On 10/18/2012 11:16 AM, Hiremath, Vaibhav wrote: > On Wed, Oct 17, 2012 at 01:17:56, Hunter, Jon wrote: >> >> On 10/15/2012 02:16 PM, Richard Cochran wrote: >>> From: hvaibhav@xxxxxx <hvaibhav@xxxxxx> >>> >>> With recent changes in omap gpmc driver code, in case of DT >>> boot mode, where bootloader does not configure gpmc cs space >>> will result into kernel BUG() inside gpmc_mem_init() function, >>> as gpmc cs0 gpmc_config7[0].csvalid bit is set to '1' and >>> gpmc_config7[0].baseaddress is set to '0' on reset. >> >> I am not sure I completely follow the logic here. >> >> Won't this problem occur if the bootloader does not configure the gpmc >> cs space AND we are not using DT? >> > > That's what exactly the above comment describes. Hmm ... you said "in the case of DT", but I am saying even "in the case WITHOUT DT" this can happen. So I think the subject is mis-leading. >> Is the csvalid bit set because we are booting from the internal ROM? >> > > As per TRM, the reset value of the CS0_valis bit is set to 0. I have pasted > TRM statement below - > > "Chip-select enable (reset value is 1 for CS[0] and 0 for CS[1-5])." The above two sentences don't see to agree ... > And same applies to OMAP3 family of devices. For which boot-modes? All or just the gpmc boot-modes? My omap3430 beagle has been booting with DT fine for some time and I have not encountered this problem even on the latest kernel with the gpmc driver present. >> I guess I don't see why csvalid bit being set and a base-address of 0x0 >> should not be allowed. That should be a valid combination. >> > > Yes, agreed. > >> One problem I see with gpmc_mem_init() is that it assumes that >> BOOT_ROM_SPACE is 1MB for all devices starting at 0x0 apart from the >> apollon board. For newer devices such as OMAP4, there is only 48KB of >> internal ROM and only mapped to 0x0 when booting from internal ROM. So >> this needs to be fixed. >> >> How much internal ROM does the AM335x have and where is it mapped? >> > > AM33xx memory map is something like, > > Boot ROM 0x4000_0000 0x4001_FFFF 128KB > 0x4002_0000 0x4002_BFFF 48KB 32-bit Ex/R(1) - Public > Reserved 0x4002_C000 0x400F_FFFF 848KB Reserved > Reserved 0x4010_0000 0x401F_FFFF 1MB Reserved > Reserved 0x4020_0000 0x402E_FFFF 960KB Reserved > Reserved 0x402f_0000 0x4020_03FF 64KB Reserved > SRAM internal 0x402F_0400 0x402F_FFFF 32-bit Ex/R/W(1) Does the boot ROM get mapped to 0x0, when booting from ROM? >>> This use-case is applicable for any board/EVM which doesn't have >>> any peripheral connected to gpmc cs0, for example BeagleXM and >>> BeagleBone, so DT boot mode fails. >>> >>> This patch adds of_have_populated_dt() check before creating >>> device, so that for DT boot mode, gpmc probe will not be called >>> which is expected behavior, as gpmc is not supported yet from DT. >> >> Yes, but we do actually still allow some platform devices to be probed >> (such as dmtimers) when booting with DT that don't support DT yet. So >> this change prevents us from using the gpmc on boards when booting with DT. >> > > The idea here was, > > In order to use GPMC in meaningful way, where some peripheral is connected > to the GPMC, you must create platform_device for the probe to happen > properly. Now all the devices I know so far, we have gpmc_smsc911x_init(), > omap_nand_flash_init(), etc... > These api's are getting called only through machine_desc.init_xxx callbacks, > And in case of DT, we have centralized machine_desc definition for all > platforms (board-generic.c). So even though you want to use GPMC for DT boot > mode, you can not make use of peripheral without changing board-files to > change to create platform_device. > > Does it make sense? Sure, if you are using one of the generic machine configurations for DT. However, while this migration happens people may create their own custom machine configurations for DT for testing things like smsc911x. >> I am not convinced that this is addressing the underlying problem with >> gpmc_mem_init(). >> > > The patch you submitted is cleanup patch and is required irrespective of > this patch. I believe this patch is just makes sure that, if you are booting > from DT and you do not have meaningful DT node for GPMC and peripheral > interfaced to it, no point in probing it. > > Does it make any sense??? Yes, but do you also see the bug that is hiding in gpmc_mem_init()? My point is to highlight this and not hide it, so that we can fix it now. Otherwise if we wait until we enable the gpmc driver with DT and this could hinder the DT migration later. Jon -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
