Re: [RFCv2 3/3] ARM: dts: N900: Add SSI information

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 09/15/2013 02:44 PM, Sebastian Reichel wrote:
> Add SSI device tree data for OMAP34xx and Nokia N900.

What is an "SSI" device, ...

> diff --git a/Documentation/devicetree/bindings/hsi/omap_ssi.txt b/Documentation/devicetree/bindings/hsi/omap_ssi.txt

... and what is the "HSI" subsystem?

> +OMAP SSI controller bindings
> +
> +Required properties:
> +- compatible:		Should be set to the following value
> +                        ti,omap3-ssi (applicable to OMAP34xx devices)

I think that'd be better phrased as:

	Should include "ti,omap3-ssi".

The binding should not preclude other compatibel values being present
(e.g. a SoC-specific compatible value, to allow SoC-specific quirks to
be enabled later).

> +- ti,hwmods:		Name of the hwmod associated to the controller, which
> +			is "ssi".

I don't think we should add any more of that, for new bindings.

> +- reg:			Contains SSI register address range (base address and
> +			length).
> +- reg-names:		Contains the names of the address ranges. It's
> +                        expected, that "sys" and "gdd" address ranges are
> +			provided.

Why two entries in reg-names but only one in reg?

I think it'd be better to write:

reg-names:	Contains the values "sys" and "gdd".
reg:		Contains a register specifier for each entry in
		reg-names.

A similar re-ordering/-wording would apply to interrupts/interrupt-names.

> +- ranges		Required as an empty node

s/node/property/

Why must ranges be empty? As long as the content correctly represents
the bus setup, why does the content matter at all. How about:

ranges		Represents the bus address mapping between the main
		controller node and the child nodes below.

> +Each port is represented as a sub-node of the ti,omap3-ssi device.
> +
> +Required Port sub-node properties:
> +- compatible:		Should be set to the following value
> +                        ti,omap3-ssi-port (applicable to OMAP34xx devices)

Hmm. Is it really the case that there is 1 controller with n ports? Are
the ports really dependent upon some shared resource? Couldn't the ports
be represented as separate top-level SSI controllers?

> +- interrupts:		Contains the interrupt information for the port.
> +- interrupt-names:	Contains the names of the interrupts. It's expected,
> +			that "mpu_irq0" and "mpu_irq1" are provided.

What exactly are those interrupts? "MPU" sounds like an external
micro-controller/processor...

> +- ti,ssi-cawake-gpio:	Defines which GPIO pin is used to signify CAWAKE
> +			events for the port. This is an optional board-specific
> +			property. If it's missing the port will not be
> +			enabled.

That also sounds like something that's a higher-level protocol, rather
than whatever low-level transport "SSI" implements. Should this be part
of a child node that represents the device attached to the SSI controller?

Does the SSI controller (or its ports) not need any clocks, resets,
regulators, ...?

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux