- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
.../device_drivers/dec/{dmfe.txt => dmfe.rst} | 35 +++++++++++--------
.../networking/device_drivers/index.rst | 1 +
MAINTAINERS | 2 +-
drivers/net/ethernet/dec/tulip/Kconfig | 2 +-
4 files changed, 23 insertions(+), 17 deletions(-)
rename Documentation/networking/device_drivers/dec/{dmfe.txt => dmfe.rst} (68%)
diff --git a/Documentation/networking/device_drivers/dec/dmfe.txt b/Documentation/networking/device_drivers/dec/dmfe.rst
similarity index 68%
rename from Documentation/networking/device_drivers/dec/dmfe.txt
rename to Documentation/networking/device_drivers/dec/dmfe.rst
index 25320bf19c86..c4cf809cad84 100644
--- a/Documentation/networking/device_drivers/dec/dmfe.txt
+++ b/Documentation/networking/device_drivers/dec/dmfe.rst
@@ -1,6 +1,11 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==============================================================
+Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver for Linux
+==============================================================
+
Note: This driver doesn't have a maintainer.
-Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver for Linux.
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
@@ -16,29 +21,29 @@ GNU General Public License for more details.
This driver provides kernel support for Davicom DM9102(A)/DM9132/DM9801 ethernet cards ( CNET
10/100 ethernet cards uses Davicom chipset too, so this driver supports CNET cards too ).If you
didn't compile this driver as a module, it will automatically load itself on boot and print a
-line similar to :
+line similar to::
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
-If you compiled this driver as a module, you have to load it on boot.You can load it with command :
+If you compiled this driver as a module, you have to load it on boot.You can load it with command::
insmod dmfe
This way it will autodetect the device mode.This is the suggested way to load the module.Or you can pass
-a mode= setting to module while loading, like :
+a mode= setting to module while loading, like::
insmod dmfe mode=0 # Force 10M Half Duplex
insmod dmfe mode=1 # Force 100M Half Duplex
insmod dmfe mode=4 # Force 10M Full Duplex
insmod dmfe mode=5 # Force 100M Full Duplex
-Next you should configure your network interface with a command similar to :
+Next you should configure your network interface with a command similar to::
ifconfig eth0 172.22.3.18
- ^^^^^^^^^^^
+ ^^^^^^^^^^^
Your IP Address
-Then you may have to modify the default routing table with command :
+Then you may have to modify the default routing table with command::
route add default eth0
@@ -48,10 +53,10 @@ Now your ethernet card should be up and running.
TODO:
-Implement pci_driver::suspend() and pci_driver::resume() power management methods.
-Check on 64 bit boxes.
-Check and fix on big endian boxes.
-Test and make sure PCI latency is now correct for all cases.
+- Implement pci_driver::suspend() and pci_driver::resume() power management methods.
+- Check on 64 bit boxes.
+- Check and fix on big endian boxes.
+- Test and make sure PCI latency is now correct for all cases.
Authors:
@@ -60,7 +65,7 @@ Sten Wang <sten_wang@xxxxxxxxxxxxxx > : Original Author
Contributors:
-Marcelo Tosatti <marcelo@xxxxxxxxxxxxxxxx>
-Alan Cox <alan@xxxxxxxxxxxxxxxxxxx>
-Jeff Garzik <jgarzik@xxxxxxxxx>
-Vojtech Pavlik <vojtech@xxxxxxx>
+- Marcelo Tosatti <marcelo@xxxxxxxxxxxxxxxx>
+- Alan Cox <alan@xxxxxxxxxxxxxxxxxxx>
+- Jeff Garzik <jgarzik@xxxxxxxxx>
+- Vojtech Pavlik <vojtech@xxxxxxx>
diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst
index 4ad13ffb5800..09728e964ce1 100644
--- a/Documentation/networking/device_drivers/index.rst
+++ b/Documentation/networking/device_drivers/index.rst
@@ -35,6 +35,7 @@ Contents:
cirrus/cs89x0
davicom/dm9000
dec/de4x5
+ dec/dmfe
.. only:: subproject and html
diff --git a/MAINTAINERS b/MAINTAINERS
index 91098b704635..b92568479a71 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4710,7 +4710,7 @@ F: net/ax25/sysctl_net_ax25.c
DAVICOM FAST ETHERNET (DMFE) NETWORK DRIVER
L: netdev@xxxxxxxxxxxxxxx
S: Orphan
-F: Documentation/networking/device_drivers/dec/dmfe.txt
+F: Documentation/networking/device_drivers/dec/dmfe.rst
F: drivers/net/ethernet/dec/tulip/dmfe.c
DC390/AM53C974 SCSI driver
diff --git a/drivers/net/ethernet/dec/tulip/Kconfig b/drivers/net/ethernet/dec/tulip/Kconfig
index 8c4245d94bb2..177f36f4b89d 100644
--- a/drivers/net/ethernet/dec/tulip/Kconfig
+++ b/drivers/net/ethernet/dec/tulip/Kconfig
@@ -138,7 +138,7 @@ config DM9102
This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
Davicom (<http://www.davicom.com.tw/>). If you have such a network
(Ethernet) card, say Y. Some information is contained in the file
- <file:Documentation/networking/device_drivers/dec/dmfe.txt>.
+ <file:Documentation/networking/device_drivers/dec/dmfe.rst>.
To compile this driver as a module, choose M here. The module will
be called dmfe.
--
2.25.4
