Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for USB host
pins.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
arch/arm/boot/dts/omap3-beagle.dts | 71 ++++++++++++++++++++++++++++++++++++
1 files changed, 71 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index f624dc8..02d23f1 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -38,6 +38,57 @@
};
};
+ /* HS USB Port 2 RESET */
+ hsusb2_reset: hsusb2_reset_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_reset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 19 0>; /* gpio_147 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-supply = <&hsusb2_reset>;
+ vcc-supply = <&hsusb2_power>;
+ };
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb2_pins
+ >;
+
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk OUTPUT */
+ 0x5c2 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */
+ 0x5c4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */
+ 0x5c6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */
+ 0x5c8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */
+ 0x5cA 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */
+ 0x1a4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */
+ 0x1a6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */
+ 0x1a8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */
+ 0x1aa 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */
+ 0x1ac 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */
+ 0x1ae 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */
+ >;
+ };
};
&i2c1 {
@@ -65,3 +116,23 @@
&mmc3 {
status = "disabled";
};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+&twl_gpio {
+ ti,use-leds;
+ /* pullups: BIT(1) */
+ ti,pullups = <0x000002>;
+ /*
+ * pulldowns:
+ * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+ * BIT(15), BIT(16), BIT(17)
+ */
+ ti,pulldowns = <0x03a1c4>;
+};
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
