On Wed, Nov 14, 2012 at 10:31:42, AnilKumar, Chimata wrote:
> +Mark
>
> On Mon, Nov 12, 2012 at 15:17:13, AnilKumar, Chimata wrote:
> > On Tue, Nov 06, 2012 at 22:26:54, Cousson, Benoit wrote:
> > > Hi Anil,
> > >
> > > On 11/06/2012 06:07 AM, AnilKumar, Chimata wrote:
> > > > On Mon, Nov 05, 2012 at 22:13:25, Cousson, Benoit wrote:
> > > >> Hi Anil / Colin,
> > > >>
> > > >> On 11/05/2012 10:42 AM, AnilKumar Ch wrote:
> > > >>> From: Colin Foe-Parker <colin.foeparker@xxxxxxxxxxx>
> > > >>>
> > > >>> Add system power off control to rtc driver which is the in-charge
> > > >>> of controlling the BeagleBone system power. The power_off routine
> > > >>> can be hooked up to "pm_power_off" system call.
> > > >>>
> > > >>> System power off sequence:-
> > > >>> * Set PMIC STATUS_OFF when PMIC_POWER_EN is pulled low
> > > >>> * Enable PMIC_POWER_EN in rtc module
> > > >>> * Set rtc ALARM2 time
> > > >>> * Enable ALARM2 interrupt
> > > >>>
> > > >>> Added while (1); after the above steps to make sure that no other
> > > >>> process acquire cpu. Otherwise we might see an unexpected behaviour
> > > >>> because we are shutting down all the power rails of SoC except RTC.
> > > >>>
> > > >>> Signed-off-by: Colin Foe-Parker <colin.foeparker@xxxxxxxxxxx>
> > > >>> [anilkumar@xxxxxx: move poweroff additions to rtc driver]
> > > >>> Signed-off-by: AnilKumar Ch <anilkumar@xxxxxx>
> > > >>> ---
> > > >>> Documentation/devicetree/bindings/rtc/rtc-omap.txt | 5 ++
> > > >>> drivers/rtc/rtc-omap.c | 79 +++++++++++++++++++-
> > > >>> 2 files changed, 83 insertions(+), 1 deletion(-)
> > > >>>
> > > >>> diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> > > >>> index b47aa41..8d9f4f9 100644
> > > >>> --- a/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> > > >>> +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> > > >>> @@ -6,6 +6,10 @@ Required properties:
> > > >>> - interrupts: rtc timer, alarm interrupts in order
> > > >>> - interrupt-parent: phandle for the interrupt controller
> > > >>>
> > > >>> +Optional properties:
> > > >>> +- ti,system-power-controller: Telling whether or not rtc is controlling
> > > >>> + the system power.
> > > >>
> > > >> I don't know how it is connected at board level, but I'm not sure the
> > > >> binding is the proper one.
> > > >
> > > > Hi Benoit,
> > > > ________________________________
> > > > | ______ _______ |
> > > > | | | | | |
> > > > | |RTC | | | |
> > > > | |PMIC | Line | | |
> > > > | |PWR_EN|=======>|PWR_EN | |
> > > > | |______| |_______| |
> > > > | AM335x SoC TPS65217 |
> > > > | |
> > > > |________________________________|
> > > > BeagleBone
> > > >
> > > > This is how RTC PMIC_PWR_EN is connected to PWR_EN of TPS65217 PMIC. Only when
> > > > RTC pull low in PMIC_PWR_EN then PMIC will go to power off state provided TPS65217
> > > > status should be changed to STATUS_OFF.
> > > >
> > > > ALARM2 event should be trigger to configure PMIC_PWR_EN properly then the "Line"
> > > > driven low so that PMIC will go to shutdown mode.
Mark,
Details regarding how PMIC PWR_EN is connected to RTC module
Thanks
AnilKumar
> > >
> > > Thanks for the nice diagram :-)
> >
> > I missed this mail thread so delayed in response
> >
> > >
> > > I'm wondering if we cannot abuse the gpio binding to describe that
> > > connection instead of creating two custom attributes (PMIC + RTC).
> > >
> > > Ideally we should do that without having to change the RTC to use the
> > > gpiolib at all.
> > >
> > >
> > > rtc: rtc@44e3e000 {
> > > compatible = "ti,da830-rtc";
> > > reg = <0x44e3e000 0x1000>;
> > > interrupts = <75, 76>;
> > > ti,hwmods = "rtc";
> > >
> > > /* expose the PWR_EN functionality of this RTC*/
> > > gpio-controller;
> > > #gpio-cells = <0>; /* assuming we can use 0 ??? */
> > > };
> > >
> > > ...
> > >
> > > tps: tps@24 {
> > > compatible = "ti,tps65217";
> > > /*
> > > * Enable the power enable feature from
> > > * the input line if that attribute is there.
> > > */
> > > gpio-power-en = <&rtc>; /* PWR_EN */
> > >
> > > ...
> > > }
> > >
> > > Any thought?
> >
> > No, these two are independent controllers. PMIC can go to power
> > off mode if we pull PWR_EN to low. We can pull down that line
> > by any means like PRCM or GPIO or some other. So these two flags
> > should be independent from each other.
> >
> > Thanks
> > AnilKumar
> >
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
