Re: Booting hangs with updated linux-omap kernel on OMAP3EVM

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Aug 29, 2011 at 4:18 PM, Ravi, Deepthy <deepthy.ravi@xxxxxx> wrote:
> Hi,
> I tried booting OMAP3EVM with the updated linux-omap kernel .
> The last commit details on the kernel are :
> Author: Tony Lindgren <tony@xxxxxxxxxxx>
> commit b148d763841161894ed6629794064065a834aa2b
> Linux-omap rebuilt: Updated to use omap_sdrc_init
>
> It hangs at one point.
>
> Following is the boot log,
>
> Texas Instruments X-Loader 1.51 (May  3 2011 - 19:22:23)
> Starting X-loader on MMC
> Reading boot sector
>
> 220008 Bytes Read from MMC
> Starting OS Bootloader from MMC...
> Starting OS Bootloader...
>
>
> U-Boot 2010.06 (May 03 2011 - 19:23:34)
>
> OMAP3430/3530-GP ES3.1, CPU-OPP2 L3-165MHz
> OMAP3 EVM board + LPDDR/NAND
> I2C:   ready
> DRAM:  128 MiB
> NAND:  HW ECC [Kernel/FS layout] selected
> 256 MiB
> In:    serial
> Out:   serial
> Err:   serial
> Read back SMSC id 0x92200000
> Die ID #46a400040000000004032d460d01d014
> Net:   smc911x-0
> Hit any key to stop autoboot:  0
> OMAP3_EVM #
> OMAP3_EVM #
> OMAP3_EVM # run myboot
> smc911x: detected LAN9220 controller
> smc911x: phy initialized
> smc911x: MAC 00:50:c2:7e:93:73
> Using smc911x-0 device
> TFTP from server 192.168.1.79; our IP address is 192.168.1.123
> Filename 'uImage'.
> Load address: 0x80000000
> Loading: #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         #################################################################
>         ##########################################################
> done
> Bytes transferred = 3287400 (322968 hex)
> mmc1 is available
> reading ramdisk.gz
>
> 2013059 bytes read
> ## Booting kernel from Legacy Image at 80000000 ...
>   Image Name:   Linux-3.1.0-rc3-11176-g2e5a5f9-d
>   Image Type:   ARM Linux Kernel Image (uncompressed)
>   Data Size:    3287336 Bytes = 3.1 MiB
>   Load Address: 80008000
>   Entry Point:  80008000
>   Verifying Checksum ... OK
>   Loading Kernel Image ... OK
> OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
> [    0.000000] Linux version 3.1.0-rc3-11176-g2e5a5f9-dirty (x0157478@psplinux060) (gcc version 4.3.3 (GCC) ) #4 SMP Mon Aug 29 15:37:16 IST 2011
> [    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
> [    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
> [    0.000000] Machine: OMAP3 EVM
> [    0.000000] Memory policy: ECC disabled, Data cache writeback
> [    0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
> [    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
> [    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
> [    0.000000] PERCPU: Embedded 8 pages/cpu @c0cef000 s10112 r8192 d14464 u32768
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
> [    0.000000] Kernel command line: mem=128M console=ttyO0,115200n8 root=/dev/ram0 initrd=0x82000000,40M ramdisk_size=32768 ip=dhcp
> [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
> [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> [    0.000000] Memory: 128MB = 128MB total
> [    0.000000] Memory: 76736k/76736k available, 54336k reserved, 0K highmem
> [    0.000000] Virtual kernel memory layout:
> [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
> [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
> [    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
> [    0.000000]     vmalloc : 0xc8800000 - 0xf8000000   ( 760 MB)
> [    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
> [    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
> [    0.000000]       .text : 0xc0008000 - 0xc05c0d30   (5860 kB)
> [    0.000000]       .init : 0xc05c1000 - 0xc060e780   ( 310 kB)
> [    0.000000]       .data : 0xc0610000 - 0xc0695490   ( 534 kB)
> [    0.000000]        .bss : 0xc06954b4 - 0xc0bea4f4   (5461 kB)
> [    0.000000] Hierarchical RCU implementation.
> [    0.000000] NR_IRQS:410
> [    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
> [    0.000000] Total of 96 interrupts on 1 active controller
> [    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
> [    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
> [    0.000000] Console: colour dummy device 80x30
> [    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> [    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
> [    0.000000] ... MAX_LOCK_DEPTH:          48
> [    0.000000] ... MAX_LOCKDEP_KEYS:        8191
> [    0.000000] ... CLASSHASH_SIZE:          4096
> [    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
> [    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
> [    0.000000] ... CHAINHASH_SIZE:          16384
> [    0.000000]  memory used by lock dependency info: 3695 kB
> [    0.000000]  per task-struct memory footprint: 1152 bytes
> [    0.001159] Calibrating delay loop... 497.82 BogoMIPS (lpj=1941504)
> [    0.093749] pid_max: default: 32768 minimum: 301
> [    0.094696] Security Framework initialized
> [    0.095092] Mount-cache hash table entries: 512
> [    0.100982] CPU: Testing write buffer coherency: ok
> [    0.104583] Brought up 1 CPUs
> [    0.104583] SMP: Total of 1 processors activated (497.82 BogoMIPS).
> [    0.119812] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
> [    0.122406] omap_hwmod: am35x_otg_hs: cannot be enabled (3)
> [    0.126739] print_constraints: dummy:
> [    0.128570] NET: Registered protocol family 16
> [    0.129302] GPMC revision 5.0
> [    0.133789] omap_device: omap_gpio.0: new worst case activate latency 0: 61035
> [    0.135772] OMAP GPIO hardware version 2.5
> [    0.144104] omap_mux_init: Add partition: #1: core, flags: 0
> [    0.151336] omap_device: omap_uart.0: new worst case activate latency 0: 30517
> [    0.151824] omap_device: omap_uart.0: new worst case deactivate latency 0: 30517
> [    0.154479] Reprogramming SDRC clock to 332000000 Hz
> [    0.261108] hw-breakpoint: debug architecture 0x4 unsupported.
> [    0.275268] omap_device: omap-mcbsp.2: alias fck already exists
> [    0.276336] omap_device: omap-mcbsp.3: alias fck already exists
> [    0.283660] OMAP DMA hardware revision 4.0
> [    0.369995] bio: create slab <bio-0> at 0
> [    0.381835] SCSI subsystem initialized
> [    0.382568] omap_device: omap2_mcspi.1: new worst case activate latency 0: 30517
> [    0.386871] omap_device: omap2_mcspi.1: new worst case deactivate latency 0: 30517
> [    0.395294] usbcore: registered new interface driver usbfs
> [    0.396789] usbcore: registered new interface driver hub
> [    0.397979] usbcore: registered new device driver usb
> [    0.401397] omap_device: omap_i2c.1: new worst case activate latency 0: 61035
> [    0.414520] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
> [    0.427642] twl4030: PIH (irq 7) chaining IRQs 368..375
> [    0.427917] twl4030: power (irq 373) chaining IRQs 376..383
> [    0.430664] twl4030: gpio (irq 368) chaining IRQs 384..401
> [    0.432861] _omap_mux_init_gpio: Could not set gpio192
> [    0.447387] print_constraints: VIO: 1800 mV normal standby
> [    0.450561] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
> [    0.453948] print_constraints: VDAC: 1800 mV normal standby
> [    0.456970] print_constraints: VPLL2: 1800 mV normal standby
> [    0.459869] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
> [    0.460601] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517
> [    0.469146] omap_i2c omap_i2c.2: bus 2 rev3.12 at 400 kHz
> [    0.484619] omap_i2c omap_i2c.3: bus 3 rev3.12 at 400 kHz
> [    0.496002] Switching to clocksource 32k_counter
> [    0.500366] Switched to NOHz mode on CPU #0
> [    0.648468] NET: Registered protocol family 2
> [    0.649505] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.651916] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> [    0.652313] TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
> [    0.655578] TCP: Hash tables configured (established 4096 bind 4096)
> [    0.655731] TCP reno registered
> [    0.655792] UDP hash table entries: 64 (order: 0, 5120 bytes)
> [    0.656188] UDP-Lite hash table entries: 64 (order: 0, 5120 bytes)
> [    0.657409] NET: Registered protocol family 1
> [    0.659240] RPC: Registered named UNIX socket transport module.
> [    0.659271] RPC: Registered udp transport module.
> [    0.659301] RPC: Registered tcp transport module.
> [    0.659301] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [    0.660522] Trying to unpack rootfs image as initramfs...
