smsc ece1099 is a keyboard scan or gpio expansion device. The patch create keypad and gpio expander child for this multi function smsc driver. Cc: Samuel Ortiz <sameo@xxxxxxxxxxxxxxx> Cc: Benoit Cousson <b-cousson@xxxxxx> Cc: Felipe Balbi <balbi@xxxxxx> Cc: Santosh Shilimkar <santosh.shilimkar@xxxxxx> Signed-off-by: Sourav Poddar <sourav.poddar@xxxxxx> --- Documentation/smsc_ece1099.txt | 56 ++++++++++++++++ drivers/mfd/Kconfig | 10 +++ drivers/mfd/Makefile | 1 + drivers/mfd/smsc-ece1099.c | 139 ++++++++++++++++++++++++++++++++++++++++ include/linux/mfd/smsc.h | 89 +++++++++++++++++++++++++ 5 files changed, 295 insertions(+), 0 deletions(-) create mode 100644 Documentation/smsc_ece1099.txt create mode 100644 drivers/mfd/smsc-ece1099.c create mode 100644 include/linux/mfd/smsc.h diff --git a/Documentation/smsc_ece1099.txt b/Documentation/smsc_ece1099.txt new file mode 100644 index 0000000..6b492e8 --- /dev/null +++ b/Documentation/smsc_ece1099.txt @@ -0,0 +1,56 @@ +What is smsc-ece1099? +---------------------- + +The ECE1099 is a 40-Pin 3.3V Keyboard Scan Expansion +or GPIO Expansion device. The device supports a keyboard +scan matrix of 23x8. The device is connected to a Master +via the SMSC BC-Link interface or via the SMBus. +Keypad scan Input(KSI) and Keypad Scan Output(KSO) signals +are multiplexed with GPIOs. + +Interrupt generation +-------------------- + +Interrupts can be generated by an edge detection on a GPIO +pin or an edge detection on one of the bus interface pins. +Interrupts can also be detected on the keyboard scan interface. +The bus interrupt pin (BC_INT# or SMBUS_INT#) is asserted if +any bit in one of the Interrupt Status registers is 1 and +the corresponding Interrupt Mask bit is also 1. + +In order for software to determine which device is the source +of an interrupt, it should first read the Group Interrupt Status Register +to determine which Status register group is a source for the interrupt. +Software should read both the Status register and the associated Mask register, +then AND the two values together. Bits that are 1 in the result of the AND +are active interrupts. Software clears an interrupt by writing a 1 to the +corresponding bit in the Status register. + +Communication Protocol +---------------------- + +- SMbus slave Interface + The host processor communicates with the ECE1099 device + through a series of read/write registers via the SMBus + interface. SMBus is a serial communication protocol between + a computer host and its peripheral devices. The SMBus data + rate is 10KHz minimum to 400 KHz maximum + +- Slave Bus Interface + The ECE1099 device SMBus implementation is a subset of the + SMBus interface to the host. The device is a slave-only SMBus device. + The implementation in the device is a subset of SMBus since it + only supports four protocols. + + The Write Byte, Read Byte, Send Byte, and Receive Byte protocols are the + only valid SMBus protocols for the device. + +- BC-LinkTM Interface + The BC-Link is a proprietary bus that allows communication + between a Master device and a Companion device. The Master + device uses this serial bus to read and write registers + located on the Companion device. The bus comprises three signals, + BC_CLK, BC_DAT and BC_INT#. The Master device always provides the + clock, BC_CLK, and