Hi Christoph,
On Fri, 2018-04-20 at 10:02 +0200, Christoph Hellwig wrote:
> Switch to the generic noncoherent direct mapping implementation.
>
> Signed-off-by: Christoph Hellwig <hch@xxxxxx>
> ---
> arch/arc/Kconfig | 4 +
> arch/arc/include/asm/Kbuild | 1 +
> arch/arc/include/asm/dma-mapping.h | 21 -----
> arch/arc/mm/dma.c | 141 +++--------------------------
> 4 files changed, 19 insertions(+), 148 deletions(-)
> delete mode 100644 arch/arc/include/asm/dma-mapping.h
>
[snip]
> @@ -135,7 +134,7 @@ static int arc_dma_mmap(struct device *dev, struct vm_area_struct *vma,
> * CPU accesses page via normal paddr, thus needs to explicitly made
> * consistent before each use
> */
> -static void _dma_cache_sync(phys_addr_t paddr, size_t size,
> +static void _dma_cache_sync(struct device *dev, phys_addr_t paddr size_t size,
> enum dma_data_direction dir)
Seems like there's a missing comma:
----------------------------------->8------------------------------------
--- a/arch/arc/mm/dma.c
+++ b/arch/arc/mm/dma.c
@@ -134,7 +134,7 @@ int arch_dma_mmap(struct device *dev, struct vm_area_struct *vma,
* CPU accesses page via normal paddr, thus needs to explicitly made
* consistent before each use
*/
-static void _dma_cache_sync(struct device *dev, phys_addr_t paddr size_t size,
+static void _dma_cache_sync(struct device *dev, phys_addr_t paddr, size_t size,
enum dma_data_direction dir)
{
switch (dir) {
----------------------------------->8------------------------------------
Which is actually strange as I would expect ARC code to be built by bots.
Anyways with above fix I do see problems with both USB and Ethernet controllers
on ARC HSDK board.
----------------------------------->8------------------------------------
usb 1-1: new high-speed USB device number 2 using ehci-platform
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb 1-1: new high-speed USB device number 3 using ehci-platform
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb usb1-port1: attempt power cycle
usb 1-1: new high-speed USB device number 4 using ehci-platform
usb 1-1: device not accepting address 4, error -32
usb 1-1: new high-speed USB device number 5 using ehci-platform
usb 1-1: device not accepting address 5, error -32
...
# wget ftp://ftp.denx.de/pub/u-boot/u-boot-1.0.0.tar.bz2
Connecting to ftp.denx.de (81.169.202.6:21)
wget: can't connect to remote host (81.169.202.6): No route to host
----------------------------------->8------------------------------------
Will all patches from the series reverted (i.e. with
your base-line) all issues go away.
I'll need to spend more time on checking what's actually wrong.
-Alexey
P.S. Note to my ARC colleagues - it's required to disable IO Coherency
to get DMA ops really used, it could be obviously done with:
----------------------------------->8------------------------------------
--- a/arch/arc/mm/cache.c
+++ b/arch/arc/mm/cache.c
@@ -27,7 +27,7 @@
static int l2_line_sz;
static int ioc_exists;
-int slc_enable = 1, ioc_enable = 1;
+int slc_enable = 1, ioc_enable = 0;
unsigned long perip_base = ARC_UNCACHED_ADDR_SPACE; /* legacy value for boot */
unsigned long perip_end = 0xFFFFFFFF; /* legacy value */
----------------------------------->8------------------------------------
��.n��������+%������w��{.n�����{�������{ay� ʇڙ���f���h������_�(�階�ݢj"��������G����?���&��
