[PATCH v11 10/10] mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



With OMAP NAND driver updates, selection of ecc-scheme:
*DT enabled kernel*
 	depends on ti,nand-ecc-opt and ti,elm-id DT bindings.
*Non DT enabled kernel*
	depends on elm_dev and ecc-scheme passed along with platform-data
	from board file.

So, selection of ecc-scheme (BCH8 or BCH4) from KConfig can be removed

Signed-off-by: Pekon Gupta <pekon@xxxxxx>
---
 drivers/mtd/nand/Kconfig | 40 ++++++----------------------------------
 1 file changed, 6 insertions(+), 34 deletions(-)

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index d885298..93ae6a6 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -96,43 +96,15 @@ config MTD_NAND_OMAP2
 
 config MTD_NAND_OMAP_BCH
 	depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3
-	tristate "Enable support for hardware BCH error correction"
+	tristate "Support hardware based BCH error correction"
 	default n
 	select BCH
-	select BCH_CONST_PARAMS
 	help
-	 Support for hardware BCH error correction.
-
-choice
-	prompt "BCH error correction capability"
-	depends on MTD_NAND_OMAP_BCH
-
-config MTD_NAND_OMAP_BCH8
-	bool "8 bits / 512 bytes (recommended)"
-	help
-	 Support correcting up to 8 bitflips per 512-byte block.
-	 This will use 13 bytes of spare area per 512 bytes of page data.
-	 This is the recommended mode, as 4-bit mode does not work
-	 on some OMAP3 revisions, due to a hardware bug.
-
-config MTD_NAND_OMAP_BCH4
-	bool "4 bits / 512 bytes"
-	help
-	 Support correcting up to 4 bitflips per 512-byte block.
-	 This will use 7 bytes of spare area per 512 bytes of page data.
-	 Note that this mode does not work on some OMAP3 revisions, due to a
-	 hardware bug. Please check your OMAP datasheet before selecting this
-	 mode.
-
-endchoice
-
-if MTD_NAND_OMAP_BCH
-config BCH_CONST_M
-	default 13
-config BCH_CONST_T
-	default 4 if MTD_NAND_OMAP_BCH4
-	default 8 if MTD_NAND_OMAP_BCH8
-endif
+	  This config enables the ELM hardware engine, which can be used to
+	  locate and correct errors when using BCH ECC scheme. This offloads
+	  the cpu from doing ECC error searching and correction. However some
+	  legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
+	  so they should not enable this config symbol.
 
 config MTD_NAND_IDS
 	tristate
-- 
1.8.1

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux