c40 - 0001607cb4] BOOTMEM
+ #38 [0001607cc0 - 0001607d34] BOOTMEM
#39 [0001800000 - 000181c000] BOOTMEM
#40 [0001880000 - 000189c000] BOOTMEM
#41 [0001900000 - 000191c000] BOOTMEM
@@ -207,8 +207,8 @@
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
-Detected 2300.350 MHz processor.
-Calibrating delay loop (skipped), value calculated using timer
frequency.. 4600.69 BogoMIPS (lpj=2300347)
+Detected 2300.118 MHz processor.
+Calibrating delay loop (skipped), value calculated using timer
frequency.. 4600.23 BogoMIPS (lpj=2300115)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 256
@@ -234,7 +234,7 @@
Switch to broadcast mode on CPU1
#2
Brought up 3 CPUs
-Total of 3 processors activated (13800.71 BogoMIPS).
+Total of 3 processors activated (13800.31 BogoMIPS).
Switch to broadcast mode on CPU2
Switch to broadcast mode on CPU0
NET: Registered protocol family 16
@@ -344,22 +344,19 @@
pci 0000:03:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:03:00.0: reg 1c: [mem 0xfa000000-0xfbffffff 64bit]
pci 0000:03:00.0: reg 24: [io 0xec00-0xec7f]
-pci 0000:03:00.0: reg 30: [mem 0xfea80000-0xfeafffff pref]
+pci 0000:03:00.0: reg 30: [mem 0xfeb80000-0xfebfffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0xe000-0xefff]
-pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfeafffff]
+pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfebfffff]
pci 0000:00:10.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:12.0: PCI bridge to [bus 04-04]
pci 0000:00:12.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:12.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
-pci 0000:00:12.0: bridge window [mem 0xf8e00000-0xf8efffff 64bit pref]
-pci 0000:05:00.0: reg 10: [mem 0xfebfe000-0xfebfffff 64bit]
-pci 0000:05:00.0: PME# supported from D0 D3hot
-pci 0000:05:00.0: PME# disabled
+pci 0000:00:12.0: bridge window [mem 0xf8d00000-0xf8dfffff 64bit pref]
pci 0000:00:13.0: PCI bridge to [bus 05-05]
pci 0000:00:13.0: bridge window [io 0xf000-0x0000] (disabled)
-pci 0000:00:13.0: bridge window [mem 0xfeb00000-0xfebfffff]
-pci 0000:00:13.0: bridge window [mem 0xfff00000-0x000fffff pref]
(disabled)
+pci 0000:00:13.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
+pci 0000:00:13.0: bridge window [mem 0xf8e00000-0xf8efffff 64bit pref]
pci 0000:00:14.0: PCI bridge to [bus 06-06]
pci 0000:00:14.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:14.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
@@ -474,16 +471,16 @@
pci 0000:00:08.0: bridge window [mem 0xcdf00000-0xcfffffff pref]
pci 0000:00:10.0: PCI bridge to [bus 03-03]
pci 0000:00:10.0: bridge window [io 0xe000-0xefff]
-pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfeafffff]
+pci 0000:00:10.0: bridge window [mem 0xfa000000-0xfebfffff]
pci 0000:00:10.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:12.0: PCI bridge to [bus 04-04]
pci 0000:00:12.0: bridge window [io disabled]
pci 0000:00:12.0: bridge window [mem disabled]
-pci 0000:00:12.0: bridge window [mem 0xf8e00000-0xf8efffff 64bit pref]
+pci 0000:00:12.0: bridge window [mem 0xf8d00000-0xf8dfffff 64bit pref]
pci 0000:00:13.0: PCI bridge to [bus 05-05]
pci 0000:00:13.0: bridge window [io disabled]
-pci 0000:00:13.0: bridge window [mem 0xfeb00000-0xfebfffff]
-pci 0000:00:13.0: bridge window [mem pref disabled]
+pci 0000:00:13.0: bridge window [mem disabled]
+pci 0000:00:13.0: bridge window [mem 0xf8e00000-0xf8efffff 64bit pref]
pci 0000:00:14.0: PCI bridge to [bus 06-06]
pci 0000:00:14.0: bridge window [io disabled]
pci 0000:00:14.0: bridge window [mem disabled]
@@ -523,10 +520,10 @@
pci_bus 0000:02: resource 2 [mem 0xc8000000-0xcbffffff pref]
pci_bus 0000:02: resource 3 [mem 0xf0000000-0xf3ffffff]
pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
-pci_bus 0000:03: resource 1 [mem 0xfa000000-0xfeafffff]
+pci_bus 0000:03: resource 1 [mem 0xfa000000-0xfebfffff]
pci_bus 0000:03: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
-pci_bus 0000:04: resource 2 [mem 0xf8e00000-0xf8efffff 64bit pref]
-pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff]
