Re: [RFC PATCH 1/4] DRIVERS: IRQCHIP: Add crossbar irqchip driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Friday 13 September 2013 07:12 AM, Santosh Shilimkar wrote:
> On Thursday 12 September 2013 08:26 PM, Thomas Gleixner wrote:
>> On Thu, 12 Sep 2013, Santosh Shilimkar wrote:
>>> On Thursday 12 September 2013 06:22 PM, Thomas Gleixner wrote:
>>>> Now the real question is, how that expansion mechanism is supposed to
>>>> work. There are two possible scenarios:
>>>>
>>>> 1) Expand the number of handled interrupts beyond the GIC capacity:
>>>>
>>>>    That requires a mechanism in CROSSBAR to map several CROSSBAR
>>>>    interrupts to a particular GIC interrupt and provide a demux
>>>>    mechanism to invoke the shared handlers.
>>>>
>>> This is not possible in hardware and not supported. Hardware has
>>> no notion of muxing multiple IRQ's to generate 1 IRQ or ack etc
>>> functionality. Its a simple MUX to tie knots between input and output
>>> wires.
>> It's not a MUX. It's a ROUTING mechanism. That's similar to the
>> mechanisms which are used by MSI[X]. We assign arbitrary interrupt
>> numbers to a device and route them to some underlying limited hardware
>> interrupt controller.
>>
>>>> 2) Provide a mapping mechanism between possibly 250 interrupt numbers
>>>>    and a limitation of a total 160 active interrupts by the underlying
>>>>    GIC.
>>>>
>>> This is the need and problem we are trying to solve.
>> Let me summarize:
>>
>>    - GIC supports up to 160 interrupts
>>
>>    - CROSSBAR supports up to 250 interrupts 
>>
>>    - CROSSBAR routes up to 160 out of 250 interrupts to the GIC ones
>>
>>    - Drivers request a CROSSBAR interrupt number which must be mapped
>>      to some arbitrary available GIC irq number
>>
> Correct.
>
>> So basically the CROSSBAR mechanism is pretty much the same as MSI[X]
>> just in a different flavour and with a different set of semantics and
>> limitations, i.e. poor mans MSI[X] with a new level of bogosity.
>>
>> So if CROSSBAR is going to be the new fangled SoC MSI[X] long term
>> equivalent then you better provide some infrastructure for that and
>> make the drivers ready to use it. Maybe check with the PCI/MSI folks
>> to share some of the interfaces.
>>
>> If that whole thing is another onetime HW designers wet dream, then
>> please go back to the limited but completely functional (Who is going
>> to use more than 160 peripheral interrupts????) device tree model. I
>> really have no interest to support hardware designer brain farts.
>>
> Thanks for clear NAK for irqchip approach. I should have looped you
> in the discussion where I was also suggesting against the irqchip
> approach. We will try to look at MSI stuff but if its get too
> complicated am going to fall-back to the initial probe based
> approach to achieve the functionality.
>
> Thanks again for clear direction and useful discussion.
 Thanks for the feedback. I will look in to the MSI driver and
 see if how that would work.

Regards,
 Sricharan
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux