On 07/19/2010 09:19 PM, Robert Hancock wrote: > On Mon, Jul 19, 2010 at 10:29 AM, Jiri Slaby <jslaby@xxxxxxx> wrote: >>>> I still no point in comparing this to Windows' setup. We can't find out >>>> whether it is quirked or better (without some bug) handled there. >>> >>> Well, you can see if Windows shows IRQ 10 or 11 for that device.. >> >> But how can I find out which link it is routed to in Windows? Without >> that information the number is meaningless, no? > > If you look at the pattern of which IRQs are shared by what devices in > Linux and compare it to Windows you can get a good idea. Normally the > assignment of devices to interrupt lines is hard-wired on the > motherboard and doesn't change. Ok, thanks for the hint. What we've found out is that it works on 2.6.27 (with slightly changed configuration). In dmesgs, the only two relevant differences I see are the 8250 interrupt sharing and disabled-apic handling. 8250.irqs_share=1 passed to 2.6.32 does not help. The apic, in the new kernel, returns zeros on read, whereas on the old one, there is a dummy page which returns previously stored values if I understand correctly. Can this have an effect? The diff between .configs is at: http://www.fi.muni.cz/~xslaby/sklad/conf-diff Initializing cgroup subsys cpuset Initializing cgroup subsys cpu -Linux version 2.6.27.19-5-default (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2009-02-28 04:40:21 +0100 +Linux version 2.6.32.10-0.4-default (geeko@buildhost) (gcc version 4.3.4 [gcc-4_3-branch revision 152973] (SUSE Linux) ) #1 SMP 2010-03-29 11:58:05 +0200 +KERNEL supported cpus: + Intel GenuineIntel + AMD AuthenticAMD + NSC Geode by NSC + Cyrix CyrixInstead + Centaur CentaurHauls + Transmeta GenuineTMx86 + Transmeta TransmetaCPU + UMC UMC UMC UMC BIOS-provided physical RAM map: - BIOS-e820: 0000000000000000 - 000000000009f000 (usable) - BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) + BIOS-e820: 0000000000000000 - 000000000009f800 (usable) + BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved) BIOS-e820: 00000000000e5800 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fbf0000 (usable) @@ -12,81 +21,128 @@ BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved) DMI 2.3 present. last_pfn = 0x1fbf0 max_arch_pfn = 0x100000 +MTRR default type: uncachable +MTRR fixed ranges enabled: + 00000-9FFFF write-back + A0000-BFFFF uncachable + C0000-C7FFF write-protect + C8000-DFFFF uncachable + E0000-FFFFF write-protect +MTRR variable ranges enabled: + 0 base 000000000 mask FF0000000 write-back + 1 base 010000000 mask FF8000000 write-back + 2 base 018000000 mask FFC000000 write-back + 3 base 01C000000 mask FFE000000 write-back + 4 base 01E000000 mask FFF000000 write-back + 5 base 01F000000 mask FFF800000 write-back + 6 base 01F800000 mask FFFC00000 write-back + 7 disabled x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 +e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved) +Scanning 1 areas for low memory corruption +modified physical RAM map: + modified: 0000000000000000 - 0000000000002000 (usable) + modified: 0000000000002000 - 0000000000006000 (reserved) + modified: 0000000000006000 - 000000000009f800 (usable) + modified: 000000000009f800 - 00000000000a0000 (reserved) + modified: 00000000000dc000 - 00000000000e0000 (reserved) + modified: 00000000000e5800 - 0000000000100000 (reserved) + modified: 0000000000100000 - 000000001fbf0000 (usable) + modified: 000000001fbf0000 - 000000001fbffc00 (ACPI data) + modified: 000000001fbffc00 - 000000001fc00000 (ACPI NVS) + modified: 00000000fffe0000 - 0000000100000000 (reserved) +initial memory mapped : 0 - 00c00000 +init_memory_mapping: 0000000000000000-000000001fbf0000 + 0000000000 - 0000400000 page 4k + 0000400000 - 001f800000 page 2M + 001f800000 - 001fbf0000 page 4k kernel direct mapping tables up to 1fbf0000 @ 7000-d000 -RAMDISK: 1f627000 - 1fbdfdb3 -ACPI: RSDP 000F7560, 0014 (r0 PTLTD ) -ACPI: RSDT 1FBFDAAC, 002C (r1 PTLTD RSDT 6040000 LTP 0) -ACPI: FACP 1FBFFB64, 0074 (r1 IBM 4810-31x 6040000 PTL 1000000) -ACPI: DSDT 1FBFDAD8, 208C (r1 VIA PTL_ACPI 6040000 MSFT 100000B) -ACPI: FACS 1FBFFFC0, 0040 -ACPI: BOOT 1FBFFBD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) +RAMDISK: 1f68a000 - 1fbdf22e +ACPI: RSDP 000f7560 00014 (v00 PTLTD ) +ACPI: RSDT 1fbfdaac 0002C (v01 PTLTD ? RSDT 06040000 LTP 00000000) +ACPI: FACP 1fbffb64 00074 (v01 IBM 4810-31x 06040000 PTL 01000000) +ACPI: DSDT 1fbfdad8 0208C (v01 VIA PTL_ACPI 06040000 MSFT 0100000B) +ACPI: FACS 1fbfffc0 00040 +ACPI: BOOT 1fbffbd8 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001) 0MB HIGHMEM available. 507MB LOWMEM available. mapped low ram: 0 - 1fbf0000 - low ram: 00000000 - 1fbf0000 - bootmap 00002000 - 00005f80 + low ram: 0 - 1fbf0000 + node 0 low ram: 00000000 - 1fbf0000 + node 0 bootmap 00009000 - 0000cf80 (9 early reservations) ==> bootmem [0000000000 - 001fbf0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] - #3 [0000100000 - 0000634a5c] TEXT DATA BSS ==> [0000100000 - 0000634a5c] - #4 [001f627000 - 001fbdfdb3] RAMDISK ==> [001f627000 - 001fbdfdb3] - #5 [0000635000 - 0000638000] INIT_PG_TABLE ==> [0000635000 - 0000638000] - #6 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000] + #3 [0000200000 - 00008bea84] TEXT DATA BSS ==> [0000200000 - 00008bea84] + #4 [001f68a000 - 001fbdf22e] RAMDISK ==> [001f68a000 - 001fbdf22e] + #5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000] + #6 [00008bf000 - 00008c209a] BRK ==> [00008bf000 - 00008c209a] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000] - #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000] + #8 [0000009000 - 000000d000] BOOTMAP ==> [0000009000 - 000000d000] Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x0001fbf0 HighMem 0x0001fbf0 -> 0x0001fbf0 Movable zone start PFN for each node -early_node_map[2] active PFN ranges - 0: 0x00000000 -> 0x0000009f +early_node_map[3] active PFN ranges + 0: 0x00000000 -> 0x00000002 + 0: 0x00000006 -> 0x0000009f 0: 0x00000100 -> 0x0001fbf0 -On node 0 totalpages: 129935 -free_area_init_node: node 0, pgdat c050a280, node_mem_map c1000000 +On node 0 totalpages: 129931 +free_area_init_node: node 0, pgdat c0769580, node_mem_map c1001000 + DMA zone: 32 pages used for memmap + DMA zone: 0 pages reserved DMA zone: 3963 pages, LIFO batch:0 - Normal zone: 124829 pages, LIFO batch:31 + Normal zone: 984 pages used for memmap + Normal zone: 124952 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x8008 SMP: Allowing 1 CPUs, 0 hotplug CPUs No local APIC present or hardware disabled -mapped APIC to ffffb000 (01479000) +APIC: disable apic facility +nr_irqs_gsi: 16 +PM: Registered nosave memory: 0000000000002000 - 0000000000006000 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000 PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 00000000000e6000 PM: Registered nosave memory: 00000000000e6000 - 0000000000100000 -Allocating PCI resources starting at 20000000 (gap: 1fc00000:e03e0000) -PERCPU: Allocating 37916 bytes of per cpu data -NR_CPUS: 32, nr_cpu_ids: 1, nr_node_ids 1 -Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128792 -Kernel command line: root=/dev/disk/by-id/ata-Maxtor_4D040H2_D23LF17E-part2 resume=/dev/disk/by-id/ata-Maxtor_4D040H2_D23LF17E-part1 splash=silent vga=0x317 +Allocating PCI resources starting at 1fc00000 (gap: 1fc00000:e03e0000) +Booting paravirtualized kernel on bare hardware +NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 +PERCPU: Embedded 12 pages/cpu @c1400000 s28184 r0 d20968 u4194304 +pcpu-alloc: s28184 r0 d20968 u4194304 alloc=1*4194304 +pcpu-alloc: [0] 0 +Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128915 +Kernel command line: root=/dev/disk/by-id/ata-WDC_WD400BB-23JHA1_WD-WMAMA1000905-part3 resume=/dev/disk/by-id/ata-WDC_WD400BB-23JHA1_WD-WMAMA1000905-part2 splash=silent 3 bootsplash: silent mode. +PID hash table entries: 2048 (order: 1, 8192 bytes) +Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) +Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 -PID hash table entries: 2048 (order: 11, 8192 bytes) -TSC: PIT calibration confirmed by PMTIMER. -TSC: using PIT calibration value -Detected 1191.973 MHz processor. -Console: colour dummy device 80x25 -console [tty0] enabled -Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) -Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) -Memory: 503284k/520128k available (2297k kernel code, 16264k reserved, 1925k data, 280k init, 0k highmem) +allocated 2600640 bytes of page_cgroup +please try 'cgroup_disable=memory' option if you don't want memory cgroups +Initializing HighMem for node 0 (00000000:00000000) +Memory: 500028k/520128k available (3228k kernel code, 19492k reserved, 2358k data, 400k init, 0k highmem) virtual kernel memory layout: - fixmap : 0xffdf7000 - 0xfffff000 (2080 kB) + fixmap : 0xffd34000 - 0xfffff000 (2860 kB) pkmap : 0xff400000 - 0xff800000 (4096 kB) - vmalloc : 0xe0800000 - 0xff3fe000 ( 491 MB) + vmalloc : 0xe03f0000 - 0xff3fe000 ( 496 MB) lowmem : 0xc0000000 - 0xdfbf0000 ( 507 MB) - .init : 0xc0527000 - 0xc056d000 ( 280 kB) - .data : 0xc033e4f5 - 0xc051fcd0 (1925 kB) - .text : 0xc0100000 - 0xc033e4f5 (2297 kB) + .init : 0xc0775000 - 0xc07d9000 ( 400 kB) + .data : 0xc0527319 - 0xc0774ee8 (2358 kB) + .text : 0xc0200000 - 0xc0527319 (3228 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. -CPA: page pool initialized 1 of 1 pages preallocated -Calibrating delay loop (skipped), value calculated using timer frequency.. 2383.94 BogoMIPS (lpj=4767892) +Hierarchical RCU implementation. +NR_IRQS:2304 nr_irqs:256 +Console: colour VGA+ 80x25 +console [tty0] enabled +Fast TSC calibration using PIT +Detected 1191.909 MHz processor. +Calibrating delay loop (skipped), value calculated using timer frequency.. 2383.81 BogoMIPS (lpj=4767636) kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved Security Framework initialized AppArmor: AppArmor initialized @@ -96,108 +152,102 @@ Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer -CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) -CPU: L2 Cache: 64K (32 bytes/line) +Initializing cgroup subsys net_cls +Performance Events: Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code -Freeing SMP alternatives: 18k freed -ACPI: Core revision 20080609 -ACPI: Checking initramfs for custom DSDT -Parsing all Control Methods: -Table [DSDT](id 0001) - 259 Objects with 34 Devices 66 Methods 12 Regions - tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired +Freeing SMP alternatives: 14k freed +ACPI: Core revision 20090903 ACPI: setting ELCR to 0200 (from 0e00) -evxfevnt-0091 [00] enable : Transition to ACPI mode successful -weird, boot CPU (#0) not listedby the BIOS. +Enabling APIC mode: Flat. Using 0 I/O APICs +weird, boot CPU (#0) not listed by the BIOS. SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. SMP disabled Brought up 1 CPUs -Total of 1 processors activated (2383.94 BogoMIPS). -CPU0 attaching NULL sched-domain. -net_namespace: 1044 bytes +Total of 1 processors activated (2383.81 BogoMIPS). +devtmpfs: initialized +regulator: core version 0.5 +Time: 21:46:46 Date: 04/13/11 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd7ee, last bus=1 PCI: Using configuration type 1 for base access -perfmon: version 2.82 -perfmon: CPU hotplug support enabled -evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9 +bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT -Completing Region/Field/Buffer/Package initialization:................................................ -Initialized 10/12 Regions 3/4 Fields 22/23 Buffers 13/13 Packages (268 nodes) -Initializing Device/Processor/Thermal objects by executing _INI methods: -Executed 0 _INI methods requiring 0 _STA executions (examined 37 objects) -evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 0 Runtime GPEs in this block ACPI: Interpreter enabled ACPI: (supports S0 S1 S5) ACPI: Using PIC for interrupt routing +ACPI: No dock devices found. +PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug ACPI: PCI Root Bridge [PCI0] (0000:00) -PCI: 0000:00:00.0 reg 10 32bit mmio: [fd000000, fdffffff] -PCI: 0000:00:07.1 reg 20 io port: [1840, 184f] -PCI: 0000:00:07.2 reg 20 io port: [1800, 181f] -PCI: 0000:00:07.3 reg 20 io port: [1820, 183f] +pci 0000:00:00.0: reg 10 32bit mmio pref: [0xfd000000-0xfdffffff] +pci 0000:00:07.1: reg 20 io port: [0x1840-0x184f] +pci 0000:00:07.2: reg 20 io port: [0x1800-0x181f] +pci 0000:00:07.3: reg 20 io port: [0x1820-0x183f] pci 0000:00:07.4: quirk: region 6800-687f claimed by vt82c686 HW-mon pci 0000:00:07.4: quirk: region 8100-810f claimed by vt82c686 SMB -PCI: 0000:00:07.5 reg 10 io port: [1000, 10ff] -PCI: 0000:00:07.5 reg 14 io port: [1874, 1877] -PCI: 0000:00:07.5 reg 18 io port: [1870, 1873] -PCI: 0000:00:09.0 reg 10 io port: [1898, 189f] -PCI: 0000:00:09.0 reg 14 io port: [1890, 1897] -PCI: 0000:00:09.0 reg 18 io port: [1888, 188f] -PCI: 0000:00:09.0 reg 1c io port: [1880, 1887] -PCI: 0000:00:09.0 reg 20 io port: [1878, 187f] -PCI: 0000:00:09.0 reg 24 io port: [1850, 185f] -pci 0000:00:09.0: Netmos 9835 (9 parallel, 9 serial); changing class SERIAL to OTHER (use parport_serial) -PCI: 0000:00:0b.0 reg 10 io port: [18c0, 18c7] -PCI: 0000:00:0b.0 reg 14 io port: [18b8, 18bf] -PCI: 0000:00:0b.0 reg 18 io port: [18b0, 18b7] -PCI: 0000:00:0b.0 reg 1c io port: [18a8, 18af] -PCI: 0000:00:0b.0 reg 20 io port: [18a0, 18a7] -PCI: 0000:00:0b.0 reg 24 io port: [1860, 186f] -PCI: 0000:00:0d.0 reg 10 io port: [1400, 14ff] -PCI: 0000:00:0d.0 reg 14 32bit mmio: [fb000000, fb000fff] -PCI: 0000:00:0d.0 reg 30 32bit mmio: [0, ffff] -pci 0000:00:0d.0: supports D1 -pci 0000:00:0d.0: supports D2 +pci 0000:00:07.5: reg 10 io port: [0x1000-0x10ff] +pci 0000:00:07.5: reg 14 io port: [0x1874-0x1877] +pci 0000:00:07.5: reg 18 io port: [0x1870-0x1873] +pci 0000:00:09.0: reg 10 io port: [0x1898-0x189f] +pci 0000:00:09.0: reg 14 io port: [0x1890-0x1897] +pci 0000:00:09.0: reg 18 io port: [0x1888-0x188f] +pci 0000:00:09.0: reg 1c io port: [0x1880-0x1887] +pci 0000:00:09.0: reg 20 io port: [0x1878-0x187f] +pci 0000:00:09.0: reg 24 io port: [0x1850-0x185f] +pci 0000:00:0b.0: reg 10 io port: [0x18c0-0x18c7] +pci 0000:00:0b.0: reg 14 io port: [0x18b8-0x18bf] +pci 0000:00:0b.0: reg 18 io port: [0x18b0-0x18b7] +pci 0000:00:0b.0: reg 1c io port: [0x18a8-0x18af] +pci 0000:00:0b.0: reg 20 io port: [0x18a0-0x18a7] +pci 0000:00:0b.0: reg 24 io port: [0x1860-0x186f] +pci 0000:00:0d.0: reg 10 io port: [0x1400-0x14ff] +pci 0000:00:0d.0: reg 14 32bit mmio: [0xfb000000-0xfb000fff] +pci 0000:00:0d.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] +pci 0000:00:0d.0: supports D1 D2 pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0d.0: PME# disabled -PCI: 0000:01:00.0 reg 10 32bit mmio: [fc000000, fc7fffff] -PCI: 0000:01:00.0 reg 14 32bit mmio: [fb100000, fb11ffff] -PCI: 0000:01:00.0 reg 18 32bit mmio: [fb800000, fbffffff] -PCI: 0000:01:00.0 reg 30 32bit mmio: [0, ffff] -pci 0000:01:00.0: supports D1 -pci 0000:01:00.0: supports D2 -PCI: bridge 0000:00:01.0 32bit mmio: [fb100000, fc7fffff] -bus 00 -> node 0 +pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfc7fffff] +pci 0000:01:00.0: reg 14 32bit mmio: [0xfb100000-0xfb11ffff] +pci 0000:01:00.0: reg 18 32bit mmio: [0xfb800000-0xfbffffff] +pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] +pci 0000:01:00.0: supports D1 D2 +pci 0000:00:01.0: PCI bridge to [bus 01-01] +pci 0000:00:01.0: bridge 32bit mmio: [0xfb100000-0xfc7fffff] +pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PPB_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 9 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 9 *10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 *9 10 11 12) -Linux Plug and Play Support v0.97 (c) Adam Belay +vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none +vgaarb: loaded +PCI: Using ACPI for IRQ routing +NetLabel: Initializing +NetLabel: domain hash size = 128 +NetLabel: protocols = UNLABELED CIPSOv4 +NetLabel: unlabeled traffic allowed by default +Switching to clocksource tsc +AppArmor: AppArmor Filesystem Enabled pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP -PCI: Using ACPI for IRQ routing -AppArmor: AppArmor Filesystem Enabled system 00:05: iomem range 0x0-0x9ffff could not be reserved system 00:05: iomem range 0xe0000-0xfffff could not be reserved system 00:06: ioport range 0x4d0-0x4d1 has been reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: disabled pci 0000:00:01.0: MEM window: 0xfb100000-0xfc7fffff -pci 0000:00:01.0: PREFETCH window: 0x00000020000000-0x000000200fffff +pci 0000:00:01.0: PREFETCH window: 0x20000000-0x200fffff pci 0000:00:01.0: setting latency timer to 64 -bus: 00 index 0 io port: [0, ffff] -bus: 00 index 1 mmio: [0, ffffffff] -bus: 01 index 0 mmio: [0, 0] -bus: 01 index 1 mmio: [fb100000, fc7fffff] -bus: 01 index 2 mmio: [20000000, 200fffff] -bus: 01 index 3 mmio: [0, 0] +pci_bus 0000:00: resource 0 io: [0x00-0xffff] +pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] +pci_bus 0000:01: resource 1 mem: [0xfb100000-0xfc7fffff] +pci_bus 0000:01: resource 2 pref mem [0x20000000-0x200fffff] NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) @@ -205,39 +255,31 @@ TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 -Unpacking initramfs...<7>Switched to high resolution mode on CPU 0 - done -Freeing initrd memory: 5859k freed +pci 0000:00:01.0: disabling DAC on VIA PCI bridge +pci 0000:00:07.0: Disabling VIA external APIC routing +pci 0000:01:00.0: Boot video device +Unpacking initramfs... +Freeing initrd memory: 5460k freed Simple Boot Flag at 0x36 set to 0x1 +Scanning for low memory corruption every 60 seconds audit: initializing netlink socket (disabled) -type=2000 audit(1311129780.512:1): initialized +type=2000 audit(1302731206.718:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages -VFS: Disk quotas dquot_6.5.1 +VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) -msgmni has been set to 248 -Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) +msgmni has been set to 246 +alg: No test for stdrng (krng) +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) -perfmon: added sampling format default -PCI: VIA PCI bridge detected.Disabling DAC. -pci 0000:00:07.0: Disabling VIA external APIC routing -pci 0000:01:00.0: Boot video device -vesafb: framebuffer at 0xfc000000, mapped to 0xe0880000, using 4096k, total 4096k -vesafb: mode is 1024x768x16, linelength=2048, pages=1 -vesafb: protected mode interface info at c000:67c0 -vesafb: pmi: set display start = c00c67d0, set palette = c00c6833 -vesafb: scrolling: redraw -vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 -bootsplash 3.1.6-2004/03/31: looking for picture... -bootsplash: silentjpeg size 59221 bytes -bootsplash: ...found (1024x768, 31358 bytes, v3). -Console: switching to colour frame buffer device 124x44 -fb0: VESA VGA frame buffer device +pci-stub: invalid id string "" isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found -Serial: 8250/16550 driver8 ports, IRQ sharing enabled +Non-volatile memory driver v1.3 +Linux agpgart interface v0.103 +Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A @@ -251,6 +293,7 @@ serial 0000:00:0b.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11 0000:00:0b.0: ttyS6 at I/O 0x18c0 (irq = 11) is a 16550A 0000:00:0b.0: ttyS7 at I/O 0x18b8 (irq = 11) is a 16550A +Fixed MDIO Bus: probed PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 @@ -259,252 +302,198 @@ cpuidle: using governor menu TCP cubic registered Using IPI No-Shortcut mode +PM: Checking image partition /dev/disk/by-id/ata-WDC_WD400BB-23JHA1_WD-WMAMA1000905-part2 +PM: Resume from disk failed. registered taskstats version 1 -Freeing unused kernel memory: 280k freed -Write protecting the kernel text: 2300k -Write protecting the kernel read-only data: 1732k -ACPI: CPU0 (power states: C1[C1] C2[C2]) -processor ACPI_CPU:00: registered as cooling_device0 -ACPI: Processor [CPU0] (supports 16 throttling states) -ACPI: No dock devices found. + Magic number: 7:428:803 +Freeing unused kernel memory: 400k freed +Write protecting the kernel text: 3232k +Write protecting the kernel read-only data: 2120k SCSI subsystem initialized libata version 3.00 loaded. -pata_via 0000:00:07.1: version 0.3.3 +pata_via 0000:00:07.1: version 0.3.4 scsi0 : pata_via scsi1 : pata_via ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1840 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1848 irq 15 ata1: port disabled. ignoring. -Marking TSC unstable due to TSC halts in idle -ata2.00: ATA-6: Maxtor 4D040H2, DAH017K0, max UDMA/100 +ata2.00: ATA-6: WDC WD400BB-23JHA1, 06.01C06, max UDMA/100 ata2.00: 78156288 sectors, multi 16: LBA ata2.00: limited to UDMA/33 due to 40-wire cable ata2.00: configured for UDMA/33 -scsi 1:0:0:0: Direct-Access ATA Maxtor 4D040H2 DAH0 PQ: 0 ANSI: 5 +scsi 1:0:0:0: Direct-Access ATA WDC WD400BB-23JH 06.0 PQ: 0 ANSI: 5 Uniform Multi-Platform E-IDE driver -BIOS EDD facility v0.16 2004-Jun-25, 2 devices found +Marking TSC unstable due to TSC halts in idle +Switching to clocksource acpi_pm +BIOS EDD facility v0.16 2004-Jun-25, 1 devices found udevd version 128 started -sd 1:0:0:0: [sda] 78156288 512-byte hardware sectors: (40.0GB/37.2GiB) +sd 1:0:0:0: [sda] 78156288 512-byte logical blocks: (40.0 GB/37.2 GiB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA -sd 1:0:0:0: [sda] 78156288 512-byte hardware sectors: (40.0GB/37.2GiB) -sd 1:0:0:0: [sda] Write Protect is off -sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 -sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA - sda:<3>ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 -ata2.00: BMDMA stat 0x24 -ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in - res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) -ata2.00: status: { DRDY ERR } -ata2.00: error: { ICRC ABRT } -ata2: soft resetting link + sda: sda1 sda2 sda3 +sd 1:0:0:0: [sda] Attached SCSI disk usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb -USB Universal Host Controller Interface driver v3.0 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver +uhci_hcd: USB Universal Host Controller Interface driver ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 9, io base 0x00001800 -usb usb1: configuration #1 chosen from 1 choice -hub 1-0:1.0: USB hub found -hub 1-0:1.0: 2 ports detected -ata2.00: configured for UDMA/33 -ata2: EH complete -ata2.00: limiting speed to UDMA/25:PIO4 -ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 -ata2.00: BMDMA stat 0x24 -ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in - res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) -ata2.00: status: { DRDY ERR } -ata2.00: error: { ICRC ABRT } -ata2: soft resetting link usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller -usb usb1: Manufacturer: Linux 2.6.27.19-5-default uhci_hcd +usb usb1: Manufacturer: Linux 2.6.32.10-0.4-default uhci_hcd usb usb1: SerialNumber: 0000:00:07.2 +usb usb1: configuration #1 chosen from 1 choice +hub 1-0:1.0: USB hub found +hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:07.3: PCI INT D -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:07.3: UHCI Host Controller uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:07.3: irq 9, io base 0x00001820 -usb usb2: configuration #1 chosen from 1 choice -hub 2-0:1.0: USB hub found -hub 2-0:1.0: 2 ports detected -ata2.00: configured for UDMA/25 -ata2: EH complete -usb 1-1: new full speed USB device using uhci_hcd and address 2 -ata2.00: limiting speed to PIO4 -ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 -ata2.00: BMDMA stat 0x24 -ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in - res 51/84:00:00:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error) -ata2.00: status: { DRDY ERR } -ata2.00: error: { ICRC ABRT } -ata2: soft resetting link usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller -usb usb2: Manufacturer: Linux 2.6.27.19-5-default uhci_hcd +usb usb2: Manufacturer: Linux 2.6.32.10-0.4-default uhci_hcd usb usb2: SerialNumber: 0000:00:07.3 -ata2.00: configured for PIO4 -ata2: EH complete -sd 1:0:0:0: [sda] 78156288 512-byte hardware sectors: (40.0GB/37.2GiB) -sd 1:0:0:0: [sda] Write Protect is off -sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 -sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA - sda1 sda2 -sd 1:0:0:0: [sda] Attached SCSI disk -sd 1:0:0:0: [sda] 78156288 512-byte hardware sectors: (40.0GB/37.2GiB) -sd 1:0:0:0: [sda] Write Protect is off -sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 -sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA -sda: detected capacity change from 0 to 40016019456 -usb 1-1: configuration #1 chosen from 1 choice -usb 1-1: New USB device found, idVendor=090c, idProduct=1000 -usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 -usb 1-1: Product: USB DISK -usb 1-1: Manufacturer: SMI Corporation -usb 1-1: SerialNumber: AAD7593000008325 -usb 1-2: new full speed USB device using uhci_hcd and address 3 -usb 1-2: configuration #1 chosen from 1 choice -usb 1-2: New USB device found, idVendor=0984, idProduct=0066 -usb 1-2: New USB