the Companion device is the source for an + independent asynchronous interrupt signal, BC_INT#. The ECE1099 + supports BC-Link speeds up to 24MHz. diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index d1facef..3b81c17 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -385,6 +385,16 @@ config MFD_T7L66XB help Support for Toshiba Mobile IO Controller T7L66XB +config MFD_SMSC + bool "Support for the SMSC ECE1099 series chips" + depends on I2C=y && MFD_CORE && REGMAP_I2C + help + If you say yes here you get support for the + ece1099 chips from SMSC. + + To compile this driver as a module, choose M here: the + module will be called smsc. + config MFD_TC6387XB bool "Support Toshiba TC6387XB" depends on ARM && HAVE_CLK diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 79dd22d..f587d91 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -77,6 +77,7 @@ obj-$(CONFIG_EZX_PCAP) += ezx-pcap.o obj-$(CONFIG_MCP) += mcp-core.o obj-$(CONFIG_MCP_SA11X0) += mcp-sa11x0.o obj-$(CONFIG_MCP_UCB1200) += ucb1x00-core.o +obj-$(CONFIG_MFD_SMSC) += smsc.o obj-$(CONFIG_MCP_UCB1200_TS) += ucb1x00-ts.o ifeq ($(CONFIG_SA1100_ASSABET),y) diff --git a/drivers/mfd/smsc-ece1099.c b/drivers/mfd/smsc-ece1099.c new file mode 100644 index 0000000..6ba06b8 --- /dev/null +++ b/drivers/mfd/smsc-ece1099.c @@ -0,0 +1,139 @@ +/* + * TI SMSC MFD Driver + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * + * Author: Sourav Poddar <sourav.poddar@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; GPL v2. + * + */ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/gpio.h> +#include <linux/workqueue.h> +#include <linux/irq.h> +#include <linux/regmap.h> +#include <linux/err.h> +#include <linux/mfd/core.h> +#include <linux/mfd/smsc.h> +#include <linux/of_platform.h> + +struct smsc { + struct device *dev; + struct i2c_client *i2c_clients[SMSC_NUM_CLIENTS]; + struct regmap *regmap; + int clk; + /* Stored chip id */ + int id; +}; + +int smsc_read(struct device *child, unsigned int reg, + unsigned int *dest) +{ + struct smsc *smsc = dev_get_drvdata(child->parent); + + return regmap_read(smsc->regmap, reg, dest); +} +EXPORT_SYMBOL_GPL(smsc_read); + +int smsc_write(struct device *child, unsigned int reg, + unsigned int value) +{ + struct smsc *smsc = dev_get_drvdata(child->parent); + + return regmap_write(smsc->regmap, reg, value); +} +EXPORT_SYMBOL_GPL(smsc_write); + +static struct regmap_config smsc_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .cache_type = REGCACHE_COMPRESSED, +}; + +static const struct of_device_id of_smsc_match[] = { + { .compatible = "smsc,ece1099", }, + { }, +}; + +static int smsc_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct device_node *node = i2c->dev.of_node; + struct smsc *smsc; + int ret = 0; + + smsc = devm_kzalloc(&i2c->dev, sizeof(struct smsc), + GFP_KERNEL); + + smsc->regmap = devm_regmap_init_i2c(i2c, &smsc_regmap_config); + if (IS_ERR(smsc->regmap)) { + ret = PTR_ERR(smsc->regmap); + goto err; + } + + i2c_set_clientdata(i2c, smsc); + smsc->dev = &i2c->dev; + + of_property_read_u32(node, "clock", &smsc->clk); + + regmap_read(smsc->regmap, SMSC_DEV_ID, &ret); + dev_dbg(&i2c->dev, "SMSC Device ID: %d\n", ret); + + regmap_read(smsc->regmap, SMSC_DEV_REV, &ret); + dev_dbg(&i2c->dev, "SMSC Device ID: %d\n", ret); + + regmap_read(smsc->regmap, SMSC_VEN_ID_L, &ret); + dev_dbg(&i2c->dev, "SMSC Device ID: %d\n", ret); + + regmap_read(smsc->regmap, SMSC_VEN_ID_H, &ret); + dev_dbg(&i2c->dev, "SMSC Device ID: %d\n", ret); + + ret = regmap_write(smsc->regmap, SMSC_CLK_CTRL, smsc->clk); + if (ret) + goto err; + + if (node) + ret = of_platform_populate(node, NULL, NULL, &i2c->dev); + + return ret; + +err: + kfree(smsc); + return ret; +} + +static int smsc_i2c_remove(struct i2c_client *i2c) +{ + return 0; +} + +static const struct i2c_device_id smsc_i2c_id[] = { + { "smsc", 0}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, smsc_i2c_id); + +static struct i2c_driver smsc_i2c_driver = { + .driver = { + .name = "smsc", + .of_match_table = of_smsc_match, + .owner = THIS_MODULE, + }, + .probe = smsc_i2c_probe, + .remove = smsc_i2c_remove, + .id_table = smsc_i2c_id, +}; + +module_i2c_driver(smsc_i2c_driver); + +MODULE_AUTHOR("Sourav Poddar <sourav.poddar@xxxxxx>"); +MODULE_DESCRIPTION("SMSC chip multi-function driver"); +MODULE_LICENSE("GPL v2"); diff --git a/include/linux/mfd/smsc.h b/include/linux/mfd/smsc.h new file mode 100644 index 0000000..0b048c6 --- /dev/null +++ b/include/linux/mfd/smsc.h @@ -0,0 +1,89 @@ +/* + * SMSC ECE1099 + * + * Copyright 2012 Texas Instruments Inc. + * + * Author: Sourav Poddar <sourav.poddar@xxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __LINUX_MFD_SMSC_H +#define __LINUX_MFD_SMSC_H + +#include <linux/regmap.h> + +#define SMSC_ID_ECE1099 1 +#define SMSC_NUM_CLIENTS 2 + +#define SMSC_BASE_ADDR 0x38 +#define OMAP_GPIO_SMSC_IRQ 151 + +#define SMSC_MAXGPIO 32 +#define SMSC_BANK(offs) ((offs) >> 3) +#define SMSC_BIT(offs) (1u << ((offs) & 0x7)) + +struct smsc_gpio; +struct smsc_keypad; + +int smsc_read(struct device *child, unsigned int reg, + unsigned int *dest); +int smsc_write(struct device *child, unsigned int reg, + unsigned int value); + +/* Registers for SMSC */ +#define SMSC_RESET 0xF5 +#define SMSC_GRP_INT 0xF9 +#define SMSC_CLK_CTRL 0xFA +#define SMSC_WKUP_CTRL 0xFB +#define SMSC_DEV_ID 0xFC +#define SMSC_DEV_REV 0xFD +#define SMSC_VEN_ID_L 0xFE +#define SMSC_VEN_ID_H 0xFF + +/* CLK VALUE */ +#define SMSC_CLK_VALUE 0x13 + +/* Registers for function GPIO INPUT */ +#define SMSC_GPIO_DATA_IN_START 0x00 + +/* Registers for function GPIO OUPUT */ +#define SMSC_GPIO_DATA_OUT_START 0x05 + +/* Definitions for SMSC GPIO CONFIGURATION REGISTER*/ +#define SMSC_GPIO_INPUT_LOW 0x01 +#define SMSC_GPIO_INPUT_RISING 0x09 +#define SMSC_GPIO_INPUT_FALLING 0x11 +#define SMSC_GPIO_INPUT_BOTH_EDGE 0x19 +#define SMSC_GPIO_OUTPUT_PP 0x21 +#define SMSC_GPIO_OUTPUT_OP 0x31 + +#define GRP_INT_STAT 0xf9 +#define SMSC_GPI_INT 0x0f +#define SMSC_CFG_START 0x0A + +/* Registers for SMSC GPIO INTERRUPT STATUS REGISTER*/ +#define SMSC_GPIO_INT_STAT_START 0x32 + +/* Registers for SMSC GPIO INTERRUPT MASK REGISTER*/ +#define SMSC_GPIO_INT_MASK_START 0x37 + +/* Registers for SMSC function KEYPAD*/ +#define SMSC_KP_OUT 0x40 +#define SMSC_KP_IN 0x41 +#define SMSC_KP_INT_STAT 0x42 +#define SMSC_KP_INT_MASK 0x43 + +/* Definitions for keypad */ +#define SMSC_KP_KSO 0x70 +#define SMSC_KP_KSI 0x51 +#define SMSC_KSO_ALL_LOW 0x20 +#define SMSC_KP_SET_LOW_PWR 0x0B +#define SMSC_KP_SET_HIGH 0xFF +#define SMSC_KSO_EVAL 0x00 + +#endif /* __LINUX_MFD_SMSC_H */ -- 1.7.1 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
