Provide RESET controller and Power regulator for the USB PHY,
the USB Host port mode and the PHY device. Provide
pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
arch/arm/boot/dts/omap3-beagle-xm.dts | 75 +++++++++++++++++++++++++++++----
1 files changed, 66 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index afdb164..2273c24 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -69,6 +69,33 @@
};
};
+
+ /* HS USB Port 2 RESET */
+ hsusb2_reset: hsusb2_reset {
+ compatible = "gpio-reset";
+ reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
+ reset-delay-us = <70000>;
+ initially-in-reset;
+ #reset-cells = <0>;
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ resets = <&hsusb2_reset>;
+ reset-names = "reset";
+ vcc-supply = <&hsusb2_power>;
+ };
};
&omap3_pmx_wkup {
@@ -79,6 +106,37 @@
};
};
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb2_pins
+ >;
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+ >;
+ };
+
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+};
+
&i2c1 {
clock-frequency = <2600000>;
@@ -148,15 +206,6 @@
power = <50>;
};
-&omap3_pmx_core {
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
- >;
- };
-};
-
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
@@ -166,3 +215,11 @@
pinctrl-names = "default";
pinctrl-0 = <&gpio1_pins>;
};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
