To use a GPIO pin as an interrupt line, two previous configurations
have to be made:
a) Map the GPIO pin as an interrupt line into the Linux irq space
b) Enable the GPIO bank and configure the GPIO direction as input
Most GPIO/IRQ chip drivers just create a mapping for every single
GPIO pin with irq_create_mapping() on .probe so users usually can
assume a) and only have to do b) by using the following sequence:
gpio_request(gpio, "foo IRQ");
gpio_direction_input(gpio);
and then request a IRQ with:
irq = gpio_to_irq(gpio);
request_irq(irq, ...);
Some drivers know that their IRQ line is being driven by a GPIO
and use a similar sequence as the described above but others are
not aware or don't care wether their IRQ is a real line from an
interrupt controller or a GPIO pin acting as an IRQ.
In these cases board files did all the necessary GPIO setup so the
drivers could only call request_irq() on the provided IRQ.
Unfortuntaly this does not work when booting with Device Trees since
the OF irq core does neither request the GPIO nor set its direction.
A DTS just defines the GPIO controller phandle as a interrupt-parent
so drivers get the mapped GPIO-IRQ line but request_irq() fails since
the setup was never made.
The first attemp to solve this issue was by adding a custom .map()
irq_domain_ops function handler in the gpio-omap driver that called
gpio_request_one() to request and setup the GPIO direction as input.
This was made on commits:
0e970cec ("gpio/omap: don't create an IRQ mapping for every GPIO on DT")
b4419e1a ("gpio/omap: auto request GPIO as input if used as IRQ via DT")
but they got reverted since broke OMAP1 platforms.
This patch solves this issue with a different approach, by doing all
the needed hardware setup on the GPIO/IRQ chip driver when a call to
request_irq() is made.
Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
---
Hello,
This patch is an attempt to solve the long standing issue that we have been
discussing in thread:
"[PATCH v3] gpio: interrupt consistency check for OF GPIO IRQs" [1]
The fix is just for OMAP of course and not a kernel wide solution but Linus
approach (which I think is the best general solution proposed so far) has
some resistance so it seems that it won't be merged and we really need a
solution for OMAP if we want to finish our migration to Device Tree soon.
The patch is based on 3.12-rc1 but is not meant to be merged as a fix for
this -rc cycle. I would like it to be tested ideally on every OMAP platform
supported in mainline. So is better to wait until we are sure that this does
not cause a regression on any platform than ending reverting the patch like
it happened last time.
Thanks a lot and best regards,
Javier
[1]: https://lkml.org/lkml/2013/8/26/260
drivers/gpio/gpio-omap.c | 54 +++++++++++++++++++++++++++---------------------
1 file changed, 31 insertions(+), 23 deletions(-)
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 0ff4355..218ce3d 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -420,6 +420,29 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio,
return 0;
}
+static void _set_gpio_mode(struct gpio_bank *bank, unsigned offset)
+{
+ if (bank->regs->pinctrl) {
+ void __iomem *reg = bank->base + bank->regs->pinctrl;
+
+ /* Claim the pin for MPU */
+ __raw_writel(__raw_readl(reg) | (1 << offset), reg);
+ }
+
+ if (bank->regs->ctrl && !bank->mod_usage) {
+ void __iomem *reg = bank->base + bank->regs->ctrl;
+ u32 ctrl;
+
+ ctrl = __raw_readl(reg);
+ /* Module is enabled, clocks are not gated */
+ ctrl &= ~GPIO_MOD_CTRL_BIT;
+ __raw_writel(ctrl, reg);
+ bank->context.ctrl = ctrl;
+ }
+
+ bank->mod_usage |= 1 << offset;
+}
+
static int gpio_irq_type(struct irq_data *d, unsigned type)
{
struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
@@ -427,8 +450,8 @@ static int gpio_irq_type(struct irq_data *d, unsigned type)
int retval;
unsigned long flags;
- if (WARN_ON(!bank->mod_usage))
- return -EINVAL;
+ if (!bank->mod_usage)
+ pm_runtime_get_sync(bank->dev);
#ifdef CONFIG_ARCH_OMAP1
if (d->irq > IH_MPUIO_BASE)
@@ -438,6 +461,11 @@ static int gpio_irq_type(struct irq_data *d, unsigned type)
if (!gpio)
gpio = irq_to_gpio(bank, d->hwirq);
+ spin_lock_irqsave(&bank->lock, flags);
+ _set_gpio_mode(bank, GPIO_INDEX(bank, gpio));
+ _set_gpio_direction(bank, GPIO_INDEX(bank, gpio), 1);
+ spin_unlock_irqrestore(&bank->lock, flags);
+
if (type & ~IRQ_TYPE_SENSE_MASK)
return -EINVAL;
@@ -611,27 +639,7 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset)
* request_irq() or set_irq_type().
*/
_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
-
- if (bank->regs->pinctrl) {
- void __iomem *reg = bank->base + bank->regs->pinctrl;
-
- /* Claim the pin for MPU */
- __raw_writel(__raw_readl(reg) | (1 << offset), reg);
- }
-
- if (bank->regs->ctrl && !bank->mod_usage) {
- void __iomem *reg = bank->base + bank->regs->ctrl;
- u32 ctrl;
-
- ctrl = __raw_readl(reg);
- /* Module is enabled, clocks are not gated */
- ctrl &= ~GPIO_MOD_CTRL_BIT;
- __raw_writel(ctrl, reg);
- bank->context.ctrl = ctrl;
- }
-
- bank->mod_usage |= 1 << offset;
-
+ _set_gpio_mode(bank, offset);
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
--
1.8.4.rc3
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