+pci_bus 0000:04: resource 2 [mem 0xf8d00000-0xf8dfffff 64bit pref]
+pci_bus 0000:05: resource 2 [mem 0xf8e00000-0xf8efffff 64bit pref]
pci_bus 0000:06: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
@@ -548,7 +545,7 @@
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
audit: initializing netlink socket (disabled)
-type=2000 audit(1284381726.331:1): initialized
+type=2000 audit(1284380968.330:1): initialized
msgmni has been set to 7913
alg: No test for lzf (lzf-generic)
alg: No test for stdrng (krng)
@@ -606,25 +603,24 @@
Initializing XFRM netlink socket
TuxOnIce 3.1.1.1 (http://tuxonice.net)
input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
-ata3: SATA link down (SStatus 0 SControl 300)
-ata6: SATA link down (SStatus 0 SControl 300)
-ata5: SATA link down (SStatus 0 SControl 300)
-ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
+ata3: SATA link down (SStatus 0 SControl 300)
ata2.00: ATAPI: TSSTcorp CDDVDW SH-S223F, SB00, max UDMA/100
+ata5: SATA link down (SStatus 0 SControl 300)
+ata6: SATA link down (SStatus 0 SControl 300)
+ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD10EADS-00L5B1, 01.01A01, max UDMA/133
-ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/100
+ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-00L 01.0 PQ: 0
ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
-sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
- sda:
scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223F SB00 PQ: 0
ANSI: 5
- sda1 sda2 sda3 sda4
+sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
+ sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
TuxOnIce: Can't translate "UUID=0000000000000000000000003c0859ca" into
a device id yet.
EXT3-fs: barriers not enabled
@@ -633,51 +629,43 @@
VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
Freeing unused kernel memory: 472k freed
input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
+ACPI: acpi_idle registered with cpuidle
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
-EDAC MC: Ver: 2.1.0 Sep 1 2010
-EDAC amd64_edac: Ver: 3.3.0 Sep 1 2010
-EDAC amd64: This node reports that Memory ECC is currently disabled,
set F3x44[22] (0000:00:18.3).
-EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will
not load.
- Either enable ECC checking or force module loading by setting
'ecc_enable_override'.
- (Note that use of the override may cause unknown side effects.)
-amd64_edac: probe of 0000:00:18.2 failed with error -22
+ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
+ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low)
-> IRQ 22
+ehci_hcd 0000:00:02.1: setting latency timer to 64
+ehci_hcd 0000:00:02.1: EHCI Host Controller
+ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
+ehci_hcd 0000:00:02.1: debug port 1
+ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
+ehci_hcd 0000:00:02.1: irq 22, io mem 0xf967ec00
+ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 6 ports detected
+ACPI: PCI Interrupt Link [UB12] enabled at IRQ 21
+input: PC Speaker as /devices/platform/pcspkr/input/input3
+ehci_hcd 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 21 (level, low)
-> IRQ 21
+ehci_hcd 0000:00:04.1: setting latency timer to 64
+ehci_hcd 0000:00:04.1: EHCI Host Controller
+ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
+ehci_hcd 0000:00:04.1: debug port 1
+ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
+ehci_hcd 0000:00:04.1: irq 21, io mem 0xf967e800
+ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
+hub 2-0:1.0: USB hub found
+ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
-rtc_cmos 00:06: RTC can wake from S4
-rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
-rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
+hub 2-0:1.0: 6 ports detected
amd74xx 0000:00:06.0: UDMA133 controller
amd74xx 0000:00:06.0: IDE controller (0x10de:0x0759 rev 0xa1)
amd74xx 0000:00:06.0: IDE port disabled
amd74xx 0000:00:06.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7
Probing IDE interface ide0...
-input: PC Speaker as /devices/platform/pcspkr/input/input3
-00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
-ACPI: acpi_idle registered with cpuidle
-ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
-ohci1394 0000:01:08.0: PCI INT A -> Link[LNKA] -> GSI 18 (level, low)
-> IRQ 18
-sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
-Uniform CD-ROM driver Revision: 3.20
-sr 1:0:0:0: Attached scsi CD-ROM sr0
-ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
-ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]
MMIO=[f97ff800-f97fffff] Max Packet=[2048] IR/IT contexts=[4/8]
-sd 0:0:0:0: Attached scsi generic sg0 type 0
-sr 1:0:0:0: Attached scsi generic sg1 type 5
-ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
-xhci_hcd 0000:05:00.0: PCI INT A -> Link[LN3A] -> GSI 16 (level, low)
-> IRQ 16
-xhci_hcd 0000:05:00.0: setting latency timer to 64
-xhci_hcd 0000:05:00.0: xHCI Host Controller
-xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 1
-xhci_hcd 0000:05:00.0: irq 16, io mem 0xfebfe000
-IR NEC protocol handler initialized
-usb usb1: No SuperSpeed endpoint companion for config 1 interface 0
altsetting 0 ep 129: using minimum values
-xHCI xhci_add_endpoint called for root hub
-xHCI xhci_check_bandwidth called for root hub
-hub 1-0:1.0: USB hub found
-hub 1-0:1.0: 4 ports detected
yenta_cardbus 0000:01:09.0: CardBus bridge found [14ef:0101]
yenta_cardbus 0000:01:09.0: ISA IRQ mask 0x0000, PCI irq 19
yenta_cardbus 0000:01:09.0: Socket status: 30000006
@@ -687,8 +675,58 @@
pcmcia_socket pcmcia_socket0: cs: memory probe 0xf9700000-0xf9ffffff:
excluding 0xf9790000-0xf981ffff
yenta_cardbus 0000:01:09.0: pcmcia: parent PCI bridge window: [mem
0xcdf00000-0xcfffffff pref]
pcmcia_socket pcmcia_socket0: cs: memory probe 0xcdf00000-0xcfffffff:
excluding 0xcdf00000-0xcfffffff
+EDAC MC: Ver: 2.1.0 Sep 1 2010
+EDAC amd64_edac: Ver: 3.3.0 Sep 1 2010
+ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
+ohci1394 0000:01:08.0: PCI INT A -> Link[LNKA] -> GSI 18 (level, low)
-> IRQ 18
+IR NEC protocol handler initialized
+ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]
MMIO=[f97ff800-f97fffff] Max Packet=[2048] IR/IT contexts=[4/8]
+IR RC5(x) protocol handler initialized
+IR RC6 protocol handler initialized
+rtc_cmos 00:06: RTC can wake from S4
+rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
+rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
+sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
+00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
+Uniform CD-ROM driver Revision: 3.20
+sr 1:0:0:0: Attached scsi CD-ROM sr0
+IR JVC protocol handler initialized
+sd 0:0:0:0: Attached scsi generic sg0 type 0
+sr 1:0:0:0: Attached scsi generic sg1 type 5
+ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
+ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 20
+ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 20 (level, low)
-> IRQ 20
+ohci_hcd 0000:00:02.0: setting latency timer to 64
+ohci_hcd 0000:00:02.0: OHCI Host Controller
+ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
+ohci_hcd 0000:00:02.0: irq 20, io mem 0xf967f000
+hub 3-0:1.0: USB hub found
+hub 3-0:1.0: 6 ports detected
+ACPI: PCI Interrupt Link [UB11] enabled at IRQ 23
+ohci_hcd 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 23 (level, low)
-> IRQ 23
+ohci_hcd 0000:00:04.0: setting latency timer to 64
+ohci_hcd 0000:00:04.0: OHCI Host Controller
+ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
+ohci_hcd 0000:00:04.0: irq 23, io mem 0xf967d000
+IR Sony protocol handler initialized
+hub 4-0:1.0: USB hub found
+hub 4-0:1.0: 6 ports detected
+forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
+ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
+forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 22 (level, low)
-> IRQ 22
+forcedeth 0000:00:0a.0: setting latency timer to 64
+forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr
00:19:66:8c:ae:37
+forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3
+i2c i2c-0: nForce2 SMBus adapter at 0x2d00
Linux video capture interface: v2.00
-usb 1-4: new high speed USB device using xhci_hcd and address 0
