hi,
today i checked the support of 64bit on my j5600. latest kernel
that successfully (and still) run it was 2.6.22, latest one i tried
(and still fails) is a fresh 2.6.32.
i have not any specific knowlwdge of the beast, only a pile of manuals
that i will use to try to understand what's wrong.
only, if anybody has a hint to point me in the right direction i would
save a lot of time. i attached the kernel boot log and the output of
ser pim firmware command.
best regards,
Domenico
-----[ Domenico Andreoli, aka cavok
--[ http://www.dandreoli.com/gpgkey.asc
---[ 3A0F 2F80 F79C 678A 8936 4FEE 0677 9033 A20E BC50
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/sda3 panic=60 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF64 executable
Entry 00100000 first 00100000 n 2
Segment 0 load 00100000 size 6139904 mediaptr 0x1000
Segment 1 load 00714660 size 819360 mediaptr 0x5dc660
Loading ramdisk 8720546 bytes @ 3f79d000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
[ 0.000000] Linux version 2.6.32 (cavok@ska) (gcc version 4.3.4 (GCC) ) #1 SMP Fri Dec 4 17:33:58 CET 2009
[ 0.000000] unwind_init: start = 0x405d8000, end = 0x4060b7c0, entries = 13180
[ 0.000000] WARNING: Out of order unwind entry! 00000000405da120 and 00000000405da130
[ 0.000000] WARNING: Out of order unwind entry! 00000000405da130 and 00000000405da140
[ 0.000000] FP[0] enabled: Rev 1 Model 16
[ 0.000000] The 64-bit Kernel has started...
[ 0.000000] bootconsole [ttyB0] enabled
[ 0.000000] Initialized PDC Console for debugging.
[ 0.000000] Determining PDC firmware type: System Map.
[ 0.000000] model 00005d10 00000491 00000000 00000002 77b406fc 100000f0 00000008 000000b2 000000b2
[ 0.000000] vers 00000300
[ 0.000000] CPUID vers 17 rev 10 (0x0000022a)
[ 0.000000] capabilities 0x3
[ 0.000000] model 9000/785/J5600
[ 0.000000] Total Memory: 3840 MB
[ 0.000000] LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
[ 0.000000] PERCPU: Embedded 10 pages/cpu @0000000044338000 s9984 r8192 d22784 u65536
[ 0.000000] pcpu-alloc: s9984 r8192 d22784 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] SMP: bootstrap CPU ID is 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 969600
[ 0.000000] Kernel command line: root=/dev/sda3 panic=60 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3856640k/3932160k available (4209k kernel code, 74972k reserved, 1735k data, 276k init)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] vmalloc : 0x0000000000008000 - 0x000000003f000000 (1007 MB)
[ 0.000000] memory : 0x0000000040000000 - 0x0000000130000000 (3840 MB)
[ 0.000000] .init : 0x0000000040798000 - 0x00000000407dd000 ( 276 kB)
[ 0.000000] .data : 0x000000004051c470 - 0x00000000406ce2a0 (1735 kB)
[ 0.000000] .text : 0x0000000040100000 - 0x000000004051c470 (4209 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 160x64
[ 0.060000] Calibrating delay loop... 1101.00 BogoMIPS (lpj=5505024)
[ 0.390000] Security Framework initialized
[ 0.450000] Mount-cache hash table entries: 256
[ 0.510000] Brought up 1 CPUs
[ 0.550000] NET: Registered protocol family 16
[ 0.610000] EISA bus registered
[ 0.650000] Searching for devices...
