Dear Grant, Dear linux-parisc enthousiasts, Sorry for the late reply: in the last week, my vt220 terminal died and the power supply of my old (i386) server died as well, so I was busy with other things. I attached the "ser pim" output to this email, I hope it helps. If you need any other information, please ask, I hope I'll be more responsive next time... Dirk Grant Grundler wrote: > [ moved debian-hppa to BCC and added linux-parisc to CC ] > > On Fri, May 01, 2009 at 05:08:59PM +0200, Dirk Van Hertem wrote: >> hello, >> >> My hppa box (B2000) experiences some problems: it freezes after a few >> (2-6) hours. >> >> On the led display I get the following error codes: >> >> FLT CBFC: SYS BD >> bus timeout >> OS HPMC bz err >> Bad OS HPMC len >> HPMC initiated > > Hi Dirk, > Given the PCI listing you gave below, I agree the HPMC is likely caused by > the Promise SATA card. > >> I don't have screen nor keyboard attached to it so debugging is a bit >> difficult. > > AFAIK, the only way to debug this is to capture the HPMC dump. > The HPMC dump can only be capture via serial console. :( > (ie run "ser pim" at PDC prompt from a terminal emulator like minicom) > >> System: >> Debian lenny (stable), rather clean install >> >> $ uname -a >> Linux coulomb 2.6.26-2-parisc #1 Fri Mar 27 03:29:17 UTC 2009 parisc >> GNU/Linux >> >> >> The machines has the following lspci: >> >> 00:0c.0 Ethernet controller: Digital Equipment Corporation DECchip >> 21142/43 (rev 41) >> 00:0d.0 Multimedia audio controller: Analog Devices AD1889 sound chip >> 00:0e.0 IDE interface: National Semiconductor Corporation 87415/87560 >> IDE (rev 03) >> 00:0e.1 Bridge: National Semiconductor Corporation 87560 Legacy I/O (rev 01) >> 00:0e.2 USB Controller: National Semiconductor Corporation USB >> Controller (rev 02) >> 00:0f.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895a (rev 01) >> 01:00.0 3D controller: Hewlett-Packard Company Visualize FXe (rev 03) >> 01:04.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA >> 300 TX4) (rev 02) >> >> Of which the last entry might well be the problem. >> >> This is a promise card for my 3* 1TB sata disks. They seem to be >> initialized correctly, I made software raid with mdadm, but not I get >> the following: >> >> $ cat /proc/mdstat >> Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] >> [raid4] [raid10] >> md0 : active raid5 sdc1[0] sde1[3] sdd1[1] >> 1953519872 blocks level 5, 64k chunk, algorithm 2 [3/2] [UU_] >> [=>...................] recovery = 5.8% (56795292/976759936) >> finish=451.9min speed=33920K/sec >> >> unused devices: <none> >> >> This keeps on running for a few hours, until the machine gets unresponsive. >> >> I don't think I get anything strange in syslog, kernel.log, messages,... >> >> So, my questions: >> * Is this sata promise card the fault? > > Likely, yes. > >> * on the web, the errors on the display seemed to indicate hardware >> problems, but any insight on that? > > HW caught the error. Unless this happens w/o Promise care present, > I'm not inclined to believe this is a HW problem. > >> * Best ways to solve this? > > Capture "ser pim" output (aka PIM dump). > >> * Did I forget something? >> >> Dirk >> >> PS: Next thing I'll try is to remove the promise card to see if that was >> the problem >> PPS: dmesg in attach > > thanks! > grant > >> -- >> Dirk Van Hertem Dirk.VanHertem@xxxxxxxxxxxxxxxx >> Electrical Engineering Department http://www.esat.kuleuven.be/electa >> K.U. Leuven, ESAT-ELECTA tel: +32-16-32.18.95 >> 10, Kasteelpark Arenberg, B-3001 Heverlee fax: +32-16-32.19.85 > >> [ 0.000000] Initializing cgroup subsys cpu >> [ 0.000000] Linux version 2.6.26-2-parisc (Debian 2.6.26-15) (dannf@xxxxxxxxxx) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Fri Mar 27 03:29:17 UTC 2009 >> [ 0.000000] FP[0] enabled: Rev 1 Model 16 >> [ 0.000000] The 32-bit Kernel has started... >> [ 0.000000] console [ttyB0] enabled >> [ 0.000000] Initialized PDC Console for debugging. >> [ 0.000000] Determining PDC firmware type: System Map. >> [ 0.000000] model 00005d00 00000481 00000000 00000002 782d3480 100000f0 00000008 000000b2 000000b2 >> [ 0.000000] vers 00000301 >> [ 0.000000] CPUID vers 17 rev 11 (0x0000022b) >> [ 0.000000] capabilities 0x3 >> [ 0.000000] model 9000/785/B2000 >> [ 0.000000] Total Memory: 1024 MB >> [ 0.000000] initrd: 4f8ce000-4ffedfb5 >> [ 0.000000] initrd: reserving 3f8ce000-3ffedfb5 (mem_max 40000000) >> [ 0.000000] On node 0 totalpages: 262144 >> [ 0.000000] Normal zone: 2048 pages used for memmap >> [ 0.000000] Normal zone: 0 pages reserved >> [ 0.000000] Normal zone: 260096 pages, LIFO batch:31 >> [ 0.000000] Movable zone: 0 pages used for memmap >> [ 0.000000] LCD display at f05d0008,f05d0000 registered >> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 >> [ 0.000000] Kernel command line: root=/dev/sdb5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux >> [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) >> [17179569.184000] Console: colour dummy device 160x64 >> [17179569.248000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >> [17179569.348000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >> [17179569.532000] Memory: 1026560k/1048576k available (1961k kernel code, 21792k reserved, 882k data, 224k init) >> [17179569.660000] virtual kernel memory layout: >> [17179569.660000] vmalloc : 0x00008000 - 0x0f000000 ( 239 MB) >> [17179569.660000] memory : 0x10000000 - 0x50000000 (1024 MB) >> [17179569.660000] .init : 0x10410000 - 0x10448000 ( 224 kB) >> [17179569.660000] .data : 0x102ea6b4 - 0x103c7000 ( 882 kB) >> [17179569.660000] .text : 0x10100000 - 0x102ea6b4 (1961 kB) >> [17179570.112000] Calibrating delay loop... 798.72 BogoMIPS (lpj=1597440) >> [17179570.204000] Security Framework initialized >> [17179570.260000] SELinux: Disabled at boot. >> [17179570.312000] Capability LSM initialized >> [17179570.368000] Mount-cache hash table entries: 512 >> [17179570.428000] Initializing cgroup subsys ns >> [17179570.484000] Initializing cgroup subsys cpuacct >> [17179570.548000] Initializing cgroup subsys devices >> [17179570.612000] net_namespace: 648 bytes >> [17179570.660000] NET: Registered protocol family 16 >> [17179570.724000] EISA bus registered >> [17179570.768000] Searching for devices... >> [17179571.020000] Found devices: >> [17179571.060000] 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } >> [17179571.160000] 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } >> [17179571.264000] 3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } >> [17179571.364000] 4. Kazoo W+ at 0xfffa0000 [32] { 0, 0x0, 0x5d0, 0x00004 } >> [17179571.452000] 5. Memory at 0xfed10200 [49] { 1, 0x0, 0x09d, 0x00009 } >> [17179571.536000] Enabling regular chassis codes support v0.05 >> [17179571.736000] CPU(s): 1 x PA8600 (PCX-W+) at 400.000000 MHz >> [17179571.812000] Whole cache flush 115727 cycles, flushing 3440640 bytes 467519 cycles >> [17179571.812000] Setting cache flush threshold to 1980 (1 CPUs online) >> [17179571.920000] SBA found Astro 2.1 at 0xfed00000 >> [17179571.984000] Elroy version TR4.0 (0x5) found at 0xfed30000 >> [17179572.060000] PCI: Enabled native mode for NS87415 (pif=0x8f) >> [17179572.140000] Elroy version TR4.0 (0x5) found at 0xfed32000 >> [17179572.232000] powersw: Soft power switch at 0xf0400804 enabled. >> [17179572.324000] NET: Registered protocol family 2 >> [17179572.424000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) >> [17179572.520000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) >> [17179572.624000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) >> [17179572.716000] TCP: Hash tables configured (established 131072 bind 65536) >> [17179572.808000] TCP reno registered >> [17179572.864000] NET: Registered protocol family 1 >> [17179572.924000] checking if image is initramfs... it is >> [17179575.908000] Freeing initrd memory: 7295k freed >> [17179575.976000] Enabling PDC chassis warnings support v0.05 >> [17179576.048000] unwind_init: start = 0x1035de10, end = 0x103850f0, entries = 10030 >> [17179576.144000] WARNING: Out of order unwind entry! 