Hi Thomas,
Thomas Petazzoni <thomas.petazzoni@xxxxxxxxxxxxxxxxxx> writes:
> Kevin,
>
> Reviving an old thread.
>
> On Fri, 04 May 2012 16:46:32 -0700, Kevin Hilman wrote:
>
>> >> Thomas Petazzoni <thomas.petazzoni@xxxxxxxxxxxxxxxxxx> writes:
>> >>
>> >> > I have an IGEPv2 revision 6 board, which uses the DM3730 OMAP3.
>> >> > With 3.2 omap2plus_defconfig, the system boots fine and have a
>> >> > working shell on ttyO2. On either 3.3, 3.4-rc5 or
>> >> > arm-soc/for-next from Arnd, the system boots all the way up to
>> >> > showing the shell prompt, but I can't type any character, as if
>> >> > UART RX was broken.
>> >>
>> >> On v3.4-rc, can you see if reverting
>> >> bce492c04ba8fc66a4ea0a52b181ba255daaaf54 has any effect?
>> >>
>> >> That patch had some unfortunate side effects, but I haven't seen
>> >> the problem you see, so I'm not sure if it's related.
>> >
>> > Reverting bce492c04ba8fc66a4ea0a52b181ba255daaaf54 is a broken
>> > solution like you mentioned. But if it helps, then the proper fix
>> > is to add muxing to board-*.c files for the uart pins and use
>> > omap_serial_init_port for each uart instead of omap_serial_init.
>> > That should fix the wake-up issues too.
>>
>> I agree on the final solution, but just wanted to see if the missing
>> mux (and thus disabled runtime PM) is what's causing the problem.
>
> FWIW, I tried the recently released 3.6 kernel on this platform
> (IGEPv2, OMAP3-based), and I still see the same problem. Upon Tony's
> suggestion, I tried to add some code in board-igep0020.c similar to the
> one in board-n8x0.c to do the appropriate UART2 muxing, but it doesn't
> seem to improve the situation. I did the following change (note that I
> tried with both .name = "uart2_rx_irrx.uart2_rx_irrx" and .name =
> "uart3_rx_irrx.uart3_rx_irrx"). On this board, the console is on ttyO2.
> This is with the plain omap2plus_defconfig, so CONFIG_OMAP_MUX is
> enabled.
>
> Any idea of things to try? This board has been broken since 3.2, so I'd
> like to get it fixed at some point :-)
Can you dump the UART mux registers on a working kernel and compare them
to the broken one? (Table 7-4 in the 34xx public TRM[1] will list all
the mux registers.) Maybe the bootloader code for that board will shed
some light as well since it will be setting the muxing too.
If the console uart is ttyO2 (UART3 in TI docs), then the interesting
registers will be any of the padconf registers in that table that
contain 'uart3'. e.g. for UART3 RX:
CONTROL_PADCONF_DSS_DATA4 (mode 2)
CONTROL_PADCONF_UART3_RTS_SD (mode 0)
CONTROL_PADCONF_HSUSB0_DATA1 (mode 2)
omap_mux has some useful debugfs output under <debugfs>/omap_mux. For
example:
# cd /sys/kernel/debug/omap_mux
# cat dss_data4
# cat uart3_rx_irrx
# cat hsusb0_data1
would provide a very useful comparison between a working kernel and a
non-working one.
Kevin
[1] http://www.ti.com/pdfs/wtbu/OMAP34xx_ES3.1.x_PUBLIC_TRM_vZV.zip
> diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
> index 2821448..568f13e 100644
> --- a/arch/arm/mach-omap2/board-igep0020.c
> +++ b/arch/arm/mach-omap2/board-igep0020.c
> @@ -558,6 +558,43 @@ static struct omap_board_mux board_mux[] __initdata = {
> OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
> { .reg_offset = OMAP_MUX_TERMINATOR },
> };
> +
> +static struct omap_device_pad serial2_pads[] __initdata = {
> + {
> + .name = "uart2_rx_irrx.uart2_rx_irrx",
> + .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
> + .enable = OMAP_MUX_MODE0,
> + .idle = OMAP_MUX_MODE3 /* Mux as GPIO for idle */
> + },
> +};
> +
> +static inline void board_serial_init(void)
> +{
> + struct omap_board_data bdata;
> +
> + bdata.flags = 0;
> + bdata.pads = NULL;
> + bdata.pads_cnt = 0;
> +
> + bdata.id = 0;
> + omap_serial_init_port(&bdata, NULL);
> +
> + bdata.id = 1;
> + omap_serial_init_port(&bdata, NULL);
> +
> + bdata.id = 2;
> + bdata.pads = serial2_pads;
> + bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
> + omap_serial_init_port(&bdata, NULL);
> +}
> +
> +#else
> +
> +static inline void board_serial_init(void)
> +{
> + omap_serial_init();
> +}
> +
> #endif
>
> #if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
> @@ -621,7 +658,7 @@ static void __init igep_init(void)
> /* Register I2C busses and drivers */
> igep_i2c_init();
> platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
> - omap_serial_init();
> + board_serial_init();
> omap_sdrc_init(m65kxxxxam_sdrc_params,
> m65kxxxxam_sdrc_params);
> usb_musb_init(NULL);
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