> [    0.663604] rootfs image is not initramfs (no cpio magic); looks like an initrd
> [    1.100158] Freeing initrd memory: 40960K
> [    1.100189] NetWinder Floating Point Emulator V0.97 (double precision)
> [    1.293945] VFS: Disk quotas dquot_6.5.2
> [    1.294403] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [    1.298278] JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
> [    1.299865] msgmni has been set to 229
> [    1.305603] io scheduler noop registered
> [    1.305633] io scheduler deadline registered
> [    1.305938] io scheduler cfq registered (default)
> [    1.311401] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> [    1.321380] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
> [    2.004119] console [ttyO0] enabled
> [    2.009979] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
> [    2.019348] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
> [    2.073333] brd: module loaded
> [    2.104248] loop: module loaded
> [    2.117248] mtdoops: mtd device (mtddev=name/number) must be supplied
> [    2.124542] omap2-nand driver initializing
> [    2.130157] OneNAND driver initializing
> [    2.143341] smsc911x: Driver version 2008-10-21
> [    2.157897] smsc911x-mdio: probed
> [    2.162200] smsc911x smsc911x.0: eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:01, irq=-1)
> [    2.172760] smsc911x smsc911x.0: eth0: MAC Address: 00:50:c2:7e:93:73
> [    2.181335] usbcore: registered new interface driver asix
> [    2.188140] usbcore: registered new interface driver cdc_ether
> [    2.195220] usbcore: registered new interface driver net1080
> [    2.202087] usbcore: registered new interface driver cdc_subset
> [    2.209228] usbcore: registered new interface driver zaurus
> [    2.215179] cdc_ncm: 04-Aug-2011
> [    2.219482] usbcore: registered new interface driver cdc_ncm
> [    2.228881] usbcore: registered new interface driver cdc_wdm
> [    2.235046] Initializing USB Mass Storage driver...
> [    2.241119] usbcore: registered new interface driver usb-storage
> [    2.247680] USB Mass Storage support registered.
> [    2.254272] usbcore: registered new interface driver libusual
> [    2.261352] usbcore: registered new interface driver usbtest
> [    2.269836] mousedev: PS/2 mouse device common for all mice
> [    2.279449] input: TWL4030 Keypad as /devices/platform/omap/omap_i2c.1/i2c-1/1-004a/twl4030_keypad/input/input0
> [    2.292724] omap_device: omap_i2c.1: new worst case activate latency 0: 122070
> [    2.309844] ads7846 spi1.0: touchscreen, irq 335
> [    2.316070] omap_device: omap2_mcspi.1: new worst case activate latency 0: 61035
> [    2.326538] input: ADS7846 Touchscreen as /devices/platform/omap/omap2_mcspi.1/spi1.0/input/input1
> [    2.344512] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input2
> [    2.362396] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
> [    2.369415] twl_rtc twl_rtc: Power up reset detected.
> [    2.375915] twl_rtc twl_rtc: Enabling TWL-RTC.
> [    2.382354] i2c /dev entries driver
> [    2.392242] Driver for 1-wire Dallas network protocol.
> [    2.400451] omap_device: omap_wdt.-1: new worst case activate latency 0: 30517
> [    2.410400] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> [    2.417083] omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30517
> [    2.426544] twl4030_wdt twl4030_wdt: Failed to register misc device
> [    2.433471] twl4030_wdt: probe of twl4030_wdt failed with error -16
> [    2.446990] omap_device: omap_hsmmc.0: new worst case activate latency 0: 213623
> [    2.460815] omap_device: omap_hsmmc.0: new worst case deactivate latency 0: 30517
> [    2.474273] omap_device: omap_hsmmc.0: new worst case activate latency 0: 274658
> [    2.483215] usbcore: registered new interface driver usbhid
> [    2.489227] usbhid: USB HID core driver
> [    2.493286] oprofile: hardware counters not available
> [    2.498687] oprofile: using timer interrupt.
> [    2.503967] TCP cubic registered
> [    2.507507] Initializing XFRM netlink socket
> [    2.512207] NET: Registered protocol family 17
> [    2.517120] NET: Registered protocol family 15
> [    2.522277] Registering the dns_resolver key type
> [    2.528106] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
> [    2.536346] ThumbEE CPU extension supported.
> [    2.602478] clock: disabling unused clocks to save power
> [    2.617614] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
> [    2.629364] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xc8878000, IRQ: 336
> [    2.660919] Sending DHCP requests .
> [    3.008392] mmc0: new high speed SD card at address b368
> [    3.018829] mmcblk0: mmc0:b368 SDC   958 MiB
> [    3.034332]  mmcblk0: p1 p2
> [    3.138000] omap_device: omap_hsmmc.0: new worst case deactivate latency 0: 91552
> [    5.645111] ., OK
> [    6.387817] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.1.57
> [    6.396301] IP-Config: Complete:
> [    6.399719]      device=eth0, addr=192.168.1.57, mask=255.255.255.0, gw=192.168.1.1,
> [    6.407775]      host=192.168.1.57, domain=pathpartner.com, nis-domain=(none),
> [    6.415496]      bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
> [    6.426513] RAMDISK: gzip image found at block 0
> [    7.078247] VFS: Mounted root (ext2 filesystem) on device 1:0.
> [    7.085693] Freeing init memory: 308K
>
> It hangs after this. Did anyone face this issue?

Can you check the serial port parameter in inittab of your filesystem.

Regards,
Kishore
>
>
> Thanks,
> Deepthy Ravi.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux