Use a common naming scheme "mode0name.modename flags" for the USB host pins to be consistent. Also add a disclaimer stating that use of regulator framework for GPIO RESET line is temporary. Signed-off-by: Roger Quadros <rogerq@xxxxxx> --- arch/arm/boot/dts/omap3-beagle.dts | 29 +++++++++++++++++------------ 1 files changed, 17 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index dfd8310..587781a 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -44,6 +44,11 @@ }; }; + /* + * Temp hack: Need to be replaced with the proper gpio-controlled + * reset driver as soon it will be merged. + * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830 + */ /* HS USB Port 2 RESET */ hsusb2_reset: hsusb2_reset_reg { compatible = "regulator-fixed"; @@ -101,18 +106,18 @@ hsusbb2_pins: pinmux_hsusbb2_pins { pinctrl-single,pins = < - 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */ - 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */ - 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */ - 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */ - 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */ - 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */ - 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */ - 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */ - 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */ - 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */ - 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */ - 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */ + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ >; }; -- 1.7.4.1 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
