From: Keshava Munegowda <Keshava_mgowda@xxxxxx>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@xxxxxx>
Reviewed-by: Partha Basak <parthab@xxxxxxxxxxxx>
---
drivers/mfd/omap-usb-host.c | 44 ------------------------------------------
drivers/usb/host/ehci-omap.c | 39 +++++++++++++++++++++++++++++++++++-
2 files changed, 37 insertions(+), 46 deletions(-)
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 68ac2c5..9927129 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -25,7 +25,6 @@
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/spinlock.h>
-#include <linux/gpio.h>
#include <plat/usb.h>
#include <linux/pm_runtime.h>
@@ -502,19 +501,6 @@ static void omap_usbhs_init(struct device *dev)
pm_runtime_get_sync(dev);
spin_lock_irqsave(&omap->lock, flags);
- if (pdata->ehci_data->phy_reset) {
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
- gpio_request_one(pdata->ehci_data->reset_gpio_port[0],
- GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
-
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
- gpio_request_one(pdata->ehci_data->reset_gpio_port[1],
- GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
-
- /* Hold the PHY in RESET for enough time till DIR is high */
- udelay(10);
- }
-
omap->usbhs_rev = usbhs_read(omap->uhh_base, OMAP_UHH_REVISION);
dev_dbg(dev, "OMAP UHH_REVISION 0x%x\n", omap->usbhs_rev);
@@ -593,39 +579,10 @@ static void omap_usbhs_init(struct device *dev)
usbhs_omap_tll_init(dev, OMAP_TLL_CHANNEL_COUNT);
}
- if (pdata->ehci_data->phy_reset) {
- /* Hold the PHY in RESET for enough time till
- * PHY is settled and ready
- */
- udelay(10);
-
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
- gpio_set_value
- (pdata->ehci_data->reset_gpio_port[0], 1);
-
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
- gpio_set_value
- (pdata->ehci_data->reset_gpio_port[1], 1);
- }
-
spin_unlock_irqrestore(&omap->lock, flags);
pm_runtime_put_sync(dev);
}
-static void omap_usbhs_deinit(struct device *dev)
-{
- struct usbhs_hcd_omap *omap = dev_get_drvdata(dev);
- struct usbhs_omap_platform_data *pdata = &omap->platdata;
-
- if (pdata->ehci_data->phy_reset) {
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
- gpio_free(pdata->ehci_data->reset_gpio_port[0]);
-
- if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
- gpio_free(pdata->ehci_data->reset_gpio_port[1]);
- }
-}
-
/**
* usbhs_omap_probe - initialize TI-based HCDs
@@ -861,7 +818,6 @@ static int __devexit usbhs_omap_remove(struct platform_device *pdev)
{
struct usbhs_hcd_omap *omap = platform_get_drvdata(pdev);
- omap_usbhs_deinit(&pdev->dev);
iounmap(omap->tll_base);
iounmap(omap->uhh_base);
clk_put(omap->init_60m_fclk);
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index bba9850..5c78f9e 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -42,6 +42,7 @@
#include <plat/usb.h>
#include <linux/regulator/consumer.h>
#include <linux/pm_runtime.h>
+#include <linux/gpio.h>
/* EHCI Register Set */
#define EHCI_INSNREG04 (0xA0)
@@ -191,6 +192,19 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
}
}
+ if (pdata->phy_reset) {
+ if (gpio_is_valid(pdata->reset_gpio_port[0]))
+ gpio_request_one(pdata->reset_gpio_port[0],
+ GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
+
+ if (gpio_is_valid(pdata->reset_gpio_port[1]))
+ gpio_request_one(pdata->reset_gpio_port[1],
+ GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
+
+ /* Hold the PHY in RESET for enough time till DIR is high */
+ udelay(10);
+ }
+
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
@@ -237,6 +251,19 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
/* root ports should always stay powered */
ehci_port_power(omap_ehci, 1);
+ if (pdata->phy_reset) {
+ /* Hold the PHY in RESET for enough time till
+ * PHY is settled and ready
+ */
+ udelay(10);
+
+ if (gpio_is_valid(pdata->reset_gpio_port[0]))
+ gpio_set_value(pdata->reset_gpio_port[0], 1);
+
+ if (gpio_is_valid(pdata->reset_gpio_port[1]))
+ gpio_set_value(pdata->reset_gpio_port[1], 1);
+ }
+
return 0;
err_add_hcd:
@@ -259,8 +286,9 @@ err_io:
*/
static int ehci_hcd_omap_remove(struct platform_device *pdev)
{
- struct device *dev = &pdev->dev;
- struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct device *dev = &pdev->dev;
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
+ struct ehci_hcd_omap_platform_data *pdata = dev->platform_data;
usb_remove_hcd(hcd);
disable_put_regulator(dev->platform_data);
@@ -269,6 +297,13 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev)
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
+ if (pdata->phy_reset) {
+ if (gpio_is_valid(pdata->reset_gpio_port[0]))
+ gpio_free(pdata->reset_gpio_port[0]);
+
+ if (gpio_is_valid(pdata->reset_gpio_port[1]))
+ gpio_free(pdata->reset_gpio_port[1]);
+ }
return 0;
}
--
1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