[ 0.960000] Found devices:
[ 0.990000] 1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582, 0x0000b }
[ 1.100000] 2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
[ 1.210000] 3. Elroy PCI Bridge at 0xfffffffffed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
[ 1.310000] 4. Elroy PCI Bridge at 0xfffffffffed34000 [10/2] { 13, 0x0, 0x782, 0x0000a }
[ 1.420000] 5. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
[ 1.530000] 6. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
[ 1.630000] 7. Forte W+ 2w at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5d1, 0x00004 }
[ 1.730000] 8. Forte W+ 2w at 0xfffffffffffa2000 [34] { 0, 0x0, 0x5d1, 0x00004 }
[ 1.830000] 9. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x09e, 0x00009 }
[ 2.040000] Releasing cpu 1 now, hpa=fffffffffffa2000
Service Menu: Enter command > pim hpmc
PROCESSOR PIM INFORMATION
----------------- Processor 0 HPMC Information ------------------
Timestamp =
Fri Dec 4 16:43:56 GMT 2009 (20:09:12:04:16:43:56)
HPMC Chassis Codes = 2cbf0 25008 2cbf4 2cbfc
General Registers 0 - 31
00-03 0000000000000000 0000000040795e40 00000000401170b4 0000000000000001
04-07 000000004076c640 0000000044349008 00000000406ef6b8 000000012f8a8140
08-11 0000000040675d1c 000000004062ddc0 0000000040675d68 00000000401210dc
12-15 0000000000000000 00000000406bb4b0 0000000000000001 00000000f0400004
16-19 000000004062e100 00000000407dbe80 00000000406bb4a8 0000000f32f63ff3
20-23 00000000000016f9 000000004062ddc0 0000000000000002 0000000000002710
24-27 00000000ffffffff 000000000800000e 0000000040648200 000000004076c640
28-31 0000000000004cd6 000000012f848e20 000000012f848af0 000000000000d7a0
<Press any key to continue (q to quit)>
Control Registers 0 - 31
00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000
04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
08-11 0000000000000000 0000000000000000 00000000000000c0 000000000000003e
12-15 0000000000000000 0000000000000000 0000000000103000 c000000000000000
16-19 0000000f32ff3d89 0000000000000000 0000000040117158 00000000020008bc
20-23 0000000000000000 0000000000000000 000000ff0804f90f 0000000000000000
24-27 00000000006d1000 00000000006d1000 0000000000044021 00000000f0412000
28-31 0000000055555555 0000000055555555 000000012f848000 0000000011111111
Space Registers 0 - 7
00-03 00000000 00000000 00000000 00000000
04-07 00000000 00000000 00000000 00000000
<Press any key to continue (q to quit)>
IIA Space = 0x0000000000000000
IIA Offset = 0x000000004011715c
Check Type = 0x20000000
CPU State = 0x9e000004
Cache Check = 0x00000000
TLB Check = 0x00000000
Bus Check = 0x0030000d
Assists Check = 0x00000000
Assist State = 0x00000000
Path Info = 0x00000000
System Responder Address = 0xfffffffffffa0000
System Requestor Address = 0xfffffffffffa2000
Floating-Point Registers 0 - 31
00-03 0000001f00000000 0000001f00000000 0000001f00000000 0000001f00000000
04-07 0000000000000000 5555555555555555 5555555555555555 5555555555555555
08-11 5555555555555555 5555555555555555 5555555555555555 5555555555555555
12-15 5555555555555555 5555555555555555 5555555555555555 5555555555555555
16-19 5555555555555555 5555555555555555 5555555555555555 5555555555555555
20-23 5555555555555555 5555555555555555 0000000000000000 0000000000000000
24-27 0000000000005000 0000000000000000 5555555555555555 5555555555555555
28-31 5555555555555555 5555555555555555 5555555555555555 5555555555555555
<Press any key to continue (q to quit)>
'9000/785 B,C,J Workstation Unarchitected (per-CPU)', rev 1, 140 bytes:
Check Summary = 0xcb81841000000000
Available Memory = 0x0000000100000000
CPU Diagnose Register 2 = 0x0300000000802004
CPU Status Register 0 = 0x3440c20000000000
CPU Status Register 1 = 0x8000000000000000
SADD LOG = 0x4820000000000000
Read Short LOG = 0xc18040fffee003fd
ERROR_STATUS = 0x0000000000000010
MEM_ADDR = 0x000001ff3fffffff
MEM_SYND = 0x0000000000000000
MEM_ADDR_CORR = 0x000001ff3fffffff
MEM_SYND_CORR = 0x0000000000000000
RUN_DATA_HIGH = 0x0ce0107fd89705f0
RUN_DATA_LOW = 0x73d73e81d2f91bf0
RUN_CTRL = 0x0000021c00001418
RUN_ADDR = 0xc13ff0f0f0039530
System Responder Path = 0x00ffffffffffffff
HPMC PIM Analysis Information:
Timestamp =
Fri Dec 4 16:43:56 GMT 2009 (20:09:12:04:16:43:56)
'9000/785 B,C,J Workstation HPMC PIM Analysis (per-CPU)', rev 0, 1304 bytes:
CPU 0 observed a Broadcast Error on the Runway Bus.
Memory/IO Controller Error Analysis Information:
The Memory/IO Controller only observed the Broadcast Error. It did not log
any additional information about the HPMC.
<Press any key to continue (q to quit)>
Memory Error Log Information:
Timestamp =
Fri Dec 4 16:43:56 GMT 2009 (20:09:12:04:16:43:56)
'9000/785 B,C,J Workstation Memory Error Log', rev 0, 64 bytes:
No memory errors logged
I/O Module Error Log Information:
Timestamp =
Fri Dec 4 16:43:56 GMT 2009 (20:09:12:04:16:43:56)
'9000/785 B,C,J Workstation IO Error Log', rev 0, 228 bytes:
Rope Word1 Word2 Word3
------ ------------ ------------
0 0x00000000 0x0e0cc009 0x00000000fed30048
1 0x00000000 0x1e0cc009 0x00000000fed32048
2 0x00000000 0x2e0cc009 0x00000000fed34048
3 ---------- 0x3e0cc009 ------------------
4 0x00000000 0x4e0cc009 0x00000000fed38048
5 ---------- 0x5e0cc009 ------------------
6 0x00000000 0x6e0cc009 0x00000000fed3c048
7 ---------- 0x7e0cc009 ------------------
Service Menu: Enter command >
