On 9/18/09, vprabu vprabu <prabu_online2005@xxxxxxxxx> wrote: > Hi All, > > This is prabu . Hi > I am new to kernel hacking ; i had been an application guy; now focusing > into the fundamentals of linux kernel. I really have little knowledge about > the kernel, modules and auto loading of modules.After a lot of googling ,i > am now much perplexed :-). > > Most of the articles are contradictory to each > other and not very clear ( or not so simple at my level to comprehend) Heh, I think that's a common reaction. I don't know where there is a good introduction. What I would suggest is that you look at a working system. Any modern distro - although it may be better to avoid Debian since it alone uses its own rules, and Arch Linux, which has funky extra stuff for modules. If you have a concrete working system you can ask concrete questions of it :-). > 1. How does a linux distribution know which feature is to be set in kernel > and which one as a module. It varies. The distributions used to do modules for everything to avoid wasting memory. More recently, Moblin showed that you can boot faster by making some common drivers (and other features like filesystems) built in. It doesn't matter if a module might be required to boot less common systems (e.g. a specific ATA driver), because modules can be included in the initramfs, which is loaded alongside the kernel by the boot loader. > 2. Now after installation, i reboot the server ....( COLDPLUG ) > > *. Does the hardware probing is done first and then the relevant drivers are > loaded for the hardware found. If so how is this achieved. > > ( or ) > > *. Else if the hardware driver is loaded FIRST from modprobe.conf and does > it go in search of a corresponding device supported by the driver? > > ie. Need to know a device is found first and its corresponding driver is > loaded or the driver is loaded first which brings up the device The first one (for modern buses). Each device has an identifier in a standard format and location, e.g. on the PCI bus, each device has a vendor and device ID. The bus code reads all these IDs, and is then causes the appropriate modules to be loaded. Look in sysfs under /sys/bus/*/devices; each device has a "modalias" file. That's short for "module alias". Search /lib/udev/rules.d for this; you will see an invocation of "modprobe" to load the module with this alias. In udev coldplug the rules are processed for each hardware device; this is achieved by the command "udevadm trigger". > 3. HOTPLUG ...... > > > *. I now add a new network card to the PCI slot. ( 2.6 ) > > *. I assume that the PCI controller sends a signal to the kernel that a new > device is added > > *. The new device's firmware details like vendor id, prod id is propogated > to /sys file system. > > *. udevd tries to load the device drivers containing that particular vendor > id in /lib/modules/kernel.xx/net > > i have a doubt ... like.. does it search only /etc/modprobe.conf or all the > modules under /lib/modules. All modules under /lib/modules. The "modalias"es are built into the modules. They are extracted by the "depmod" command into /lib/modules/*/module.aliases.bin, which "modprobe" can then search efficiently. You can see these builtin aliases using "modinfo". (the .bin files were added recently; previously the search was not quite so efficient :-). > > > 4. How does the same hotplug and cold plug happen in case of 2.4 kernels. > > where does kmod , kerneld come into picture We're not interested in them, it is too long ago and no-one supports it. > 5. What is the main role of rc.sysinit -- does this handle device and > drivers. Dunno, this probably varies between distros. > 6. Dont know when to put an entry in modprobe.conf and when not to. Don't :-). a) Don't use modprobe.conf. use /etc/modprobe.d/some-file-here.conf b) The modaliases used to load drivers should be built into the modules, as described above. There may be some exceptions where this is still not done. The situation has improved better recently; if you find such a case you should consider it a bug. > 7. why does lsmod show something different from modprobe -c There is no obvious connection between these two, please elaborate as to what you are expecting. lsmod lists loaded modules. modprobe -c dumps the entire configuration, including /etc/modprobe.d and /lib/modules/$version/modules.alias etc. > 8. How does modprobe -c get those values. why does it vary with lsmod output See above > 9. There are two SCSI hostadapters of same type. Do i need to load the > module twice for it or once? Once. > In simple words how a device driver is loaded at boot/hotplug for 2.4 and > 2.6 kernels > > > I know each one is inter-related but dont know how they are?. Very. "Coldplug" i.e. "udevadm trigger" simply synthesizes hotplug events. It replays the events which happened earlier, i.e. before userspace was up and running. Both cases look the same to the main udev daemon. > I cant find > any good article to explain the > > working of modules in simple words (both 2.4 / 2.6 with examples) > > Any help in this regard is much appreciated.... > > Prabu Best wishes, hope this helps. Alan -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