device strings: Mfr=74, Product=57, SerialNumber=44 -usb 1-2: Product: USB_MultiBurner3 -usb 1-2: Manufacturer: Lenovo -usb 1-2: SerialNumber: 070801035989 +usb usb2: configuration #1 chosen from 1 choice +hub 2-0:1.0: USB hub found +hub 2-0:1.0: 2 ports detected usb 2-1: new full speed USB device using uhci_hcd and address 2 -usb 2-1: configuration #1 chosen from 1 choice -hub 2-1:1.0: USB hub found -hub 2-1:1.0: 4 ports detected -PM: Starting manual resume from disk usb 2-1: New USB device found, idVendor=04b3, idProduct=3016 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1: Product: USB 1.1 2 port downstream low-power hub usb 2-1: Manufacturer: Lite-On Tech +usb 2-1: configuration #1 chosen from 1 choice +hub 2-1:1.0: USB hub found +hub 2-1:1.0: 4 ports detected +PM: Marking nosave pages: 0000000000002000 - 0000000000006000 +PM: Marking nosave pages: 000000000009f000 - 0000000000100000 +PM: Basic memory bitmaps created +PM: Basic memory bitmaps freed +PM: Starting manual resume from disk +PM: Resume from partition 8:2 +PM: Checking hibernation image. +PM: Error -22 checking image file +PM: Resume from disk failed. usb 2-1.3: new low speed USB device using uhci_hcd and address 3 -usb 2-1.3: configuration #1 chosen from 1 choice usb 2-1.3: New USB device found, idVendor=04b3, idProduct=3019 usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1.3: Product: IBM USB Travel Keyboard with UltraNav usb 2-1.3: Manufacturer: Lite-On Tech +usb 2-1.3: configuration #1 chosen from 1 choice +usbcore: registered new interface driver hiddev +input: Lite-On Tech IBM USB Travel Keyboard with UltraNav as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.3/2-1.3:1.0/input/input0 +generic-usb 0003:04B3:3019.0001: input,hidraw0: USB HID v1.00 Keyboard [Lite-On Tech IBM USB Travel Keyboard with UltraNav] on usb-0000:00:07.3-1.3/input0 +input: Lite-On Tech IBM USB Travel Keyboard with UltraNav as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.3/2-1.3:1.1/input/input1 +generic-usb 0003:04B3:3019.0002: input,hidraw1: USB HID v1.00 Device [Lite-On Tech IBM USB Travel Keyboard with UltraNav] on usb-0000:00:07.3-1.3/input1 +usbcore: registered new interface driver usbhid +usbhid: v2.6:USB HID core driver usb 2-1.4: new low speed USB device using uhci_hcd and address 4 -usb 2-1.4: configuration #1 chosen from 1 choice +kjournald starting. Commit interval 15 seconds +EXT3 FS on sda3, internal journal +EXT3-fs: mounted filesystem with ordered data mode. usb 2-1.4: New USB device found, idVendor=06cb, idProduct=0009 usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1.4: Product: Composite TouchPad / TrackPoint usb 2-1.4: Manufacturer: Synaptics Inc. -usbcore: registered new interface driver hiddev -input: Lite-On Tech IBM USB Travel Keyboard with UltraNav as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.3/2-1.3:1.0/input/input0 -input,hidraw0: USB HID v1.00 Keyboard [Lite-On Tech IBM USB Travel Keyboard with UltraNav] on usb-0000:00:07.3-1.3 -input: Lite-On Tech IBM USB Travel Keyboard with UltraNav as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.3/2-1.3:1.1/input/input1 -input,hidraw1: USB HID v1.00 Device [Lite-On Tech IBM USB Travel Keyboard with UltraNav] on usb-0000:00:07.3-1.3 +usb 2-1.4: configuration #1 chosen from 1 choice input: Synaptics Inc. Composite TouchPad / TrackPoint as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.4/2-1.4:1.0/input/input2 -input,hidraw2: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:00:07.3-1.4 -kjournald starting. Commit interval 5 seconds -EXT3 FS on sda2, internal journal -EXT3-fs: mounted filesystem with ordered data mode. +generic-usb 0003:06CB:0009.0003: input,hidraw2: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:00:07.3-1.4/input0 input: Synaptics Inc. Composite TouchPad / TrackPoint as /devices/pci0000:00/0000:00:07.3/usb2/2-1/2-1.4/2-1.4:1.1/input/input3 -input,hidraw3: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:00:07.3-1.4 -usbcore: registered new interface driver usbhid -usbhid: v2.6:USB HID core driver +generic-usb 0003:06CB:0009.0004: input,hidraw3: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:00:07.3-1.4/input1 