+ACPI: resource nForce2_smbus [io 0x2e00-0x2e3f] conflicts with ACPI
region SM00 [mem 0x00002e00-0x00002e3f 64bit pref disabled]
+ACPI: If an ACPI driver is available for this device, you should use it
instead of the native driver
+EDAC amd64: This node reports that Memory ECC is currently disabled,
set F3x44[22] (0000:00:18.3).
+EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will
not load.
+ Either enable ECC checking or force module loading by setting
'ecc_enable_override'.
+ (Note that use of the override may cause unknown side effects.)
+amd64_edac: probe of 0000:00:18.2 failed with error -22
+usb 3-3: new low speed USB device using ohci_hcd and address 2
bttv: driver version 0.9.18 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
@@ -697,90 +735,28 @@
bttv0: Bt878 (rev 17) at 0000:01:0a.0, irq: 17, latency: 32, mmio:
0xcdfff000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID
is 107d:6606
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,autodetected]
-ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
-forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
-ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
-forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 22 (level, low)
-> IRQ 22
-forcedeth 0000:00:0a.0: setting latency timer to 64
bttv0: gpio: en=00000000, out=00000000 in=00bff706 [init]
bttv0: tuner type=5
-IR RC5(x) protocol handler initialized
-forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr
00:19:66:8c:ae:37
-forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3
-i2c i2c-1: nForce2 SMBus adapter at 0x2d00
-xhci_hcd 0000:05:00.0: WARN: short transfer on control ep
-ACPI: resource nForce2_smbus [io 0x2e00-0x2e3f] conflicts with ACPI
region SM00 [mem 0x00002e00-0x00002e3f 64bit disabled]
-ACPI: If an ACPI driver is available for this device, you should use it
instead of the native driver
-ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21
-ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 21 (level, low)
-> IRQ 21
-ehci_hcd 0000:00:02.1: setting latency timer to 64
-ehci_hcd 0000:00:02.1: EHCI Host Controller
-ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
-ehci_hcd 0000:00:02.1: debug port 1
-ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
-ehci_hcd 0000:00:02.1: irq 21, io mem 0xf967ec00
-ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
-hub 2-0:1.0: USB hub found
-hub 2-0:1.0: 6 ports detected
-ACPI: PCI Interrupt Link [UB12] enabled at IRQ 20
-ehci_hcd 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 20 (level, low)
-> IRQ 20
-ehci_hcd 0000:00:04.1: setting latency timer to 64
-ehci_hcd 0000:00:04.1: EHCI Host Controller
-ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 3
-ehci_hcd 0000:00:04.1: debug port 1
-ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
-ehci_hcd 0000:00:04.1: irq 20, io mem 0xf967e800
-ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
-hub 3-0:1.0: USB hub found
-hub 3-0:1.0: 6 ports detected
-ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
-ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low)
-> IRQ 23
-ohci_hcd 0000:00:02.0: setting latency timer to 64
-ohci_hcd 0000:00:02.0: OHCI Host Controller
-ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 4
-xhci_hcd 0000:05:00.0: WARN: short transfer on control ep
-ohci_hcd 0000:00:02.0: irq 23, io mem 0xf967f000
-IR RC6 protocol handler initialized
-xhci_hcd 0000:05:00.0: WARN: short transfer on control ep
-hub 4-0:1.0: USB hub found
-hub 4-0:1.0: 6 ports detected
-ACPI: PCI Interrupt Link [UB11] enabled at IRQ 22
-ohci_hcd 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 22 (level, low)
-> IRQ 22
-ohci_hcd 0000:00:04.0: setting latency timer to 64
-ohci_hcd 0000:00:04.0: OHCI Host Controller
-ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 5
-ohci_hcd 0000:00:04.0: irq 22, io mem 0xf967d000
-cfg80211: Calling CRDA to update world regulatory domain
-hub 5-0:1.0: USB hub found
-hub 5-0:1.0: 6 ports detected
-IR JVC protocol handler initialized
-IR Sony protocol handler initialized
-bttv0: audio absent, no audio device found!
-tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
-usb 4-3: new low speed USB device using ohci_hcd and address 2
-tuner-simple 0-0061: creating new instance
-tuner-simple 0-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
-bttv0: registered device video0
-bttv0: registered device vbi0
-bttv0: registered device radio0
-bttv0: PLL: 28636363 => 35468950 .. ok
-phy0: Selected rate control algorithm 'pid'
-Registered led device: rt73usb-phy0::radio
-Registered led device: rt73usb-phy0::assoc
-Registered led device: rt73usb-phy0::quality
-usbcore: registered new interface driver rt73usb
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
-Registered IR keymap rc-winfast
-input: bttv IR (card=34) as
/devices/pci0000:00/0000:00:08.0/0000:01:0a.0/rc/rc0/input4
-rc0: bttv IR (card=34) as
/devices/pci0000:00/0000:00:08.0/0000:01:0a.0/rc/rc0
-input: HID 062a:0000 as
/devices/pci0000:00/0000:00:02.0/usb4/4-3/4-3:1.0/input/input5
+input: HID 062a:0000 as
/devices/pci0000:00/0000:00:02.0/usb3/3-3/3-3:1.0/input/input4
generic-usb 0003:062A:0000.0001: input: USB HID v1.10 Mouse [HID
062a:0000] on usb-0000:00:02.0-3/input0
-ieee1394: Host added: ID:BUS[0-00:1023] GUID[008f13002ee60500]
+bttv0: audio absent, no audio device found!
+tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
nvidia 0000:03:00.0: PCI INT A -> Link[LN0A] -> GSI 18 (level, low) ->
IRQ 18
nvidia 0000:03:00.0: setting latency timer to 64
vgaarb: device changed decodes:
PCI:0000:03:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 256.44 Thu Jul 29
01:22:44 PDT 2010
+tuner-simple 1-0061: creating new instance
+tuner-simple 1-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
+bttv0: registered device video0
+bttv0: registered device vbi0
+bttv0: registered device radio0
+bttv0: PLL: 28636363 => 35468950 .. ok
+ieee1394: Host added: ID:BUS[0-00:1023] GUID[008f13002ee60500]
+Registered IR keymap rc-winfast
+input: bttv IR (card=34) as
/devices/pci0000:00/0000:00:08.0/0000:01:0a.0/rc/rc0/input5
+rc0: bttv IR (card=34) as
/devices/pci0000:00/0000:00:08.0/0000:01:0a.0/rc/rc0
HDA Intel 0000:00:07.0: power state changed by ACPI to D0
HDA Intel 0000:00:07.0: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
@@ -808,29 +784,29 @@
powernow-k8: Found 1 AMD Phenom(tm) 8650 Triple-Core Processor (3 cpu
cores) (version 2.20.00)
powernow-k8: 0 : pstate 0 (2300 MHz)
powernow-k8: 1 : pstate 1 (1150 MHz)
........
<<attachment: dmesg-xhci.zip>>
