Hi, On Wed, Oct 24, 2012 at 10:58:53AM -0700, Dmitry Torokhov wrote: > On Wednesday, October 24, 2012 07:57:49 PM Felipe Balbi wrote: > > Hi, > > > > On Wed, Oct 24, 2012 at 09:18:01AM -0700, Dmitry Torokhov wrote: > > > On Wed, Oct 24, 2012 at 02:54:23PM +0200, Linus Walleij wrote: > > > > On Tue, Oct 23, 2012 at 10:02 PM, Dmitry Torokhov > > > > > > > > <dmitry.torokhov@xxxxxxxxx> wrote: > > > > > I have seen just in a few days 3 or 4 drivers having exactly the same > > > > > change - call to devm_pinctrl_get_select_default(), and I guess I will > > > > > receive the same patches for the rest of input drivers shortly. > > > > > This suggests that the operation is done at the wrong level. Do the > > > > > pin configuration as you parse DT data, the same way you set up i2c > > > > > devices registers in of_i2c.c, and leave the individual drivers that > > > > > do > > > > > not care about specifics alone. > > > > > > > > Exactly this can be done with pinctrl hogs. > > > > > > > > The problem with that is that it removes the cross-reference > > > > between the device and it's pinctrl handle (also from the device > > > > tree). Instead the pinctrl handle gets referenced to the pin controller > > > > itself. So from a modelling perpective this looks a bit ugly. > > > > > > > > So we have two kinds of ugly: > > > > > > > > - Sprinke devm_pinctrl_get_select_default() over all drivers > > > > > > > > which makes pinctrl handles properly reference their devices > > > > > > > > - Use hogs and loose coupling between pinctrl handles and their > > > > > > > > devices > > > > > > > > A third alternative as outlined is to use notifiers and some > > > > resource core in drivers/base/* > > > > > > OK, so with drivers/base/, have you considered doing default pinctrl > > > selection in bus's probe() methods? Yo would select the default > > > configuration before starting probing the device and maybe select idle > > > when probe fails or device is unbound? That would still keep the link > > > between device object and pinctrl and there less busses than device > > > drivers out there. > > > > it starts to become confusing after a while. I mean, there's a reason > > why all drivers explictly call pm_runtim_enable(), right ? > > Right. Because not all of them support runtime PM and quite usually their > PM methods are not ready to go until initialization is complete. And again, > the driver here controls its own behavior. likewise not all devices will need pin muxing, those which do (granted, an increasing number of them since transistor size continue to shrink, allowing chip manufacturers to pack more features inside a single die, while the number of external pins/balls remain the same), will call pinctrl to setup muxing right. > > From a first thought, one could think of just yanking that into bus' > > probe() as you may suggest, but sometimes the device is already enabled, > > so we need extra tricks: > > > > pm_runtime_set_active(); > > pm_runtime_enable(); > > pm_runtime_get(); > > > > the same could happen with pinctrl eventually. What if a device needs to > > do something else (an errata fix as an example) before requesting > > pinctrl's default state ? > > That is a valid concern and we'll need to find a compromise here. As I said, WHAT ?? Silicon erratas are not a valid concern ? Power waste isn't a valid concern ? Tell that to the millions of devices shipped with Linux everyday. Power usage if it's the top concern in any product, is right there as the top five. Likewise for silicon erratas. Let's face it, just like SW, HW has bugs; the difference is that no company will continue to do several spins of an ASIC just because some SW engineer doesn't get concerned about a silicon bug. It's just too expensive to re-spin the ASIC. And even if we get another revision of the ASIC, we still need to support the older version as there might be cellphones, laser welding machines, IPTVs and whatever product already shipped. > I am not saying that no driver should ever touch pinctrl. I can see, for > example, input drivers actually disabling pins until they are ->open()ed, > in addition of doing that at [runtime] suspend/resume. But it would be nice > if we could have "dumb" drivers not care about pins. Like I replied on another sub-thread, this will just create exceptions to the rule which is far more messy than having a couple of extra lines of code in a few drivers. We can even argue that eventually all drivers will need to toggle pins in runtime in order to save that extra microwatt of runtime power consumption, so why bother adding exceptions ? In fact, we already have the exception: drivers which don't need to fiddle with pin muxing, just don't use pinctrl. The ones you're receiving today are the one which, for whatever reason, need to make sure pin muxing is right. If it's not toggling in runtime, it might just be because $AUTHOR decided that it would be best to do thing in small steps (don't we all agree with that ?). Maybe he thought that changing pins in runtime could cause problems, so let's get bare minimum in mainline and work towards optimizations in parallel. All in all, I don't see why you're complaining so much about a couple of lines of code. Even if it needs to be added to all drivers in tree. So what ? As long as pinctrl works fine in multiple platforms, what is done for e.g. OMAP2 should work fine in OMAP3/4/5. An even more complex example: what works on OMAP, should work on Exynos, Tegra, etc, if the same driver is used accross those platforms. -- balbi
Attachment:
signature.asc
Description: Digital signature