1035f810 and 1035f820 >> [17179576.232000] WARNING: Out of order unwind entry! 1035f820 and 1035f830 >> [17179576.324000] audit: initializing netlink socket (disabled) >> [17179576.396000] type=2000 audit(1241188257.212:1): initialized >> [17179576.472000] VFS: Disk quotas dquot_6.5.1 >> [17179576.528000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> [17179576.620000] msgmni has been set to 2019 >> [17179576.676000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) >> [17179576.776000] io scheduler noop registered >> [17179576.832000] io scheduler anticipatory registered >> [17179576.896000] io scheduler deadline registered >> [17179576.956000] io scheduler cfq registered (default) >> [17179577.020000] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67) >> [17179577.120000] SuperIO: Serial port 1 at 0x3f8 >> [17179577.176000] SuperIO: Serial port 2 at 0x2f8 >> [17179577.236000] SuperIO: Parallel port at 0x378 >> [17179577.292000] SuperIO: Floppy controller at 0x3f0 >> [17179577.356000] SuperIO: ACPI at 0x7e0 >> [17179577.404000] SuperIO: USB regulator enabled >> [17179577.464000] PDC Stable Storage facility v0.30 >> [17179577.836000] STI GSC/PCI core graphics driver Version 0.9a >> [17179577.912000] sti 0000:01:00.0: enabling SERR and PARITY (0046 -> 0146) >> [17179578.000000] STI PCI graphic ROM found at f4840000 (128 kB), fb at fb000000 (16 MB) >> [17179578.228000] id 35acda16-9a02587, conforms to spec rev. 8.0c >> [17179578.312000] graphics card name: HPA4982A >> [17179578.368000] sticon: Initializing STI text console. >> [17179578.436000] Console: switching to colour STI console 160x64 >> [17179578.788000] stifb: 'HPA4982A' (id: 0x35acda16) not supported. >> [17179578.876000] Generic RTC Driver v1.07 >> [17179578.928000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled >> [17179579.036000] serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A >> [17179579.116000] console handover: boot [ttyB0] -> real [ttyS0] >> [17179579.192000] serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A >> [17179579.276000] brd: module loaded >> [17179579.316000] mice: PS/2 mouse device common for all mice >> [17179579.384000] TCP cubic registered >> [17179579.424000] NET: Registered protocol family 17 >> [17179579.484000] registered taskstats version 1 >> [17179579.536000] Freeing unused kernel memory: 224k freed >> [17179580.348000] SCSI subsystem initialized >> [17179581.996000] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007) >> [17179582.080000] tulip0: no phy info, aborting mtable build >> [17179582.144000] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1. >> [17179582.248000] eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xf4005000, 00:30:6e:08:0a:7f, IRQ 65. >> [17179582.544000] usbcore: registered new interface driver usbfs >> [17179582.612000] usbcore: registered new interface driver hub >> [17179582.704000] sym0: <895a> rev 0x1 at pci 0000:00:0f.0 irq 68 >> [17179582.804000] libata version 3.00 loaded. >> [17179582.824000] sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking >> [17179582.904000] sym0: SCSI BUS has been reset. >> [17179582.964000] scsi0 : sym-2.2.3 >> [17179583.008000] usbcore: registered new device driver usb >> [17179583.096000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver >> [17179583.096000] ohci_hcd: block sizes: ed 64 td 64 >> [17179583.100000] ohci_hcd 0000:00:0e.2: OHCI Host Controller >> [17179583.168000] ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 >> [17179583.260000] ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup >> [17179583.260000] ohci_hcd 0000:00:0e.2: created debug files >> [17179583.260000] ohci_hcd 0000:00:0e.2: irq 1, io mem 0xf4004000 >> [17179583.384000] ohci_hcd 0000:00:0e.2: OHCI controller state >> [17179583.384000] ohci_hcd 0000:00:0e.2: OHCI 1.0, NO legacy support registers >> [17179583.384000] ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3 >> [17179583.384000] ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0 >> [17179583.384000] ohci_hcd 0000:00:0e.2: intrstatus 0x00000000 >> [17179583.384000] ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH >> [17179583.384000] ohci_hcd 0000:00:0e.2: hcca frame #0000 >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3(3) >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000 >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS >> [17179583.384000] ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS >> [17179583.384000] usb usb1: default language 0x0409 >> [17179583.384000] usb usb1: uevent >> [17179583.384000] usb usb1: usb_probe_device >> [17179583.384000] usb usb1: configuration #1 chosen from 1 choice >> [17179583.452000] usb usb1: adding 1-0:1.0 (config #1, interface 0) >> [17179583.452000] usb 1-0:1.0: uevent >> [17179583.452000] hub 1-0:1.0: usb_probe_interface >> [17179583.452000] hub 1-0:1.0: usb_probe_interface - got id >> [17179583.452000] hub 1-0:1.0: USB hub found >> [17179583.500000] hub 1-0:1.0: 3 ports detected >> [17179583.552000] hub 1-0:1.0: standalone hub >> [17179583.552000] hub 1-0:1.0: ganged power switching >> [17179583.552000] hub 1-0:1.0: no over-current protection >> [17179583.552000] hub 1-0:1.0: power on to power good time: 0ms >> [17179583.552000] hub 1-0:1.0: local power source is good >> [17179583.552000] hub 1-0:1.0: enabling power on all ports >> [17179583.656000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 >> [17179583.740000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >> [17179583.828000] usb usb1: Product: OHCI Host Controller >> [17179583.892000] usb usb1: Manufacturer: Linux 2.6.26-2-parisc ohci_hcd >> [17179583.968000] usb usb1: SerialNumber: 0000:00:0e.2 >> [17179584.032000] sata_promise 0000:01:04.0: version 2.12 >> [17179584.032000] scsi1 : sata_promise >> [17179584.112000] Uniform Multi-Platform E-IDE driver >> [17179584.168000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx >> [17179584.268000] scsi2 : sata_promise >> [17179584.312000] scsi3 : sata_promise >> [17179584.352000] scsi4 : sata_promise >> [17179584.396000] ata1: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820380 irq 70 >> [17179584.484000] ata2: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820280 irq 70 >> [17179584.576000] ata3: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820200 irq 70 >> [17179584.668000] ata4: SATA max UDMA/133 mmio m4096@0xf4820000 ata 0xf4820300 irq 70 >> [17179584.760000] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000 >> [17179584.792000] NS87415: IDE controller (0x100b:0x0002 rev 0x03) at PCI slot 0000:00:0e.0 >> [17179584.892000] NS87415: 100% native mode on irq 7 >> [17179584.948000] ide0: BM-DMA at 0x0900-0x0907 >> [17179585.008000] ide1: BM-DMA at 0x0908-0x090f >> [17179585.060000] Probing IDE interface ide0... >> [17179585.184000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [17179585.284000] ata1.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133 >> [17179585.368000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) >> [17179585.468000] ata1.00: configured for UDMA/133 >> [17179585.692000] hda: FX4830T, ATAPI CD/DVD-ROM drive >> [17179585.856000] ata2: SATA link down (SStatus 0 SControl 300) >> [17179586.240000] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [17179586.340000] ata3.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133 >> [17179586.424000] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) >> [17179586.524000] ata3.00: configured for UDMA/133 >> [17179586.692000] Probing IDE interface ide1... >> [17179586.896000] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) >> [17179586.996000] ata4.00: ATA-8: Hitachi HDT721010SLA360, ST6OA31B, max UDMA/133 >> [17179587.080000] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) >> [17179587.180000] ata4.00: configured for UDMA/133 >> [17179587.232000] scsi: waiting for bus probes to complete ... >> [17179587.524000] ide0 at 0xe00-0xe07,0xd02 on irq 7 >> [17179587.580000] ide1 at 0xb00-0xb07,0xa02 on irq 7 >> [17179587.636000] scsi 0:0:5:0: Direct-Access IBM IC35L073UCDY10-0 S27T PQ: 0 ANSI: 3 >> [17179587.736000] target0:0:5: tagged command queuing enabled, command queue depth 16. >> [17179587.828000] target0:0:5: Beginning Domain Validation >> [17179587.892000] target0:0:5: asynchronous >> [17179587.944000] target0:0:5: wide asynchronous >> [17179587.996000] target0:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) >> [17179588.084000] target0:0:5: Domain Validation skipping write tests >> [17179588.160000] target0:0:5: Ending Domain Validation >> [17179588.220000] scsi 0:0:6:0: Direct-Access QUANTUM ATLAS5-9LVD HP04 PQ: 0 ANSI: 3 >> [17179588.320000] target0:0:6: tagged command queuing enabled, command queue depth 16. >> [17179588.412000] target0:0:6: Beginning Domain Validation >> [17179588.476000] target0:0:6: asynchronous >> [17179588.528000] target0:0:6: wide asynchronous >> [17179588.580000] target0:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) >> [17179588.668000] target0:0:6: Domain Validation skipping write tests >> [17179588.744000] target0:0:6: Ending Domain Validation >> [17179591.132000] scsi 1:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5 >> [17179591.304000] scsi 3:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5 >> [17179591.440000] Driver 'sd' needs updating - please use bus_type methods >> [17179591.608000] scsi 4:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5 >> [17179591.732000] sd 0:0:5:0: [sda] 143374650 512-byte hardware sectors (73408 MB) >> [17179592.108000] sd 0:0:5:0: [sda] Write Protect is off >> [17179592.168000] sd 0:0:5:0: [sda] Mode Sense: cb 00 00 08 >> [17179592.296000] hda: ATAPI 48X CD-ROM drive, 128kB Cache >> [17179592.356000] Uniform CD-ROM driver Revision: 3.20 >> [17179592.524000] sd 0:0:5:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA >> [17179592.640000] sd 0:0:5:0: [sda] 143374650 512-byte hardware sectors (73408 MB) >> [17179592.728000] sd 0:0:5:0: [sda] Write Protect is off >> [17179592.788000] sd 0:0:5:0: [sda] Mode Sense: cb 00 00 08 >> [17179592.788000] sd 0:0:5:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA >> [17179592.904000] sda: sda1 >> [17179592.964000] sd 0:0:5:0: [sda] Attached SCSI disk >> [17179593.044000] sd 0:0:6:0: [sdb] 17773524 512-byte hardware sectors (9100 MB) >> [17179593.140000] sd 0:0:6:0: [sdb] Write Protect is off >> [17179593.204000] sd 0:0:6:0: [sdb] Mode Sense: e3 00 10 08 >> [17179593.232000] sd 0:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA >> [17179593.348000] sd 0:0:6:0: [sdb] 17773524 512-byte hardware sectors (9100 MB) >> [17179593.432000] sd 0:0:6:0: [sdb] Write Protect is off >> [17179593.496000] sd 0:0:6:0: [sdb] Mode Sense: e3 00 10 08 >> [17179593.496000] sd 0:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA >> [17179593.600000] sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 > sdb4 >> [17179593.724000] sd 0:0:6:0: [sdb] Attached SCSI disk >> [17179593.792000] sd 1:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179593.884000] sd 1:0:0:0: [sdc] Write Protect is off >> [17179593.944000] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00 >> [17179593.944000] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179594.056000] sd 1:0:0:0: [sdc] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179594.148000] sd 1:0:0:0: [sdc] Write Protect is off >> [17179594.208000] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00 >> [17179594.208000] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179594.320000] sdc: sdc1 >> [17179594.364000] sd 1:0:0:0: [sdc] Attached SCSI disk >> [17179594.432000] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179594.520000] sd 3:0:0:0: [sdd] Write Protect is off >> [17179594.584000] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 >> [17179594.584000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179594.696000] sd 3:0:0:0: [sdd] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179594.784000] sd 3:0:0:0: [sdd] Write Protect is off >> [17179594.844000] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 >> [17179594.844000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179594.956000] sdd: sdd1 >> [17179595.004000] sd 3:0:0:0: [sdd] Attached SCSI disk >> [17179595.068000] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179595.160000] sd 4:0:0:0: [sde] Write Protect is off >> [17179595.220000] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00 >> [17179595.220000] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179595.332000] sd 4:0:0:0: [sde] 1953525168 512-byte hardware sectors (1000205 MB) >> [17179595.424000] sd 4:0:0:0: [sde] Write Protect is off >> [17179595.484000] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00 >> [17179595.484000] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >> [17179595.596000] sde: sde1 >> [17179595.640000] sd 4:0:0:0: [sde] Attached SCSI disk >> [17179596.980000] md: linear personality registered for level -1 >> [17179597.088000] md: multipath personality registered for level -4 >> [17179597.200000] md: raid0 personality registered for level 0 >> [17179597.312000] md: raid1 personality registered for level 1 >> [17179597.416000] xor: measuring software checksum speed >> [17179597.496000] 8regs : 943.000 MB/sec >> [17179597.568000] 8regs_prefetch: 933.000 MB/sec >> [17179597.644000] 32regs : 960.000 MB/sec >> [17179597.716000] 32regs_prefetch: 945.000 MB/sec >> [17179597.772000] xor: using function: 32regs (960.000 MB/sec) >> [17179597.848000] async_tx: api initialized (sync-only) >> [17179598.012000] raid6: int32x1 183 MB/s >> [17179598.128000] raid6: int32x2 230 MB/s >> [17179598.244000] raid6: int32x4 272 MB/s >> [17179598.360000] raid6: int32x8 213 MB/s >> [17179598.408000] raid6: using algorithm int32x4 (272 MB/s) >> [17179598.468000] md: raid6 personality registered for level 6 >> [17179598.536000] md: raid5 personality registered for level 5 >> [17179598.604000] md: raid4 personality registered for level 4 >> [17179598.896000] md: raid10 personality registered for level 10 >> [17179599.136000] md: bind<sdd1> >> [17179599.172000] md: bind<sde1> >> [17179599.208000] md: bind<sdc1> >> [17179599.324000] raid5: device sdc1 operational as raid disk 0 >> [17179599.392000] raid5: device sdd1 operational as raid disk 1 >> [17179599.460000] raid5: allocated 3176kB for md0 >> [17179599.512000] raid5: raid level 5 set md0 active with 2 out of 3 devices, algorithm 2 >> [17179599.608000] RAID5 conf printout: >> [17179599.648000] --- rd:3 wd:2 >> [17179599.684000] disk 0, o:1, dev:sdc1 >> [17179599.728000] disk 1, o:1, dev:sdd1 >> [17179600.672000] EXT3-fs: INFO: recovery required on readonly filesystem. >> [17179600.752000] EXT3-fs: write access will be enabled during recovery. >> [17179601.128000] kjournald starting. Commit interval 5 seconds >> [17179601.196000] EXT3-fs: recovery complete. >> [17179601.244000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179603.920000] udevd version 125 started >> [17179604.124000] usb usb1: uevent >> [17179604.124000] usb 1-0:1.0: uevent >> [17179609.280000] Adding 489940k swap on /dev/sdb7. Priority:-1 extents:1 across:489940k >> [17179609.764000] EXT3 FS on sdb5, internal journal >> [17179610.860000] LASI 82596 driver - Revision: 1.30 >> [17179610.980000] loop: module loaded >> [17179616.900000] RAID5 conf printout: >> [17179616.944000] --- rd:3 wd:2 >> [17179616.980000] disk 0, o:1, dev:sdc1 >> [17179617.024000] disk 1, o:1, dev:sdd1 >> [17179617.072000] disk 2, o:1, dev:sde1 >> [17179617.116000] md: recovery of RAID array md0 >> [17179617.168000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. >> [17179617.240000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. >> [17179617.360000] md: using 128k window, over a total of 976759936 blocks. >> [17179632.056000] kjournald starting. Commit interval 5 seconds >> [17179632.140000] EXT3 FS on sdb8, internal journal >> [17179632.196000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179632.312000] kjournald starting. Commit interval 5 seconds >> [17179632.392000] EXT3 FS on sdb4, internal journal >> [17179632.448000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179632.556000] kjournald starting. Commit interval 5 seconds >> [17179632.632000] EXT3 FS on sdb6, internal journal >> [17179632.688000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179632.816000] kjournald starting. Commit interval 5 seconds >> [17179632.920000] EXT3 FS on sda1, internal journal >> [17179632.976000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179633.408000] kjournald starting. Commit interval 5 seconds >> [17179633.512000] EXT3 FS on md0, internal journal >> [17179633.564000] EXT3-fs: mounted filesystem with ordered data mode. >> [17179639.712000] eth0: Setting full-duplex based on MII#1 link partner capability of 45e1. > > -- Dirk Van Hertem Dirk.VanHertem@xxxxxxxxxxxxxxxx Electrical Engineering Department http://www.esat.kuleuven.be/electa K.U. Leuven, ESAT-ELECTA tel: +32-16-32.18.95 10, Kasteelpark Arenberg, B-3001 Heverlee fax: +32-16-32.19.85
Main Menu: Enter command > ser pim PROCESSOR PIM INFORMATION ----------------- Processor 0 HPMC Information ------------------ Timestamp = Fri May 15 20:19:22 GMT 2009 (20:09:05:15:20:19:22) HPMC Chassis Codes = 2cbf0 2500b 2cbf2 2cbfc General Registers 0 - 31 00-03 0000000000000000 000000001021d000 00000000000fca38 000000004df4c074 04-07 0000000000000000 000000004df4d380 000000000008073c 000000004df4c000 08-11 0000000000102598 0000000000013000 0000000000000000 0000000000013000 12-15 0000000000000000 0000000000000005 00000000001ca06c 00000000f0400004 16-19 000000004e1f8540 00000000f000017c 00000000f0000174 000000004df4c000 20-23 0000000000000001 0000000000066004 0000000000066000 000000004f497b30 24-27 0000000000000001 ffffffff80000000 000000004df4c074 00000000103850f0 28-31 0000000001000000 0000000000066380 000000004e1f8bc0 0000000000000004 <Press any key to continue (q to quit)> Control Registers 0 - 31 00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000 04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000 08-11 000000000000003a 0000000000000000 00000000000000c0 0000000000000001 12-15 0000000000000000 0000000000000000 000000000010d000 00000000fe000000 16-19 000002aeeacf3b1a 0000000000000000 0000000000070464 000000000ff6009c 20-23 00000000a627ffd2 0000000008066004 000000ff0004ff0e 0000000080000000 24-27 00000000003c7000 000000003e402000 0000000000044021 00000000f0412000 28-31 0000000055555555 0000000055555555 000000004e1f8000 0000000011111111 Space Registers 0 - 7 00-03 00000000 00000000 00000000 0000001d 04-07 00000000 00000000 00000000 00000000 <Press any key to continue (q to quit)> IIA Space = 0x0000000000000000 IIA Offset = 0x0000000000070468 Check Type = 0x20000000 CPU State = 0x9e000004 Cache Check = 0x00000000 TLB Check = 0x00000000 Bus Check = 0x0030103b Assists Check = 0x00000000 Assist State = 0x00000000 Path Info = 0x00000000 System Responder Address = 0x000000fff4820004 System Requestor Address = 0xfffffffffffa0000 Floating-Point Registers 0 - 31 00-03 0000001f00000000 0000000000000000 0000000000000000 0000000000000000 04-07 7ff7ffffffffffff 41d25c49fb800000 000000058c000000 7ff7ffffffffffff 08-11 000000000000fe9c 000000024f415bc0 4f415bc800000000 1056c58000000003 12-15 5555555555555555 5555555555555555 5555555555555555 5555555555555555 16-19 5555555555555555 5555555555555555 5555555555555555 5555555555555555 20-23 5555555555555555 5555555555555555 0000008099999e4f 003a2c6a00000000 24-27 0000000000000000 000000001d163500 00001c3e103d2b48 1022b1c810263260 28-31 ffffffff00001c3e 103990b01018c6ec 103990b000000190 4f42428010115ed0 <Press any key to continue (q to quit)> '9000/785 B,C,J Workstation Unarchitected (per-CPU)', rev 1, 140 bytes: Check Summary = 0xcb81041008000000 Available Memory = 0x0000000040000000 CPU Diagnose Register 2 = 0x0301000000000004 CPU Status Register 0 = 0x2420c20000000000 CPU Status Register 1 = 0x8002000000000000 SADD LOG = 0xc100f0fff4820004 Read Short LOG = 0xc1a0f0fff4820004 ERROR_STATUS = 0x0000000000100010 MEM_ADDR = 0x000001ff3fffffff MEM_SYND = 0x0000000000000000 MEM_ADDR_CORR = 0x000001ff3fffffff MEM_SYND_CORR = 0x0000000000000000 RUN_DATA_HIGH = 0xc1bff0fffed08040 RUN_DATA_LOW = 0xc1bff0fffed08040 RUN_CTRL = 0x0000021c00001418 RUN_ADDR = 0xc1bff0fffed08040 System Responder Path = 0x00ffffff0a010400 HPMC PIM Analysis Information: Timestamp = Fri May 15 20:19:22 GMT 2009 (20:09:05:15:20:19:22) '9000/785 B,C,J Workstation HPMC PIM Analysis (per-CPU)', rev 0, 1304 bytes: A Data I/O Fetch Timeout occurred while CPU 0 was requesting information from a device at the path 10/1/4/0 (PCI slot 4). Memory/IO Controller Error Analysis Information: The Memory/IO Controller only observed the Broadcast Error. It did not log any additional information about the HPMC. <Press any key to continue (q to quit)> ----------------- Processor 0 LPMC Information ------------------ Check Type = 0x00000000 I/D Cache Parity Info = 0x00000000 Cache Check = 0x00000000 TLB Check = 0x00000000 Bus Check = 0x00000000 Assists Check = 0x00000000 Assist State = 0x00000000 Path Info = 0x00000000 System Responder Address = 0x0000000000000000 System Requestor Address = 0x0000000000000000 ----------------- Processor 0 TOC Information ------------------- General Registers 0 - 31 00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000 04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000 08-11 0000000000000000 0000000000000000 0000000000000000 0000000000000000 12-15 0000000000000000 0000000000000000 0000000000000000 0000000000000000 16-19 0000000000000000 0000000000000000 0000000000000000 0000000000000000 20-23 0000000000000000 0000000000000000 0000000000000000 0000000000000000 24-27 0000000000000000 0000000000000000 0000000000000000 0000000000000000 28-31 0000000000000000 0000000000000000 0000000000000000 0000000000000000 <Press any key to continue (q to quit)> <Press any key to continue (q to quit)> Control Registers 0 - 31 00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000 04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000 08-11 0000000000000000 0000000000000000 0000000000000000 0000000000000000 12-15 0000000000000000 0000000000000000 0000000000000000 0000000000000000 16-19 0000000000000000 0000000000000000 0000000000000000 0000000000000000 20-23 0000000000000000 0000000000000000 0000000000000000 0000000000000000 24-27 0000000000000000 0000000000000000 0000000000000000 0000000000000000 28-31 0000000000000000 0000000000000000 0000000000000000 0000000000000000 Space Registers 0 - 7 00-03 00000000 00000000 00000000 00000000 04-07 00000000 00000000 00000000 00000000 IIA Space = 0x0000000000000000 IIA Offset = 0x0000000000000000 CPU State = 0x00000000 <Press any key to continue (q to quit)> Memory Error Log Information: Timestamp = Fri May 15 20:19:22 GMT 2009 (20:09:05:15:20:19:22) '9000/785 B,C,J Workstation Memory Error Log', rev 0, 64 bytes: No memory errors logged I/O Module Error Log Information: Timestamp = Fri May 15 20:19:22 GMT 2009 (20:09:05:15:20:19:22) '9000/785 B,C,J Workstation IO Error Log', rev 0, 228 bytes: Rope Word1 Word2 Word3 ------ ------------ ------------ 0 0x00000000 0x0e0cc009 0x00000000fed30048 1 ---------- 0x1e0cc2a9 ------------------ 2 ---------- 0x2e0cc009 ------------------ 3 ---------- 0x3e0cc009 ------------------ 4 ---------- 0x4e0cc009 ------------------ 5 ---------- 0x5e0cc009 ------------------ 6 ---------- 0x6e0cc009 ------------------ 7 ---------- 0x7e0cc009 ------------------ Main Menu: Enter command >