udevd version 128 started -sd 1:0:0:0: Attached scsi generic sg0 type 0 -Linux agpgart interface v0.103 -Initializing USB Mass Storage driver... -scsi2 : SCSI emulation for USB Mass Storage devices -scsi3 : SCSI emulation for USB Mass Storage devices -usbcore: registered new interface driver usb-storage -USB Mass Storage support registered. -usb-storage: device found at 3 -usb-storage: waiting for device to settle before scanning -usb-storage: device found at 2 -usb-storage: waiting for device to settle before scanning +input: PC Speaker as /devices/platform/pcspkr/input/input4 agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset agpgart-via 0000:00:00.0: AGP aperture is 16M @ 0xfd000000 +sd 1:0:0:0: Attached scsi generic sg0 type 0 +natsemi dp8381x driver, version 2.1, Sept 11, 2006 + originally by Donald Becker <becker@xxxxxxxxx> + 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder +natsemi 0000:00:0d.0: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9 +natsemi eth0: NatSemi DP8381[56] at 0xfb000000 (0000:00:0d.0), 00:0d:60:02:8b:98, IRQ 9, port TP. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 -input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4 -ACPI: Power Button (FF) [PWRF] -input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5 -shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 +input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5 +ACPI: Power Button [PWRB] +input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6 +ACPI: Power Button [PWRF] parport_pc: VIA 686A/8231 detected parport_pc: probing current configuration parport_pc: Current parallel port base: 0x378 parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] -ACPI: Power Button (CM) [PWRB] -scsi 2:0:0:0: Direct-Access USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS -sd 2:0:0:0: [sdb] 15663104 512-byte hardware sectors: (8.01GB/7.46GiB) -scsi 3:0:0:0: CD-ROM LENOVO USB_MultiBurner3 NL31 PQ: 0 ANSI: 0 -scsi 3:0:0:0: Attached scsi generic sg1 type 5 -usb-storage: device scan complete -sd 2:0:0:0: [sdb] Write Protect is off -sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 -sd 2:0:0:0: [sdb] Assuming drive cache: write through -parport_pc: VIA parallel port: io=0x378, irq=7 -sd 2:0:0:0: [sdb] 15663104 512-byte hardware sectors: (8.01GB/7.46GiB) -sd 2:0:0:0: [sdb] Write Protect is off -sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 -sd 2:0:0:0: [sdb] Assuming drive cache: write through - sdb: sdb1 -sd 2:0:0:0: [sdb] Attached SCSI removable disk -sd 2:0:0:0: Attached scsi generic sg2 type 0 -usb-storage: device scan complete +shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 +rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 +rtc0: alarms up to one year, y3k, 242 bytes nvram vt596_smbus 0000:00:07.4: SMBUS: Error: Host SMBus controller not enabled! - upgrade BIOS or use force=1 -natsemi dp8381x driver, version 2.1, Sept 11, 2006 - originally by Donald Becker <becker@xxxxxxxxx> - 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder -natsemi 0000:00:0d.0: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9 -natsemi eth0: NatSemi DP8381[56] at 0xfb000000 (0000:00:0d.0), 00:0d:60:02:8b:98, IRQ 9, port TP. -input: PC Speaker as /devices/platform/pcspkr/input/input6 +parport_pc: VIA parallel port: io=0x378, irq=7 +ppdev: user-space parallel port driver ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered VIA 82xx Audio 0000:00:07.5: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10 VIA 82xx Audio 0000:00:07.5: setting latency timer to 64 -rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 -rtc0: alarms up to one year, y3k -ppdev: user-space parallel port driver -sr0: scsi-1 drive -Uniform CD-ROM driver Revision: 3.20 -sr 3:0:0:0: Attached scsi CD-ROM sr0 -Adding 2096472k swap on /dev/sda1. Priority:-1 extents:1 across:2096472k +Adding 2096472k swap on /dev/sda2. Priority:-1 extents:1 across:2096472k device-mapper: uevent: version 1.0.3 -device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx +device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx loop: module loaded -- js suse labs -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
