On Tue, 2008-05-06 at 22:17 +0100, Mel Gorman wrote: > On (06/05/08 14:58), James Bottomley didst pronounce: > > On Tue, 2008-05-06 at 16:27 +0100, Mel Gorman wrote: > > > On (06/05/08 16:46), Adrian Bunk didst pronounce: > > > > Commit 54a6eb5c4765aa573a030ceeba2c14e3d2ea5706 > > > > (mm: use two zonelist that are filtered by GFP mask) > > > > causes the following build error with CONFIG_DISCONTIGMEM=y > > > > on parisc: > > > > > > > > > > Thanks Adrian. I don't have a pa-risc cross-compiler and there isn't one > > > at the usual source http://userweb.kernel.org/~akpm/cross-compilers but the > > > patch below should fix it. Note that this debugging code should be deleted if > > > the mm-initialisation-and-debugging framework in -mm is merged to mainline > > > as it knows how to print all the zonelists where as the pa-risc equivilant > > > misses the GFP_THISNODE lists. > > > > > > ===== > > > Subject: [PATCH] Fix pa-risc DISCONTIGMEM compile breakage > > > > > > PA-RISC to aid debugging prints out the zonelists setup by the system. A > > > bad call to node_zonelist() breaks at compile-time. This patch fixes it. > > > > > > Signed-off-by: Mel Gorman <mel@xxxxxxxxx> > > > --- > > > arch/parisc/mm/init.c | 2 +- > > > 1 file changed, 1 insertion(+), 1 deletion(-) > > > > > > diff --git a/arch/parisc/mm/init.c b/arch/parisc/mm/init.c > > > index 1f01284..b0ed709 100644 > > > --- a/arch/parisc/mm/init.c > > > +++ b/arch/parisc/mm/init.c > > > @@ -606,7 +606,7 @@ void show_mem(void) > > > int i, j; > > > > > > for (i = 0; i < npmem_ranges; i++) { > > > - zl = node_zonelist(i); > > > + zl = node_zonelist(i, 0); > > > for (j = 0; j < MAX_NR_ZONES; j++) { > > > > This rather doesn't look right. The intent is for i to iterate over the > > ranges (as nodes) and j to iterate over the zones to get the zonelist. > > Yes, that appears to be the original intention. > > > The original variable k was going over the mappings, which you replaced > > with for_each_zone_zonelist. If you use node_zonelist(i, 0) you don't > > really look at the actual zones in the map. > > > > No, but you filter the one list based on the highest zone that can be > accesssed. > > > Therefore it seems what will give the original functionality back is > > actually this: > > > > To be fair, a few weeks ago you would have been right. Since then zonelists > have changed though so that there are only two zonelists per node in > git-latest. One which is for general allocations and one for GFP_THISNODE. The > zonelist is filtered based on the GFP flags, hence the iterator. I copied the > parisc code with the compile-fix into mm/page_alloc.c and called it just to > be sure and with qemu, I see > > [ 0.628960] Zone list for zone 0 on node 0: [0/DMA] > [ 0.628960] Zone list for zone 1 on node 0: [0/Normal] [0/DMA] > [ 0.628960] Zone list for zone 2 on node 0: [0/HighMem] [0/Normal] [0/DMA] > [ 0.628960] Zone list for zone 3 on node 0: [0/Movable] [0/HighMem] [0/Normal] [0/DMA] > > which looks right (movablecore was specified hence the existance of the > movable zone). Thanks ... I confirmed that your fix does actually work. Mysteriously, this is what it produces as output: Zone list for zone 0 on node 0: [0/Normal] [0/Normal] Zone list for zone 1 on node 0: [0/Normal] [0/Normal] Zone list for zone 0 on node 1: [0/Normal] [0/Normal] Zone list for zone 1 on node 1: [0/Normal] [0/Normal] Which is correct James -- To unsubscribe from this list: send the line "unsubscribe linux-parisc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
