> Kenji Kaneshige wrote: > > Thank you for sending the information. I understood your > hotplug slot can be handled by acpiphp or pciehp. > More majordomo info at http://vger.kernel.org/majordomo-info.html Tested this with 2.6.28.3 and details below: >Could you give me the following additional information? >o My understanding about the problem is: > - Bad IRQ happen when you hot-add the device, I don't see bad IRQ stack trace anymore, based on the steps you suggested. May be this is because I did not have hotplug driverloaded (and diff kernel build config) ? > - and the device is not found in the lspci output YES > - and the device didn't show up under sysfs > Am I correct? YES > o Details about the steps to reproduce the problem. - boot the box with 2.6.28.3 - # /sbin/modprobe pciehp pciehp_debug - lspci - Insert the PCI express card on the hot swap slot and wait for 2 mins - lspci <-- this does not show the PCI express device (The same device shows up in lspci and sysfs during cold boot ) > o Does the problem happen with both acpiphp and pciehp? That is correct. > o The pciehp's debug output. We can get this as follows. # /sbin/modprobe pciehp pciehp_debug # dmesg | grep pciehp pciehp 0000:00:09.0:pcie02: Hotplug Controller: pciehp 0000:00:09.0:pcie02: Seg/Bus/Dev/Func/IRQ : 0000:00:09.0 IRQ 2295 pciehp 0000:00:09.0:pcie02: Vendor ID : 0x8086 pciehp 0000:00:09.0:pcie02: Device ID : 0x3410 pciehp 0000:00:09.0:pcie02: Subsystem ID : 0x0000 pciehp 0000:00:09.0:pcie02: Subsystem Vendor ID : 0x0000 pciehp 0000:00:09.0:pcie02: PCIe Cap offset : 0x90 pciehp 0000:00:09.0:pcie02: Slot Capabilities : 0x0302005f pciehp 0000:00:09.0:pcie02: Physical Slot Number : 96 pciehp 0000:00:09.0:pcie02: Attention Button : yes pciehp 0000:00:09.0:pcie02: Power Controller : yes pciehp 0000:00:09.0:pcie02: MRL Sensor : yes pciehp 0000:00:09.0:pcie02: Attention Indicator : yes pciehp 0000:00:09.0:pcie02: Power Indicator : yes pciehp 0000:00:09.0:pcie02: Hot-Plug Surprise : no pciehp 0000:00:09.0:pcie02: EMI Present : yes pciehp 0000:00:09.0:pcie02: Command Completed : yes pciehp 0000:00:09.0:pcie02: Slot Status : 0x0020 pciehp 0000:00:09.0:pcie02: Slot Control : 0x078f pciehp 0000:00:09.0:pcie02: Link Active Reporting supported pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec pciehp 0000:00:09.0:pcie02: HPC vendor_id 8086 device_id 3410 ss_vid 0 ss_did 0 pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec pciehp 0000:00:09.0:pcie02: Registering domain:bus:dev=0000:09:00 hp_slot=0 sun=60 slot_device_offset=0 pciehp 0000:00:09.0:pcie02: get_power_status: physical_slot = 96 pciehp 0000:00:09.0:pcie02: hpc_get_power_status: SLOTCTRL a8 value read 7bf pciehp 0000:00:09.0:pcie02: get_attention_status: physical_slot = 96 pciehp 0000:00:09.0:pcie02: hpc_get_attention_status: SLOTCTRL a8, value read 7bf pciehp 0000:00:09.0:pcie02: get_latch_status: physical_slot = 96 pciehp 0000:00:09.0:pcie02: get_adapter_status: physical_slot = 96 pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: slot->hp_slot 0 pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec pciehp 0000:00:09.0:pcie02: hpc_power_off_slot: SLOTCTRL a8 write cmd 400 pciehp 0000:00:09.0:pcie02: service driver pciehp loaded pciehp: pcie_port_service_register = 0 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 -- Hot plug PCI express card and wait for 2 mins -- no additional out put from dmesg [root@localhost test]# /sbin/rmmod pciehp [root@localhost test]# dmesg | grep pciehp -- Additional output from dmesg after pciehp is unloaded ( but the express card is still present in the slot):- pciehp: unload_pciehpd() pciehp 0000:00:09.0:pcie02: unloading service driver pciehp pciehp 0000:00:09.0:pcie02: release_slot: physical_slot = 96 pciehp 0000:00:09.0:pcie02: Command not completed in 1000 msec pciehp 0000:00:09.0:pcie02: pcie_isr: intr_loc 8 pciehp 0000:00:09.0:pcie02: Presence/Notify input change pciehp 0000:00:09.0:pcie02: Card present on Slot(øu'?) -- removed the PCI express card from the slot [root@localhost test]# ls -lt /sys/bus/pci/slots total 0 [root@localhost test]# /sbin/modprobe acpiphp debug [root@localhost test]# dmesg | grep acpiphp acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:09.0 acpiphp_glue: found ACPI PCI Hotplug slot 2 at PCI 0000:09:00 acpiphp: Slot [2] registered acpiphp_glue: Bus 0000:09 has 1 slot acpiphp_glue: Total 1 slots [root@localhost test]# [root@localhost test]# ls -lt /sys/bus/pci/slots total 0 drwxr-xr-x 2 root root 0 2009-02-04 09:59 2 --- Insert PCI express card in the slot [root@localhost test]# dmesg | grep acpiphp [root@localhost test]# lspci | wc 105 1284 9203 [root@localhost test]# ls -lt /sys/bus/pci/slots/2/ total 0 -r--r--r-- 1 root root 4096 2009-02-04 10:01 adapter -r--r--r-- 1 root root 4096 2009-02-04 10:01 address -rw-r--r-- 1 root root 4096 2009-02-04 10:01 attention -r--r--r-- 1 root root 4096 2009-02-04 10:01 latch -rw-r--r-- 1 root root 4096 2009-02-04 10:01 power [root@localhost test]# [root@localhost test]# /sbin/rmmod acpiphp [root@localhost test]# dmesg | grep acpiphp acpiphp: Slot [2] unregistered acpiphp: release_slot - physical_slot = 2 [root@localhost test]# _________________________________________________________________ Windows Live™: Keep your life in sync. http://windowslive.com/howitworks?ocid=TXT_TAGLM_WL_t1_allup_howitworks_022009-- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
