Re: [PATCH v2] parisc: use memblock_alloc() instead of custom get_memblock()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 21.02.19 10:07, Mike Rapoport wrote:
> On Tue, Feb 12, 2019 at 05:16:12PM +0200, Mike Rapoport wrote:
>> The get_memblock() function implements custom bottom-up memblock allocator.
>> Setting 'memblock_bottom_up = true' before any memblock allocation is done
>> allows replacing get_memblock() calls with memblock_alloc().

>> Signed-off-by: Mike Rapoport <rppt@xxxxxxxxxxxxx>

Acked-by: Helge Deller <deller@xxxxxx>
Tested-by: Helge Deller <deller@xxxxxx>

Thanks!
Shall I push the patch upstream with the parisc tree?

Helge



>> ---
>> v2: fix allocation alignment
>>
>>  arch/parisc/mm/init.c | 52 +++++++++++++++++++--------------------------------
>>  1 file changed, 19 insertions(+), 33 deletions(-)
>>
>> diff --git a/arch/parisc/mm/init.c b/arch/parisc/mm/init.c
>> index 059187a..d0b1662 100644
>> --- a/arch/parisc/mm/init.c
>> +++ b/arch/parisc/mm/init.c
>> @@ -79,36 +79,6 @@ static struct resource sysram_resources[MAX_PHYSMEM_RANGES] __read_mostly;
>>  physmem_range_t pmem_ranges[MAX_PHYSMEM_RANGES] __read_mostly;
>>  int npmem_ranges __read_mostly;
>>  
>> -/*
>> - * get_memblock() allocates pages via memblock.
>> - * We can't use memblock_find_in_range(0, KERNEL_INITIAL_SIZE) here since it
>> - * doesn't allocate from bottom to top which is needed because we only created
>> - * the initial mapping up to KERNEL_INITIAL_SIZE in the assembly bootup code.
>> - */
>> -static void * __init get_memblock(unsigned long size)
>> -{
>> -	static phys_addr_t search_addr __initdata;
>> -	phys_addr_t phys;
>> -
>> -	if (!search_addr)
>> -		search_addr = PAGE_ALIGN(__pa((unsigned long) &_end));
>> -	search_addr = ALIGN(search_addr, size);
>> -	while (!memblock_is_region_memory(search_addr, size) ||
>> -		memblock_is_region_reserved(search_addr, size)) {
>> -		search_addr += size;
>> -	}
>> -	phys = search_addr;
>> -
>> -	if (phys)
>> -		memblock_reserve(phys, size);
>> -	else
>> -		panic("get_memblock() failed.\n");
>> -
>> -	memset(__va(phys), 0, size);
>> -
>> -	return __va(phys);
>> -}
>> -
>>  #ifdef CONFIG_64BIT
>>  #define MAX_MEM         (~0UL)
>>  #else /* !CONFIG_64BIT */
>> @@ -321,6 +291,13 @@ static void __init setup_bootmem(void)
>>  			max_pfn = start_pfn + npages;
>>  	}
>>  
>> +	/*
>> +	 * We can't use memblock top-down allocations because we only
>> +	 * created the initial mapping up to KERNEL_INITIAL_SIZE in
>> +	 * the assembly bootup code.
>> +	 */
>> +	memblock_set_bottom_up(true);
>> +
>>  	/* IOMMU is always used to access "high mem" on those boxes
>>  	 * that can support enough mem that a PCI device couldn't
>>  	 * directly DMA to any physical addresses.
>> @@ -442,7 +419,10 @@ static void __init map_pages(unsigned long start_vaddr,
>>  		 */
>>  
>>  		if (!pmd) {
>> -			pmd = (pmd_t *) get_memblock(PAGE_SIZE << PMD_ORDER);
>> +			pmd = memblock_alloc(PAGE_SIZE << PMD_ORDER,
>> +					     PAGE_SIZE << PMD_ORDER);
>> +			if (!pmd)
>> +				panic("pmd allocation failed.\n");
>>  			pmd = (pmd_t *) __pa(pmd);
>>  		}
>>  
>> @@ -461,7 +441,10 @@ static void __init map_pages(unsigned long start_vaddr,
>>  
>>  			pg_table = (pte_t *)pmd_address(*pmd);
>>  			if (!pg_table) {
>> -				pg_table = (pte_t *) get_memblock(PAGE_SIZE);
>> +				pg_table = memblock_alloc(PAGE_SIZE,
>> +							  PAGE_SIZE);
>> +				if (!pg_table)
>> +					panic("page table allocation failed\n");
>>  				pg_table = (pte_t *) __pa(pg_table);
>>  			}
>>  
>> @@ -700,7 +683,10 @@ static void __init pagetable_init(void)
>>  	}
>>  #endif
>>  
>> -	empty_zero_page = get_memblock(PAGE_SIZE);
>> +	empty_zero_page = memblock_alloc(PAGE_SIZE, PAGE_SIZE);
>> +	if (!empty_zero_page)
>> +		panic("zero page allocation failed.\n");
>> +
>>  }
>>  
>>  static void __init gateway_init(void)
>> -- 
>> 2.7.4
>>
> 




[Index of Archives]     [Linux SoC]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux