Re: [BUG][BISECTED] Freeze at loading init ramdisk

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jan 18, 2024 at 09:04:05PM +0100, Mirsad Todorovac wrote:
> 
> 
> On 1/18/24 08:45, Uwe Kleine-König wrote:
> > Hello Mirsad,
> > 
> > On Wed, Jan 17, 2024 at 07:47:49PM +0100, Mirsad Todorovac wrote:
> > > On 1/16/24 01:32, Mirsad Todorovac wrote:
> > > > On the Ubuntu 22.04 LTS Jammy platform, on a mainline vanilla torvalds tree kernel, the boot
> > > > freezes upon first two lines and before any systemd messages.
> > > > 
> > > > (Please find the config attached.)
> > > > 
> > > > Bisecting the bug led to this result:
> > > > 
> > > > marvin@defiant:~/linux/kernel/linux_torvalds$ git bisect good
> > > > d97a78423c33f68ca6543de510a409167baed6f5 is the first bad commit
> > > > commit d97a78423c33f68ca6543de510a409167baed6f5
> > > > Merge: 61da593f4458 689237ab37c5
> > > > Author: Linus Torvalds <torvalds@xxxxxxxxxxxxxxxxxxxx>
> > > > Date:   Fri Jan 12 14:38:08 2024 -0800
> > > > 
> > > > [...]
> > > > 
> > > > Hope this helps.
> > > 
> > > P.S.
> > > 
> > > As I see that this is a larger merge commit, with 5K+ lines changed, I don't think I can
> > > bisect further to determine the culprit.
> > 
> > Actually it's not that hard. If a merge commit is the first bad commit
> > for a bisection, either the merge wasn't done correctly (less likely,
> > looking at d97a78423c33f68ca6543de510a409167baed6f5 I'd bet this isn't
> > the problem); or changes on different sides conflict or you did
> > something wrong during bisection.
> > 
> > To rule out the third option, you can just retest d97a78423c33,
> > 61da593f4458 and 689237ab37c5. If d97a78423c33 is the only bad one, you
> > did it right.
> 
> This was confirmed.
> 
> > Then to further debug the second option you can find out the offending
> > commit on each side with a bisection as follows, here for the RHS (i.e.
> > 689237ab37c5):
> > 
> > 	git bisect start 689237ab37c5 $(git merge-base 61da593f4458 689237ab37c5)
> > 
> > and then in each bisection step do:
> > 
> > 	git merge --no-commit 61da593f4458
> > 	test if the problem is present
> > 	git reset --hard
> > 	git bisect good/bad
> > 
> > In this case you get merge conflicts in drivers/video/fbdev/amba-clcd.c
> > and drivers/video/fbdev/vermilion/vermilion.c. In the assumption that
> > you don't have these enabled in your .config, you can just ignore these.
> > 
> > Side note: A problem during bisection can be that the .config changes
> > along the process. You should put your config into (say)
> > arch/x86/configs/lala_defconfig and do
> > 
> > 	make lala_defconfig
> > 
> > before building each step to prevent this.
> 
> I must have done something wrong:
> 
> marvin@defiant:~/linux/kernel/linux_torvalds$ git bisect log
> # bad: [689237ab37c59b9909bc9371d7fece3081683fba] fbdev/intelfb: Remove driver
> # good: [de927f6c0b07d9e698416c5b287c521b07694cac] Merge tag 's390-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
> git bisect start '689237ab37c5' 'de927f6c0b07d9e698416c5b287c521b07694cac'
> # good: [d9f25b59ed85ae45801cf45fe17eb269b0ef3038] fbdev: Remove support for Carillo Ranch driver
> git bisect good d9f25b59ed85ae45801cf45fe17eb269b0ef3038
> # good: [e2e0b838a1849f92612a8305c09aaf31bf824350] video/sticore: Remove info field from STI struct
> git bisect good e2e0b838a1849f92612a8305c09aaf31bf824350
> # good: [778e73d2411abc8f3a2d60dbf038acaec218792e] drm/hyperv: Remove firmware framebuffers with aperture helper
> git bisect good 778e73d2411abc8f3a2d60dbf038acaec218792e
> # good: [df67699c9cb0ceb70f6cc60630ca938c06773eda] firmware/sysfb: Clear screen_info state after consuming it
> git bisect good df67699c9cb0ceb70f6cc60630ca938c06773eda
> marvin@defiant:~/linux/kernel/linux_torvalds$
> 
> with the error:
> 
> marvin@defiant:~/linux/kernel/linux_torvalds$ git bisect good
> Bisecting: 0 revisions left to test after this (roughly 0 steps)
> drivers/video/fbdev/amba-clcd.c: needs merge
> drivers/video/fbdev/vermilion/vermilion.c: needs merge
> error: you need to resolve your current index first

It seems you forgot the "git reset --hard" step.  Doing it in this state
should still be possible.

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux SoC]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux