This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@xxxxxx>
Cc: Grant Likely <grant.likely@xxxxxxxxxxxx>
Cc: Rob Herring <rob.herring@xxxxxxxxxxx>
Cc: Rob Landley <rob@xxxxxxxxxxx>
---
Changes since v1:
- Add separate patch for pinctrl support
- Add conditional check for PWM subsystem clock enable.
- Combined with HWMOD changes & DT bindings.
- Remove the custom of xlate support.
:000000 100644 0000000... fe24cac... A Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
:100644 100644 d6d4cf0... 0d43266... M drivers/pwm/pwm-tiecap.c
.../devicetree/bindings/pwm/pwm-tiecap.txt | 22 +++++++++
drivers/pwm/pwm-tiecap.c | 48 +++++++++++++++++++-
2 files changed, 69 insertions(+), 1 deletions(-)
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
new file mode 100644
index 0000000..fe24cac
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -0,0 +1,22 @@
+TI SOC ECAP based APWM controller
+
+Required properties:
+- compatible: Must be "ti,am33xx-ecap"
+- #pwm-cells: Should be 3. Number of cells being used to specify PWM property.
+ First cell specifies the per-chip index of the PWM to use, the second
+ cell is the period cycle in nanoseconds and bit 0 in the third cell is
+ used to encode the polarity of PWM output.
+- reg: physical base address and size of the registers map.
+
+Optional properties:
+- ti,hwmods: Name of the hwmod associated to the ECAP:
+ "ecap<x>", <x> being the 0-based instance number from the HW spec
+
+Example:
+
+ecap0: ecap@0 {
+ compatible = "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x48300100 0x80>;
+ ti,hwmods = "ecap0";
+};
diff --git a/drivers/pwm/pwm-tiecap.c b/drivers/pwm/pwm-tiecap.c
index d6d4cf0..0d43266 100644
--- a/drivers/pwm/pwm-tiecap.c
+++ b/drivers/pwm/pwm-tiecap.c
@@ -25,6 +25,9 @@
#include <linux/clk.h>
#include <linux/pm_runtime.h>
#include <linux/pwm.h>
+#include <linux/of_device.h>
+
+#include "tipwmss.h"
/* ECAP registers and bits definitions */
#define CAP1 0x08
@@ -37,6 +40,13 @@
#define ECCTL2_SYNC_SEL_DISA (BIT(7) | BIT(6))
#define ECCTL2_TSCTR_FREERUN BIT(4)
+#define ECAPCLK_EN BIT(0)
+#define ECAPCLK_STOP_REQ BIT(1)
+
+#define ECAPCLK_EN_ACK BIT(0)
+
+#define PWM_CELL_SIZE 3
+
struct ecap_pwm_chip {
struct pwm_chip chip;
unsigned int clk_rate;
@@ -184,6 +194,16 @@ static const struct pwm_ops ecap_pwm_ops = {
.owner = THIS_MODULE,
};
+#ifdef CONFIG_OF
+static const struct of_device_id ecap_of_match[] = {
+ {
+ .compatible = "ti,am33xx-ecap",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ecap_of_match);
+#endif
+
static int __devinit ecap_pwm_probe(struct platform_device *pdev)
{
int ret;
@@ -211,6 +231,7 @@ static int __devinit ecap_pwm_probe(struct platform_device *pdev)
pc->chip.dev = &pdev->dev;
pc->chip.ops = &ecap_pwm_ops;
+ pc->chip.of_pwm_n_cells = PWM_CELL_SIZE;
pc->chip.base = -1;
pc->chip.npwm = 1;
@@ -231,14 +252,37 @@ static int __devinit ecap_pwm_probe(struct platform_device *pdev)
}
pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
+ if (!(pwmss_submodule_state_change(pdev->dev.parent, ECAPCLK_EN) &
+ ECAPCLK_EN_ACK)) {
+ dev_err(&pdev->dev, "PWMSS config space clock enable failure\n");
+ ret = -EINVAL;
+ goto pwmss_clk_failure;
+ }
+ pm_runtime_put_sync(&pdev->dev);
+
platform_set_drvdata(pdev, pc);
return 0;
+
+pwmss_clk_failure:
+ pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+ pwmchip_remove(&pc->chip);
+ return ret;
}
static int __devexit ecap_pwm_remove(struct platform_device *pdev)
{
struct ecap_pwm_chip *pc = platform_get_drvdata(pdev);
+ pm_runtime_get_sync(&pdev->dev);
+ /*
+ * Due to hardware misbehaviour, acknowledge of the stop_req
+ * is missing. Hence checking of the status bit skipped.
+ */
+ pwmss_submodule_state_change(pdev->dev.parent, ECAPCLK_STOP_REQ);
+ pm_runtime_put_sync(&pdev->dev);
+
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
return pwmchip_remove(&pc->chip);
@@ -246,7 +290,9 @@ static int __devexit ecap_pwm_remove(struct platform_device *pdev)
static struct platform_driver ecap_pwm_driver = {
.driver = {
- .name = "ecap",
+ .name = "ecap",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(ecap_of_match),
},
.probe = ecap_pwm_probe,
.remove = __devexit_p(ecap_pwm_remove),
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
