Picture format fixed. Sorry for that.
On 06/26/2013 04:20 PM, Grygorii Strashko wrote:
Hi All,
On 06/25/2013 09:58 AM, Tony Lindgren wrote:
* Linus Walleij <linus.walleij@xxxxxxxxxx> [130624 05:13]:
On Fri, Jun 21, 2013 at 5:03 PM, Grygorii Strashko
<grygorii.strashko@xxxxxx> wrote:
Hence, add pinctrl handling in omap_device core:
1) on PM runtime resume
- switch pinctrl state to "default" (todo: "active")
2) on PM runtime suspend
- switch pinctrl state to "idle"
3) during system wide suspend
- switch pinctrl state to "sleep" or "idle" if omap_device core
disables device
- switch pinctrl state to "sleep" if device is disabled already
Do you need a separate setting for "idle" and "sleep", or are
they the same?
4) during system wide resume
- switch pinctrl state to "default" (todo: "active") if omap_device
core has
disabled device during suspend
- switch pinctrl state to "idle" if device was already disabled
before suspend
I don't understand step 4.
I get the creeps about whether the system is runtime suspended
or runtime resumed when we come to resume proper, so I need
Kevin to have a look at this.
Apart from that it looks good.
Stephen and Tony are trying to figure out the details of whether
"active"
is necessary or not in a related thread I think.
Thanks for your comments.
I've prepared diagram to illustrate how does this work:
+
|
| .probe()
|
+-----v--------+
| |
| default |
| |
+----+--+------+
| |
pm_runtime_get()| | pm_runtime_put()
+----------------+ +------------+
| |
+------v------+ pm_runtime_put()+-------v-----+
| +-----------------> |
+-----------> Active |pm_runtime_get() | Idle <----------+
| | <-----------------+ | |
| +-------+-----+ +-------+-----+ |
| |.suspend_noirq() |.suspend_noirq()|
| | | |
| | | |
| | | |
| | | |
| +-------v-----+ +-------v-----+ |
| | | | | |
+-----------+ Sleep ------+ | Sleep +----------+
.resume_noirq() | | | | |.resume_noirq()
+-------|-----+ | +-------------+
| Idle |
+-----------+
The "Sleep" pinctrl state is optional - if "sleep" state isn't defined
then "Idle" pinctrl state will be used during suspend.
As per above pinctrl state transition diagram - I think, that:
- if "idle" or "sleep" states are defined then "active" state have to be
defined too.
So, pinctrl core should detect such situation and generate a warning.
From my point of view, we should have "active" state - it would allow
to avoid additional
runtime overhead and handle properly the case when drivers are used as
loadable modules.
In this case, after boot, device's pinctrl registers can have HW default
values (after reset) or
can be configured to some safe (off) state from board file (board's
"default" configuration).
Driver module will activate its PINs when loaded and need to restore
safe (off) PINs state when
unloaded.
As result, it seems, we should have "off" state which can be used when
driver's module is removed.
So, final list of default pnctrl states may be defined as "default",
"active", "idle", "sleep", "off":
- "active", "idle", "sleep": will be handled by omap_device core
- "default", "off": will be handled by driver itself (or Device core).
Yes we should have that sorted out over next few weeks, so let's
just wait a little while on all these dynamic remuxing patches
to avoid churn.
Regards,
Tony
Regards,
- grygorii
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
