Rob, Grant,
On 03/15/2013 10:24 AM, Jon Hunter wrote:
>
> On 03/14/2013 04:54 PM, Javier Martinez Canillas wrote:
>> Besides being used to interface with external memory devices,
>> the General-Purpose Memory Controller can be used to connect
>> Pseudo-SRAM devices such as ethernet controllers to OMAP2+
>> processors using the TI GPMC as a data bus.
>>
>> This patch allows an ethernet chip to be defined as an GPMC
>> child device node.
>>
>> Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
>> ---
>>
>> Changes since v2:
>> - remove optional #address-cells and #size-cells since are not relevant for
>> ethernet chips; suggested by Jon Hunter.
>>
>> Changes since v1:
>> - Improve the DT binding documentation explaining that even when the GPMC
>> maximum bus address width is 16-bit, it supports devices with 32-bit
>> registers address width and the device property especifying this has to
>> be set accordingly; suggested by Jon Hunter.
>>
>> Documentation/devicetree/bindings/net/gpmc-eth.txt | 97 ++++++++++++++++++++
>> arch/arm/mach-omap2/gpmc.c | 8 ++
>> 2 files changed, 105 insertions(+), 0 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/net/gpmc-eth.txt
>>
>> diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt
>> new file mode 100644
>> index 0000000..24cb4e4
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt
>> @@ -0,0 +1,97 @@
>> +Device tree bindings for Ethernet chip connected to TI GPMC
>> +
>> +Besides being used to interface with external memory devices, the
>> +General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices
>> +such as ethernet controllers to processors using the TI GPMC as a data bus.
>> +
>> +Ethernet controllers connected to TI GPMC are represented as child nodes of
>> +the GPMC controller with an "ethernet" name.
>> +
>> +All timing relevant properties as well as generic GPMC child properties are
>> +explained in a separate documents. Please refer to
>> +Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> +
>> +For the properties relevant to the ethernet controller connected to the GPMC
>> +refer to the binding documentation of the device. For example, the documentation
>> +for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt
>> +
>> +Child nodes need to specify the GPMC bus address width using the "bank-width"
>> +property but is possible that an ethernet controller also has a property to
>> +specify the I/O registers address width. Even when the GPMC has a maximum 16-bit
>> +address width, it supports devices with 32-bit word registers.
>> +For example with an SMSC LAN911x/912x controller connected to the TI GPMC on an
>> +OMAP2+ board, "bank-width = <2>;" and "reg-io-width = <4>;".
>> +
>> +Required properties:
>> +- bank-width: Address width of the device in bytes. GPMC supports 8-bit
>> + and 16-bit devices and so must be either 1 or 2 bytes.
>> +- compatible: Compatible string property for the ethernet child device.
>> +- gpmc,cs-on: Chip-select assertion time
>> +- gpmc,cs-rd-off: Chip-select de-assertion time for reads
>> +- gpmc,cs-wr-off: Chip-select de-assertion time for writes
>> +- gpmc,oe-on: Output-enable assertion time
>> +- gpmc,oe-off Output-enable de-assertion time
>> +- gpmc,we-on: Write-enable assertion time
>> +- gpmc,we-off: Write-enable de-assertion time
>> +- gpmc,access: Start cycle to first data capture (read access)
>> +- gpmc,rd-cycle: Total read cycle time
>> +- gpmc,wr-cycle: Total write cycle time
>> +- reg: Chip-select, base address (relative to chip-select)
>> + and size of the memory mapped for the device.
>> + Note that base address will be typically 0 as this
>> + is the start of the chip-select.
>> +
>> +Optional properties:
>> +- gpmc,XXX Additional GPMC timings and settings parameters. See
>> + Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> +
>> +Example:
>> +
>> +gpmc: gpmc@6e000000 {
>> + compatible = "ti,omap3430-gpmc";
>> + ti,hwmods = "gpmc";
>> + reg = <0x6e000000 0x1000>;
>> + interrupts = <20>;
>> + gpmc,num-cs = <8>;
>> + gpmc,num-waitpins = <4>;
>> + #address-cells = <2>;
>> + #size-cells = <1>;
>> +
>> + ranges = <5 0 0x2c000000 0x1000000>;
>> +
>> + ethernet@5,0 {
>> + compatible = "smsc,lan9221", "smsc,lan9115";
>> + reg = <5 0 0xff>;
>> + bank-width = <2>;
>> +
>> + gpmc,mux-add-data;
>> + gpmc,cs-on = <0>;
>> + gpmc,cs-rd-off = <186>;
>> + gpmc,cs-wr-off = <186>;
>> + gpmc,adv-on = <12>;
>> + gpmc,adv-rd-off = <48>;
>> + gpmc,adv-wr-off = <48>;
>> + gpmc,oe-on = <54>;
>> + gpmc,oe-off = <168>;
>> + gpmc,we-on = <54>;
>> + gpmc,we-off = <168>;
>> + gpmc,rd-cycle = <186>;
>> + gpmc,wr-cycle = <186>;
>> + gpmc,access = <114>;
>> + gpmc,page-burst-access = <6>;
>> + gpmc,bus-turnaround = <12>;
>> + gpmc,cycle2cycle-delay = <18>;
>> + gpmc,wr-data-mux-bus = <90>;
>> + gpmc,wr-access = <186>;
>> + gpmc,cycle2cycle-samecsen;
>> + gpmc,cycle2cycle-diffcsen;
>> +
>> + interrupt-parent = <&gpio6>;
>> + interrupts = <16>;
>> + vmmc-supply = <&vddvario>;
>> + vmmc_aux-supply = <&vdd33a>;
>> + reg-io-width = <4>;
>> +
>> + smsc,save-mac-address;
>> + };
>> +};
>> diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
>> index 898b44d..2bc276b 100644
>> --- a/arch/arm/mach-omap2/gpmc.c
>> +++ b/arch/arm/mach-omap2/gpmc.c
>> @@ -1559,6 +1559,14 @@ static int gpmc_probe_dt(struct platform_device *pdev)
>> }
>> }
>>
>> + for_each_node_by_name(child, "ethernet") {
>> + ret = gpmc_probe_generic_child(pdev, child);
>> + if (ret < 0) {
>> + of_node_put(child);
>> + return ret;
>> + }
>> + }
>> +
>> return 0;
>> }
>> #else
>
> Thanks! I have added this to my gpmc branch [1].
If you are ok with the Documentation part, can you ACK this?
Thanks
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
